OpenEye 960H IR User Manual

960H IR

Outdoor Dome Camera

Camera Installation & Conguration

Model no: CM-P317R

Please carefully read these instructions before using this product.

Save this document for future use.

31376AC

Regulatory Compliance

Emissions FCC part 15, subpart B, Class A
CE: EN61000-6-4:2007

Immunity CE: EN60130-4:1995 + A1:1998 + A2:2003

FCC COMPLIANCE

This product has been tested and found to comply with the limits for a Class A
digital device pursuant to Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. The product generates, uses, and can
radiate radio frequency energy, and, if not installed and used in accordance with

the manufacturer’s instruction manual, may cause harmful interference with radio

communications. Operation of this product in a residential area is likely to cause
harmful interference, in which case you will be required to correct the interference
at your own expense.

This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference
that may cause undesired operation.

These limits are designed to provide reasonable protection against harmful
interference in a non-residential installation. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference with the radio or television reception, which can be deter­mined by turning the equipment off and on, you are encouraged to try to correct
the interference by one or more of the following measures:

1. Reorient or relocate the antenna of the radio/television receiver.

2. Increase the separation between this equipment and the radio/television
receiver.

3. Plug the equipment into a different outlet so that the equipment and the
radio/television receiver are on different power mains branch circuits.

4. Consult the dealer or an experienced radio/television technician for
additional suggestions.

General Specications

Model No. CM-P317R (Rev B)

Image Sensor 1/3” Sony CCD

IP Rating IP67 (Outdoor)

Type / Format NTSC

Wide Dynamic Range Sony True WDR

Minimum Illumination Color: 0.15 Lux

Day / Night True Day / Night (IR Cut Filter)

Resolution 700TVL

Service Monitor Jack Yes

S/N Ratio >52dB (AGC Off)

Focal Length 2.8 ~ 12 mm

Iris Control Auto-Iris

Synchronization Internal / Line Lock

Video Output 1.0 Vpp 75Ω BNC Unbalanced

White Balance AWB, ATW, Manual

Auto White Balance Range 1800K ~ 10500K

Backlight Compensation HLC, BLC, Off

Auto Gain Control Yes, 6~44dB

Operating Temperature

Heater Yes

Power Consumption 7.2W (IR LED Engaged)

Input Voltage 12vDC / 24vAC

Weight 1.8 lbs (0.82kg)

Dimensions Ø: 5.925” (150.5mm) x H: 5.13” (130.5mm)

Housing / Dome Cover White / Clear

Precaution

• Do not attempt to dismantle the camera module mounted
within the dome. There are no user serviceable parts
in the camera module. Refer servicing to a qualied
professional.

• Handle the camera with care. Do not abuse the camera.
Avoid striking or shaking it. Improper handling and
storage could damage the camera.

• Do not operate the camera beyond its temperature
or power source rating. Refer to the environmental
information provided in this document.

Features

• 700TVL Resolution

• Digital Noise Reduction

• 3-axis camera

• IP67-rated

• Wide Dynamic Range

• True Day/Night

• 24IR LEDs

B/W: 0.05 Lux

(@ 40IRE)

-49˚~122˚F (-45˚~50˚C)

Box Contents

• Screws (x3)

• Washers (x3)

• Torx security tool

• Service monitor cable

Dimensions

23221 E Knox Ave
Liberty Lake, WA 99019

1.888.542.1103
www.openeye.net

Installation

Using a Pole Mount

1. Remove the screw on the bottom of the camera
housing.

2. Open the dome cover.

3. Remove the tap cover and insert cables.

4. Apply teon tape to the threaded portion of the pole
mount. (Use of teon tape is necessary for water
resistence in outdoor applications).

5. Screw the pole mount into the base of the camera.

Camera Installation

1. Use the supplied screws to mount the camera on a wall
or ceiling.

2. If your camera uses a varifo­cal lense, adjust the lens
by opening the LED cover.
Turn the Tele-Wide knob to
adjust the eld of view. Turn
the Near-Far knob to set the
focus.

