OpenEye D4000 Quick Start
CA-D4000 | Camera Tester
Quick Guide
This quick operation guide is a quick reference for users to install and operate the D4000 camera tester and only provides basic information on the settings and operation. Before attempting
to connect, congure and operate the tester, please read the user manual thoroughly.
Box Contents
D4000 Tester BNC Cable Network Cable
Li-ion Battery Soft Carrying Case DC 12V Adapter
UTP Terminal Block CD Quick Start Sheet
Connections
LAN / PoE out
LAN / PSE in
Micro SD slot
USB
Main power switch
Video in Video out
Power indicator Data TX/RX indicator
Stylus storage slot
Light sensor
LCD screen
Shift/PTZ control keys
Dimensions
99.3 mm
38 mm
170 mm
Powering On / Off
To power on the IP Camera Tester:
1. Set the Main Power Slide Switch on the side to “ON” position.
2. Press the Start Key and hold for 3 seconds. The Power Indicator LED (above the
screen) will light.
3. When the Tester powers on, a loading bar will display on the screen for 10 seconds and
the Data TX/RX Indicator LED will blink.
4. The Home Screen will display within 50 seconds.
Charging the Battery
The IP Camera Tester uses a rechargeable Li-ion battery pack that takes approximately four
hours to charge, and provides the Tester with up to three hours of operating life.
To charge the battery:
1. Plug the included DC 12V adapter in the side of the Tester.
2. While the battery is charging, the charging indicator light (above the power cable) will
illuminate. When the battery is completly charged, the light will turn off.
Audio out
Audio in
Item Description
LAN / PoE out
LAN / PSE in N/A
Micro SD slot Data storage up to 4GB.
USB Use for rmware upgrades or external storage.
Video in Connect to camera with BNC cable.
Video out Connect to monitor with BNC cable.
Stylus storage slot Use the included stylus for touch screen operation.
Power indicator The LED is lit when the power is on.
Data TX/RX Indicator The LED ashes when the Tester is under operation.
Light sensor
LCD screen 3.5” screen displays video and camera setup menus.
Shift/PTZ control keys
ESC
Start/Enter/Snapshot
Main power switch Switch to on before pressing the Start key.
Audio out Connect to a headset.
Audio in Connect to a microphone.
Charging indicator The light will stay lit while the battery is charging.
UTP cable tester
DC 12V power adapter Connect the supplied DC adapter.
RS-485 Terminal Block
Speaker For audio output.
Charging indicator
UTP cable tester
DC 12V power adapter
RS-485 terminal block
Connect the LAN cable from the PoE-enabled IP
camera.
The light sensor detects environmental brightness to
automatically adjust the LCD screen brightness.
Press the arrow keys to navigate the setup icons,
items in a menu, or use the keys to control a connected PTZ camera.
Press to exit a menu without saving or return to the
previous page.
Start: Turn on the Main Power Switch, then press
this key for 3 seconds to start the tester.
Enter: Press this key to enter a sub-menu or save
setup.
Snapshot: When viewing IP camera video, press this
key for an image snapshot. Press the key and the
snapshot menu will open within 5 seconds. Tap Enter
to save the settings of the image.
Use a network cable to connect the tester to the
CAT5 UTP terminator for detecting wiring types
(straight/corss) or errors (open, short, miswired) using the wire map displayed on the screen.
Connect the RS-485 lines to the terminal block correctly for the dome camera’s PTZ control.
ESC Start/Enter/Snapshot
Speaker
23221 E Knox Ave
Liberty Lake, WA 99019
1.888.542.1103
A12931
Copyright ©2011 OpenEye. All Rights Reserved. Information contained in this document
is subject to change without prior notice. OpenEye does its best to provide accurate
information but cannot be held responsible for typos or mistakes.
30640AA
Loading...