OpenEye OE2-E120 Quick Start
SET UP CONTINUOUS RECORDING
BACK UP RECORDED VIDEO
LOGGING IN FOR THE FIRST TIME
SEARCH RECORDED VIDEO WITH QUICK SEARCH
SCREEN ICONS
Recording
Continuous
V
F
P
1:
C1:
Video Loss
Channel Name
Motion
Sensor
Freeze
PTZ
Channel
This icon always appears in conjunction with the Motion or
Continuous Recording icon.
Motion Recording
Sensor (Alarm) Recording
Continuous Recording
Video Loss Detected
Pause Live View
PTZ Camera Channel
Channel Number
User Defined Channel Name
QUICK BACKUP
PLAY BACKUP FILE ON A PC
DVR User ID:
Password:
admin
<none>
After logging in for the first time, change the admin password for the DVR and
Note
remote software to establish user level security. See the Manual for instructions.
LED STATUS INDICATOR
Power
Record
Network
Illuminates when power is supplied to the DVR.
HDD
Flashes when the hard drive is being accessed.
Flashes when live video is recording.
Illuminates when the DVR is connected to a network.
Fan
Illuminates when the fan is working. Flashes when the fan is working
improperly. Unlit when the fan is not working.
ENTER / EXIT BUTTONS
Enter
Input data, make selections, and open pop-up menus.
Exit
Return to the previous mode or menu, without saving.
NUMERIC BUTTONS AND REC
Remote Software User ID:
Password:
admin1
<none>
S
P
Smart
Panorama
Pause
Smart Search Mode
Panorama Search Mode
Play
Playback Mode
Pause Search Video
23221 E Knox Ave
Liberty Lake, WA 99019
1.888.542.1103
A12931
28971AB
Copyright ©2009 OpenEye. All Rights Reserved. Information contained in this
document is subject to change without prior notice. OpenEye does its best to provide
accurate information but cannot be held responsible for typos or mistakes.
Numeric
Record
In live and search modes, press to watch that channel full screen.
In live mode, press to start instant recording of all channels.
DIRECTIONAL AND PLAYBACK CONTROL BUTTONS
Operation Modes: Live Mode, Live Freeze Mode, Search Mode, Search-Pause Mode,
Navigation Mode, and PTZ Mode.
Live
Go to PTZ mode.
PTZ
Adjust zoom, focus, and iris on a PTZ channel.
Search
Search-Pause
Start reverse playback of recordings. When pressed successively, the
search jumps back in time by 30 minute increments.
When pressed successively, the reverse playback rate
decreases from 1/2X speed to 1/8X.
Live
Freeze live channels.
Live Freeze
Search
Search Pause
Resume live view.
Pause playback channels.
Resume playback.
FUNCTION BUTTONS
Search
Open the search menu.
Live
PTZ
Search
Search-Pause
Navigation
PTZ
Search
Navigation
PTZ
Search
Search-Pause
Navigation
PTZ
Search
Navigation
PTZ
Search
Search-Pause
Start playback of the latest recordings.
(By default, the system searches recordings in the past 30 secs. If no
recording is archived, the system will play back the latest one.)
Adjust zoom, focus, and iris on a PTZ channel.
Start playback of recordings. When pressed successively, the search
jumps forward in time by 30 minute increments.
When pressed successively, the playback rate increases from 1/2X
speed to 1/8X.
Move up.
Move the camera view point up.
Start Panorama Search.
Move to the right.
Move the camera view point to the right.
Play recorded videos.
Step forward one frame.
Move down.
Move the camera view point down.
Start Smart Search.
Move to the left.
Move camera’s view point to the left.
Play recorded videos in reverse.
Step back one frame.
Focus
Backup
Zoom
Rotate
Preset
Key
Iris
Live
Setup
In PTZ mode, press to use the Focus function.
Use the buttons to adjust.
In live mode, press to open the backup menu.
In the search mode,
Press once, to set the start time for Backup.
•
Press twice, to set the end time for Backup.
•
Press three times, to complete Backup.
•
In PTZ mode, press to use PTZ Zoom function.
Use the buttons to adjust.
Rotate through to the remaining channels in the current display mode or
rotate the display configuration.
In PTZ mode, press to use the Preset function.
Log out the current user. Use to prevent accidental or unauthorized system-wide changes.
In PTZ mode, press to use the IRIS function.
Use the buttons to adjust.
Change the display mode. Display switches in the following order when
the LIVE key is pressed successively: (Single > 4 > 7 > 9 > 10 > 13 > 16
> Single > 4 > 7 > 9 ...split screen mode)
Open the setup menu.
HOW TO USE IR REMOTE CONTROLLER
When more than one E-Series DVR is installed in the same location, use one remote controller
to control multiple DVRs. To control multiple DVRs, you must change the remote controller ID to
match the SYSTEM ID of the DVR.
Follow the instructions below to change the remote controller ID.
On the DVR
Press SETUP on the front of the DVR or the Remote Controller.
1.
Go to SYSTEM > SYSTEM SETUP.
2.
Enter the desired SYSTEM ID number.
3.
On the Remote Controller
Press and hold the ID button on the remote controller and enter the desired SYSTEM ID
4.
number to operate the corresponding DVR.
Note The SYSTEM ID must be input as two numbers on the remote controller. Therefore you
should input 00 for the DVR ID 0 and input 01 for 1.
QUICK INSTALLATION
Connect cameras to video inputs, and if using, connect PTZ camera control lines to RS485
1.
connector.
Connect the main monitor to the VGA monitor output or main video output - BNC.
2.
Connect analog monitors to looping video outputs. (optional)
3.
Connect the monitor to SPOT video outputs (up to 3 on 16CH only). (optional)
4.
Connect sensors to alarm signal inputs. (optional)
5.
Connect alarm devices such as buzzers to alarm signal outputs. (optional)
6.
Connect external controllers to RS232 connector. (optional)
7.
Connect a speaker and microphone to the audio inputs and output. (optional)
8.
Connect a network cable to the network port.
9.
Power on all the connected equipment.
10.
Connect the power cord to the DVR.
11.
Turn the power switch on.
12.
Loading...