OpenEye 200 Installation Manual
A
Dome base
Regulatory Compliance
Emissions
Immunity
Safety
FCC COMPLIANCE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in as residential
installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try \to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced Radio/TV technician for help.
CISPR 22 WARNING:
This is a Class B product. In a domestic environment this product may cause radio interference in which case the user
may be required to take adequate measures.
POWER SUPPLY REQUIREMENTS:
For use with listed Audio/Video product and only connected to 15W or less power supply.
*Power supply should be a NEC Class 2 / LPS Supply.
EQUIPMENT MODIFICATION CAUTION:
Equipment changes or modifications not expressly approved by the manufacturer, the party responsible for FCC
compliance, could void the user’s authority to operate the equipment and could create a hazardous condition.
This class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
FCC part 15 Class B
CE: EN55011
ICES-003
EN55022
CISPR 11
CISPR22
ANSI C63.4
CE: EN50130-4
CSA C22.2
RoHS
B
Locking arms
C
C3
C2
B1
C3
C2
C1
B1
Loosen screws, but not remove
them,to first extend the locking arms.
Then tighten the screws sufficiently to
compress the arms to adjust to the
mounting surface; however, DO NOT
OVERTIGHTEN.
C2
C3
C1: Threaded base
C2: Screw access holes
C3: Side knock-outs
Precautions
• Do not attempt to disassemble the camera module mounting within the dome. There are no user
serviceable parts within the camera module. Refer servicing to qualified service personnel.
• Handle the camera with care. Avoid dropping or shaking it. Improper handling or storage could
damage the camera.
• Regardless of whether the camera is in use or not, never face it toward the sun. Use caution when
operating the camera in the vicinity of spotlights or other bright lights and light reflecting objects.
• Do not operate the camera beyond its temperature, humidity, or power source ratings. Please refer to
the environmental information provided on the Camera Setup sheet
Hardware Kit Contents
• 1/2” Rubber Grommet
• 3/4” Rubber Grommet
• Screw Pack
• Torx Driver
• Quick Install Adaptor
• Wire-Ended Power Adaptor Lead
Template
Surface Mount (In a wall or ceiling)
Using Quick Install Adaptor: Cut a 1.3” (35 mm)
diameter hole in the mounting surface as indicated
by “T5”.
Using Screws: Use a ¼” (7.5 mm) drill bit and drill
three holes at the template positions “D5” and insert
a wall anchor in each hole. Use three D5 screws.
Cable Access
The cables are threaded through the base knockout
(shown in fig C1). The base is threaded for use with the
quick install adapter.
When mounting the dome on a surface with the three
D5 screws, use one of the side knock-outs as
indicated by C3 shown in fig C for cable entry.
See “Installing the dome enclosure” for instructions on
how to drill a hole on the side knock-out.
Tamper Resistant Indoor
Dome Camera
Camera Installation
model no.
Please carefully read these instructions before using this product.
CM-201
CM-205
CM-205-L9
CM-215
Save this manual for future use.
27789AG
D5
T5
D5
D5
D
D4
D1: Dome base
D2: Camera liner
D3: Dome cover
D4: Notches (on both sides)
E
Rotate and tilt the camera
base to the required position.
D1
D2
D3
Installing the Dome Enclosure
1. Remove the dome cover and the camera liner
Gently turn the dome cover counter-clockwise to unlock and pull free of the dome base. Remove
the camera liner by gently pulling it free of the two notches (D4) in the camera base (see fig D).
2. Use the template to mark-out and prepare the mounting area
When mounting the dome to a ceiling or wall using screws, first knock out the screw access holes
(C2) that correspond to the template marks “D5”. This can be done by using a cross-point
screwdriver. When mounting the dome to a ceiling using the quick install adaptor, use the
template to cut a hole as the circle marked “T5” with a hole cutter.
3. Open the required knock-out panel
Use a sharp knife or side cutter pliers to cut one of the side knock-outs (C3) to the size required to
allow cable entry. Be careful not to hurt yourself or damage the camera when using knives and
side cutter pliers.
4. Mount the dome enclosure
Using one of the mounting schemes discussed on the
other side of this sheet (Methods for mounting the enclosure), fix the dome enclosure in place.
5. Connect the wiring
Feed the pre-connected main lead (that feeds into the
connections G1 and G2) through the appropriate point and
connect it to your video out and power in cables. A service
jack socket is also provided for temporary video connection
when focusing the camera, using an optional service cable
(CA-MON/BNC).
6. Adjust the camera position
You can adjust the focusing position by rotating and panning the camera base (see fig E).
7. Install the camera liner
Carefully fit the camera liner (F1) over the camera base so that it snaps into place as shown in fig.
F and does not obstruct the camera lens.
8. Replace the dome cover
a. Install 3/4” cable entry sealing plug (G3) on the dome base.
b. Push the cables (G1 and G2) through the dome base and 3/4” cable entry sealing plug (G3),
make sure the sealing plug is properly installed on the base.
c. Replace the dome cover (F2) and rotate to close it as shown in fig F. Use the supplied T6 screw
to secure the whole enclosure (see fig. G)
9. Using the quick install adaptor see figure H
a. Install 1/2” cable entry sealing plug (H2) on quick install adaptor (H1). Push the quick install
adaptor into the appropriate cut out hole.
b. Use the screws to adjust the position of the two locking arms (B1) on the quick install adaptor to
adjust to the mounting surface.
c. Push the cables through the opening (H1) and 1/2” cable entry sealing plug (H2), make sure the
sealing plug is properly installed on the adaptor;
d. Thread the dome onto the quick install adaptor. This takes about 1½ turns. DO NOT OVERTIGHTEN.
Service jack
socket
F
360º
rotate
83º
tilt
G
G3
G1: Video Output Connector
G2: Power Input Connector
G3: Cable entry sealing plug (3/4”)
H
T6 screw
G2
G1
Push the camera liner
up to the base until it
clicks into place.
E1
F1
E2
F2
H1
H2
F1: Camera liner
F2: Dome cover
H1: Quick install adaptor
H2: Cable entry sealing plug (1/2”)
Loading...