OpenEye CM-150 User Manual
Tamper Resistant
Indoor Mini Dome
Quick Installation Manual
model no
Please carefully read these instructions before using this product.
Save this manual for future use.
CM-150
CM-159
28395AC
General Specifications
Model No.
Lens Focal Length
Type / Format
Scanning Element
Effective Picture Element
Image Picture Element
Imaging DSP
Resolution (TV lines)
Minimum Illumination
S/N Ratio
Back Light Compensation
Exposure Control
Sync System
Gamma Compensation
Video Output
White Balance
Auto White Balance Range
Power Range
Power Consumption
Operating T emperature
Storage T emperature
2:1 Interlace
H15.734KHz / V :59.9Hz
768(H) x 494(V)
1/3” Sony SuperHAD CCD (Interline)
Sony SS-11X
1.2 Lux @ F1.6 (50 IRE)
Central Area for DC IRIS Lens
DC Type Auto IRIS Control
1.0Vpp, 75Ω Unbalanced
Automatic White Balance
2500K – 9700K
DC 12V ±10%
1.8W (Max)
-10°C ~ +50°C
-20°C ~ +60°C
CM-159CM-150
9mm~22mm4mm~9mm
NTSC
500
48dB
INT
0.45
Camera Adjustments
Lens Specifications
Focal Length
F-No.
Iris Range
Minimum Object Distance
Diagonal
Field Of View
BLC
GC-UP
A
Low Light Chroma
Suppression
Horizontal
Vertical
4mm~9mm
F1.6
F1.6~F2.4
50cm
92.8º~39.4º
71.0º~31.6º
51.6º~23.6º
9mm~22mm
F1.8~F360
39.0º~17.6º
30.7º~14.1º
22.7º~10.6º
ON/OFF
ON/OFF
AUTO
F1.8
15cm(6”)
Hardware Kit Contents
• 1/2” Rubber Grommet
• 3/4” Rubber Grommet
• Screw Pack
• Torx Driver
• Quick Install Adaptor
• Wire-Ended Power Adaptor Lead
Regulatory Compliance
Emissions
Immunity
FCC COMPLIANCE:
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in as residential installation. This equipment
generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try \to correct the interference by one or
more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced Radio/TV technician for help.
CISPR 22 WARNING:
This is a Class B product. In a domestic environment this product
may cause radio interference in which case the user may be required
to take adequate measures.
POWER SUPPLY REQUIREMENTS:
For use with listed Audio/Video product and only connected to 15W
or less power supply.
*Power supply should be a NEC Class 2 / LPS Supply.
EQUIPMENT MODIFICATION CAUTION:
Equipment changes or modifications not expressly approved by
seller, the party responsible for FCC compliance, could void the
user’s authority to operate the equipment and could create a
hazardous condition.
This class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme
NMB-003 du Canada.
FCC part 15 Class B
CE: EN55011
ICES-003
EN55022
CISPR 11
CISPR22
ANSI C63.4
EN50130-4
CE:
RoHS
Function Control Dip Switches
Switch 1
Switch 2
Back Light Compensation
OFF
Auto Gain Control
OFF
(Normal Mode)
Vari-Focal Lens
A
ON
ON
(T
urbo Mode)
A1
A2
Focus AdjusterA1 :
Field of View
A2 :
Adjustment
A3 : Function Control
Dip Switches
AI Level
A4 :
Adjustment*
Template
Surface Mount (Wall or Ceiling)
Using the Quick Install Adaptor: Using screws:
Create a 1.5” (38mm) hole in the mounting surface as
indicated by T2. The hole can also be used for cable access.
Cable access:
To thread the cables through the mounting surface, cut a 3/4”
(19mm) hole as indicated by the Cable Access markings
inside T2.
Drill four holes at template positions T1 and use the screws
and anchors provided with the camera if they are appropriate
for the mounting surface.