3. Once the camera is mounted

to the desired surface and is
focused correctly, re-assemble

the camera housing.

Adjusting the Camera Angle

1. To adjust the pan, the camera xture left or right within a
range of -160º ~ 190º.

2. To adjust the tilt, grasp the LED cover and adjust the
direction up or down within a range of 6º ~ 90º.

3. To adjust the vertical orientation, rotate the camera
holder within a range of -178º ~ 178º.

Camera OSD Menu

LENS
SELECT

EXPO­SURE

WHITE
BALANCE

DAY &

NIGHT

MANUAL

DC

PRESETS *Preset mode for common application to

WDR LOW WDR allows you to

BLC OFF

AGC CUSTOM

SENSE-UPEnable the SENSE-UP function and

FLICKER­LESS

ATW Automatic White Balance

AWC Find optimal white bal-

MANUAL R/B Adjust red or blue levels

AUTO INPUT

COLOR Image is always dis-

B/W Image is always dis-

speed up installation

CUSTOM User setting value

INDOOR For indoor

WINDOW Maximizing WDR function

OUT-

DOOR

NORMAL

MEDIUM

HIGH

ON

LOW (24)

MEDIUM

(30)

HIGH (36)

select level

OFF

AUTO For use in low light

MANUAL Select between 2X and

OFF Optimized mode for

CRR

CRR2

KELVIN Adjust color temp.

DELAY

For outdoor

clearly view a subject that
is backlight with bright
light.

situations, between 2X
and 64X)

64X

icker. If CRR is selected,

AWC mode will not be
available in the White

Balance menu.

ance with use of white

paper in eld of view.

The camera automatically
detects light levels and
sets mode accordingly.

played in color

played in black and white

IMAGE
ADJUST

MOTION** OFF No motion detection

PRIVACY OFF No privacy mask function

GAMMA 25 ~ 45 ~

SHARP-

NESS

COLOR
GAIN

FLIP OFF

ZOOM ON Max 4X Zoom

ON AREA

ON MASK

100

MIN ~
MAX

-8 ~ 0 ~ 8 Default: 0

HORZ Horizontal ip

VERT Vertical ip

BOTH Horizontal and vertical ip

OFF Normal Image (no zoom)

SELECT

AREA
1 ~ 4

1-12

MASK
COLOR

Default: 45

Default: MAX

PAN, TILT: Zoomed
image can be moved

horizontally and vertically

Select up to 4 motion

detection areas

• Adjust position and

size of motion detec­tion area

• Press ENTER to

move the motion

area setting section.
Press ENTER again
to change the mask

color

• When mask is white,
you can move the

mask up, down, left,
and right

• When the mask is

green and red, you
can adjust the mask

size

• Press ENTER for
a few seconds to

escape

• Congure up to 12
privacy masks

• Press SET to open
privacy mask settings.
Press SET again to
change the mask

color

• When mask is white,
black, or red, it can be

moved up, down, left,
and right

• When mask is blue,

you can adjust the

size

• Press SET for a few

seconds to escape

Select the mask

color (WHITE, RED, OR
BLACK)

FUNC­TION
SETUP

SYNC INT Internal sync with 12V

RS-485
SETUP**

CAMERA
ID SETUP

LL External sync with 24V

CAMERA # ID setting for RS-485

ID DIS-

PLAY

CAMERA IDChange the camera ID

ID

POSITION

V-PHASE Phase controllable at

communication (1 ~ 256)

Display the camera ID on

the screen

Select the position to
display the ID on the

screen

Power

AC power

24V AC

Function Setting

1. Push the lever to access the menu and conrm selec­tion. Push the lever for one second to open or close the
menu. Use the lever to return to the previous menu from
motion detection or privacy mask setting sections.

2. Push the lever up to move the cursor up.

3. Push the lever down to move the cursor down.

4. Push the lever left to move the cursor left.

5. Push the lever right to move the cursor right.

6. Plug a test monitor into the optional EXT-VIDEO termi­nal to view menu screens during installation.

7. Adjust the LED light level with the screw.

**MOTION and RS-485 SETUP
are not supported by OpenEye