OpenEye CM-P307 User Manual

High Resolution Outdoor

Dome Camera

Camera Installation & Conguration

Model no: CM-P307

CM-P307R

Please carefully read these instructions before using this product.

Save this document for future use.

31361AA

Regulatory Compliance

Emissions FCC part 15, subpart B, Class A
CE: EN61000-6-4:2007

Immunity CE: EN60130-4:1995 + A1:1998 + A2:2003

FCC COMPLIANCE

This product has been tested and found to comply with the limits for a Class A
digital device pursuant to Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. The product generates, uses, and can
radiate radio frequency energy, and, if not installed and used in accordance with
the manufacturer’s instruction manual, may cause harmful interference with radio
communications. Operation of this product in a residential area is likely to cause
harmful interference, in which case you will be required to correct the interference
at your own expense.

This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference
that may cause undesired operation.

These limits are designed to provide reasonable protection against harmful
interference in a non-residential installation. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference with the radio or television reception, which can be deter­mined by turning the equipment off and on, you are encouraged to try to correct
the interference by one or more of the following measures:

1. Reorient or relocate the antenna of the radio/television receiver.

2. Increase the separation between this equipment and the radio/television
receiver.

3. Plug the equipment into a different outlet so that the equipment and the
radio/television receiver are on different power mains branch circuits.

4. Consult the dealer or an experienced radio/television technician for
additional suggestions.

General Specications

Model No. CM-P307 CM-P307R

Image Sensor 1/3” Sony CCD

IP Rating IP67

Type / Format NTSC

Wide Dynamic Range Yes, Digital WDR

Minimum Illumination 0.05 Lux @ 50 IRE;

Day / Night True Day/Night

Resolution 650 TVL

Service Monitor Jack Yes

S/N Ratio >50dB

Focal Length 2.8 ~ 12 mm

Iris Control Auto-iris

Synchronization Internal

Video Output 1.0Vpp 75Ω BNC Unbalanced

White Balance ATW, Manual

Auto White Balance Range 2500K ~ 9500K

Backlight Compensation BLC, HLC, Off

Auto Gain Control Low, Mid, High, Off

Operating Temperature -49˚ ~ 122˚ F (-45˚ ~ 50˚C)

Heater Yes

Power Consumption 4.32W (24vAC)

Rated Amperage 0.24A 0.45A

Input Voltage 12vDC / 24vAC

Weight 1.8 lbs (0.82 kg)

Dimensions Dome : ø5.925” (150.5 mm) x H: 5.3” (130.5 mm)

Housing / Dome Cover White / Clear

0.01 Lux @ 30 IRE

2.16W (12vDC)

0.05 Lux @ 50 IRE;

0.01 Lux @ 30 IRE;

0.00 Lux (IR LEDs on)

10.8W (24vAC)

5.4W (12vDC)

Box Contents

• Screws (x3)

• Washers (x3)

• Torx security tool

• Service monitor cable

Dimensions

23221 E Knox Ave
Liberty Lake, WA 99019

1.888.542.1103
www.openeye.net

Precaution

• Do not attempt to dismantle the camera module mounted

within the dome. There are no user serviceable parts in
the camera module. Refer servicing to a qualied profes­sional.

• Handle the camera with care. Do not abuse the camera.

Avoid striking or shaking it. Improper handling and stor­age could damage the camera.

• Do not operate the camera beyond its temperature or

power source rating. Refer to the environmental informa­tion provided in this document.

Features

• 650 TV-Line Resolution

• Digital Noise Reduction

• 3-axis camera

• IP67-rated

• Digital Wide Dynamic Range

• True Day/Night

Installation

Using a Pole Mount

1. Remove the screw on the bottom of the camera hous­ing.

2. Open the dome cover.

3. Remove the tap cover and insert cables.

4. Apply teon tape to the threaded portion of the pole
mount. (Use of teon tape is necessary for water resis­tence in outdoor applications).

5. Screw the pole mount into the base of the camera.

Camera Installation

1. Use the supplied screws to mount the camera on a wall
or ceiling.

2. If your camera uses a varifo­cal lense, adjust the lens
by opening the LED cover.
Turn the Tele-Wide knob to

adjust the eld of view. Turn

the Near-Far knob to set the
focus.