When mounting the camera on a surface with the provided
screws, use one of the side knock-outs, as indicated on the
template, for cable entry.
Side Knock-out
T1
T2
T1
Cable Access
T1
Side Knock-out
A3
A4
* AI Level Adjustment is factory set;
it should not require adjustment.
Side Knock-out
T1
Side Knock-out
Installation
1
2
Dome Base
TILT 90°
3
Camera Module
4
Camera Liner
5
Dome Cover
T1
T1
ROTATE 360°
T2
T1
PAN 360°
T1
1. Prepare Surface for Installation
Use the included template to mark and prepare the mounting area.
To mount the base, fist remove the camera module by gently
pulling down the tabs that hold the camera module in place (see
image right) and remove the camera module. To re-assemble the
camera, gently pull down the tabs and insert the camera module.
A
Mounting Surface
Cable Notch
Side
Knock-outs
3/4”
Rubber Grommet
Cable Notch
A. Using the Base Mounting Holes:
When mounting the dome on a ceiling or wall using screws, first
knock-out the screw holes that correspond to the template marks T1.
This can be done using a Phillips screwdriver.
Push the cables through the dome base and 3/4” rubber grommet.
Make sure the grommet is properly installed to prevent dust penetration. The cables may be routed through the mounting surface if an
appropriate hole is cut using the template markings T2. If using the
side knock-out, make sure the video cables are properly arranged in
the cable notch and exit the side knock-out without being crushed.
PULL
Pull the tab and remove the camera module
B. Using the Quick Install Adaptor (Optional):
Mount with the Dome Base
Video-Power Cables
B
1/2” Rubber Grommet
Mounting Surface
When mounting the dome on a ceiling using the quick
install adapter, use the template to cut a hole on the
T2 markings.
Insert the adapter into the hole and use the screws to
adjust the position of the two locking arms on the
adapter, securing it to the mounting surface.
Push the cables through
the 1/2” rubber grommet
and the adapter. Make
sure the grommet is
properly installed on the
quick install adapter to
prevent dust penetration.
Install Quick Install Adaptor on indoor ceiling
Locking Arms
Quick Install Adaptor
C. Mount on a Single Gang Box (US):
Mount with the Quick Install Adaptor
C
Mount on a pre-installed US Single Gang Box
T1
3/4”
T1
Rubber
Grommet
Single Gang BoxDome Base
When mounting the camera to a single gang box, carefully remove the
screws from the gang box. Insert the 3/4” rubber grommet into the
camera base to prevent dust penetration, then push the cables through
the dome base and rubber grommet.
Mount the camera base on the gang box using the two screws
removed previously. Tighten the screws to secure the base.
Removing the dome cover and camera liner
Gently turn the dome cover counter-clockwise to unlock and remove
from the dome base. Remove the camera liner by gently pulling the
liner free of the four notches in the camera base.
Opening a side knock-out
Open a side knock-out on the dome base to the size
required to allow cable entry.
Template
2. Mount the Dome Enclosure
Use the base mounting holes to install the dome base
to a wall or ceiling with screws.
Note: When using the Quick Install Adapter, reassemble the dome and mount the whole camera
dome onto the adapter.
3. Install Camera Module
Push the video power cables through the opening
Feed the pre-connected video power cables through
the appropriate opening. Make sure the cable is
properly positioned and exits out of the side knock-out
(if required).
Adjust the camera position
Adjust the camera position by rotating and panning the
camera module. The focus and range of the lens can
be adjusted on some models. See the Camera
Adjustments section.
4. Install the Camera Liner
Carefully fit the camera liner
over the camera until it
snaps in place. Do not
obstruct the camera lens.
5. Replace the Dome Cover
Install the dome liner on the camera module
Replace the dome cover and rotate it clockwise.
6. Tighten the Tamper proof Screw
Use the supplied torx driver
and the tamper-proof screw to
secure the dome cover.
Tighten tamper-proof screw
Tamper-proof Screw
Loading...