OpenEye CM-611 Quick Start
CM-611/711 | Indoor/Outdoor IP Dome Camera
Quick Guide
This quick operation guide is a quick reference for users to install and operate the dome
camera and only provides basic information on the camera’s settings and operation. Before
attempting to connect, congure and operate the dome camera, please read the user manual
thoroughly.
Box Contents
CM-611/711 Camera Self-Tapping Screws Plastic Anchors
Rubber Washers
(CM-711 only) Security Torx Tool Quick Start Guide
CD
Connecting to the IP Camera
To access the camera setup menu, you need to install the viewer software on your PC or re-
corder. The viewer software will install automatically the rst time you connect to the camera. If
your internet browser doesn’t install the viewer software, check the security settings or ActiveX
controls and plug-in settings. If your internet browser asks for permission to install the ActiveX
control, you must allow the ActiveX control to continue the installation.
To enable installation of ActiveX controls on Internet Explorer:
1. From the Tools menu, click Internet Options.
2. Click the Security tab and then click the Internet icon.
3. Click Custom Level and ensure that all ActiveX controls and plug-ins are set to En-
able or Prompt.
To add the camera to your trusted sites:
1. From the Tools menu, click Internet Options.
2. Click the Security tab and then click the Trusted Sites icon.
3. Click Sites.
4. Type the IP Address of the camera. Ensure that the Require server verication check
box is cleared.
Connections
The CM-611 and CM-711 cameras use Power over Ethernet (PoE) to power the camera.
Make sure the power sourcing equipment (PSE) is in use in the network.
Connect one end of the PoE cable to the Ethernet port (RJ45) on the camera and the other
end to the PSE hub or router.
Check the status of the network connection by looking at the link indicator and
activity indicator LEDs. If the LEDs are not lit check your network connection.
The green link LED indicates a network connection and the orange activity LED
ashes to indicate network activity.
Connecting to the IP Camera
To access your CM-611 or CM-711 setup menu, you need to install the OpenEye Network
Camera Manager on your PC or recorder. To install the OpenEye Network Camera Manager
application on your PC, insert the included software CD, or download the program from openeye.net, and follow the prompts.
1. Open Network Camera Manager, and click Find Devices.
2. Locate your camera on the Network Camera Manager list.
3. To open the viewer software in your web browser, double-click the camera, and then click
Browse.
The rst time you connect to the camera you will automatically prompted to install the ActiveX
controller. If your internet browser doesn’t install the viewer software, check the security settings or ActiveX controls and plug-in settings. If your internet browser asks for permission to
install the ActiveX control, you must allow the ActiveX control to continue the installation.
To enable installation of ActiveX controls on Internet Explorer:
1. From the Tools menu, click Internet Options.
2. Click the Security tab and then click the Internet icon.
3. Click Custom Level and ensure that all ActiveX controls and plug-ins are set to En-
able or Prompt.
To add the camera to your trusted sites:
1. From the Tools menu, click Internet Options.
2. Click the Security tab and then click the Trusted Sites icon.
3. Click Sites.
4. Type the IP Address of the camera. Ensure that the Require server verication check
box is cleared.
For additional information on adjusting the settings of your internet browser contact your system administrator or refer to the FAQs at openeye.net.
Default Username and Password
The username and password are case sensitive. It is strongly recommended that the password be changed after the initial setup to prevent unauthorized access.
Username – Admin
Password – 1234
For additional information on adjusting the settings of your internet browser contact your system administrator or go to openeye.net/support.
Default Username and Password
The username and password are case sensitive. It is strongly recommended that the password be changed after the initial setup to prevent unauthorized access.
Username – Admin
Password – 1234
Power
The CM-611 and CM-711 use Power over Ethernet (PoE). When using PoE, make sure the
Power Sourcing Equipment (PSE) is in use in the network.
Power Source Operational Temperature Range
PoE 14˚F~122˚F (-10˚C~50˚C)
Assigning an IP Address
OpenEye IP cameras come with the default IP address 192.168.0.250. To reset the IP
address, use the OpenEye Network Camera Manager application to set a new static IP, or use
DHCP.
1. Open the Network Camera Manager application.
2. Click Find Devices, and then double-click your
camera.
3. Click Network Setup.
4. Select Static IP and type the new IP address and other
network information in the appropriate boxes.
- or -
Select DHCP.
5. Click Apply.
6. Click OK to acknowledge the change.
7. After one minute, click Find Devices to search for all
connected IP devices.
8. Double-click the camera, and then click Browse.
9. Type the Username and Password to access the
camera.
23221 E Knox Ave
Liberty Lake, WA 99019
1.888.542.1103
Copyright ©2013 OpenEye. All Rights Reserved. Information contained in this document is subject to change without prior
notice. OpenEye does its best to provide accurate information but cannot be held responsible for typos or mistakes.
31094AB
Loading...