3. Once the camera is mounted
to the desired surface and is
focused correctly, re-assemble
the camera housing.

Adjusting the Camera Angle

1. To adjust the pan, the camera xture left or right within a
range of -160º ~ 190º.

2. To adjust the tilt, grasp the LED cover and adjust the
direction up or down within a range of 6º ~ 90º.

3. To adjust the vertical orientation, rotate the camera
holder within a range of -178º ~ 178º.

Camera OSD Menu

EXPOSURE

LENS
SELECT

AGC OFF, LOW, MIDDLE, HIGH Auto Day/Night is

SENSE-UPAUTO, OFF, X2, X4, X8, X16,

BACK­LIGHT

3D-DNR OFF, LOW, MID, HIGH, AUTO Reduce noise in low

WHITE BALANCE

AWB
MODE

R-Y GAIN 0 ~ 255 Adjust red tone of image

B-Y GAIN 0 ~ 255 Adjust blue tone of image

MANUAL BRIGHTNESS 0 ~ 99

E. SHUTTER AUTO, 1/60 ~

DC BRIGHTNESS 0 ~ 99

E. SHUTTER AUTO, 1/60 ~

X32, X64, X128, X256, X512,
X1024

BLC BLC LEVEL OFF, LOW, MID,

TOP 0 ~ 15:

BOTTOM 0 ~ 16

LEFT 0 ~ 15

RIGHT 0 ~ 16

HLC HBLC OFF

MODE ALL DAY, NIGHT

HLC LEVEL 1 ~ 100

MASK 1-4 ON

D-WDR SET LEVEL 0 ~ 20

ATW Color temp. 2500 ~ 9500 K

MANUAL M-WR 0 ~ 128: Adjust the

M-WB 0 ~ 128: Adjust the

PUSH Optimize white balance for current condi-

tions

1/100000

1/100000

disabled if AGC is
OFF

Use sense-up in low

light environments

HIGH

MANUAL HBLC LEVEL:

OFF,LOW, MID, HIGH
TOP, BOTTOM, LEFT, RIGHT
same as BLC

TOP: 0 ~ 33
BOTTOM: 1 ~ 34
LEFT: 0 ~ 44
RIGHT 1 ~ 45

OFF: HLC MASK
OFF

light environments

red value

blue value

DAY & NIGHT

D&N
MODE

BURST ON, OFF Enable/disable burst

C-SUP 0 ~ 100 Color suppress

A-SUP 0 ~ 100 Iris suppress control

SMART IRON, OFF Decreases screen

MIRROR MIRROR, OFF Vertical image

SHARP­NESS

GAMMA 0.45, 0.55, 0.65

PRIVACY

MASK
1 ~ 8

AUTO DAY-NIGHT 7 ~ 30

NIGHT-DAY 6 ~ 29

DELAY TIME 0 ~ 15: Set the

AUTO-

CDS

COLOR Fixed at Color

B&W Fixed at B&W

EXT DELAY TIME 0 ~ 15

0 ~ 30

USER GAMMA .20 ~ 1.00 by incre-

OFF

ON DOT SEL L_TOP, L_BOT,

A. DAY-NIGHT 6 ~ 36

A. NIGHT-DAY 6 ~ 36

C. DAY-NIGHT 0 ~ 255

C. NIGHT-DAY 0 ~ 255

DOT XY ENTER SETTING:

MOVE XY ENTER SETTING:

COLOR Select mask color

duration

signal in BW mode

control

saturation of objects
within a short range

inversion

ments of .05

R_BOT, R_TOP:
Determines location
for Motion Detection

Determines coor­dinates

Determines coor­dinates

SPECIAL

LANGUAGE Select language (9

TITLE OFF-ON EDIT Display the camera

RESET Camera name reset

POSITION Camera name

DPC OFF Deactivates Detect

AUTO WHITE THR 0 ~ 255: Set the

LUMA THR 0 ~ 255: Set the

RETURN Move back to previ-

FACTORY SET YES, NO Reset your camera

EXIT

SAVE AND EXIT Save the value and

EXIT Escape the menu

available)

name on screen

position

Pixel Correction in
low illumination

limited value of white
pixel correction

limited value of white
pixel correction

ous menu.

to factory default
conditon

exit the menu

without saving

Function Setting

1. Push the lever to access the menu and conrm selec-

tion. Push the lever for one second to open or close the

menu. Use the lever to return to the previous menu from

motion detection or privacy mask setting sections.

2. Push the lever up to move the cursor up.

3. Push the lever down to move the cursor down.

4. Push the lever left to move the cursor left.

5. Push the lever right to move the cursor right.

6. Plug a test monitor into the optional EXT-VIDEO termi­nal to view menu screens during installation.

7. Adjust the LED light level with the screw.