O²-Light
A. Assembly
Status
Growth
Reading
Reading minus
ON
High
Low
OFF
ON
High
Low
OFF
(Growth Light)
(Hi Brightness)
(Lo Brightness)
Time(On/Off)
LED: 16H/8H Pump: 24 cycles/ day
LED: 24H/0H Pump: 12 cycles/ day
LED: 24H/0H Pump: 12 cycles/ day
24H/0H
18H/6H
10H/14H
0H/24H
48 cycles/ day
36 cycles/ day
1 cycle/ 5day
0 cycle/ day
( 10mins / cycle )
( 20Secs / cycle )
( 20Secs / cycle )
( 10mins/ cycle )
( 10mins/ cycle )
( 10mins/ cycle )
Fuction
Auto
LED
Pump
Light
* 1. Push the button on the control box to switch the mode * 2. you can reset the product timeline by pushing the LED button for 2 sec.
Chart I: Control Box Mode
Planting Partition x 2
Grow Kit Accessories
0.7 gallons（2.7L）
Rotate over 30 degrees
Growth mode Reading mode
* Fan on when LED on , more air circulation will make plants grow better
Left/ Right
180 degrees
90 degrees
60 degrees
Horizontal
Front
Back
UP
Down
1. Small Filter Bag x20pcs 2. Large Filter Bag x10pcs
Thank you for purchasing OPCOM Farm O²-Light, the indoor hydroponics growing system. It is designed with
easy to use and efficient growth by one-touch AUTO mode. It holds up to (2”pot) 16 plants capacity. Read the
quick guide carefully before setting it up. For detailed user guide video, please scan the QR code or visit
O²-Light page at http://www.opcomfarm.com/O2light
A1. Remove all the parts from box and check all the accessories.
A2. Easy Set Up: Please follow below steps to set up
A3. Reading Adjustment.
1
44
6
2
☑
Please read and follow every steps to avoid any malfunction.
5
2
3
4
Install the planting partition(accommodate 1”, 2”, 3”,
4” pot sizes per your needs)
Connect power adapter to the unit.
Add 0.7 gallons(2.7 Liter) water to the unit.
Ensure air tube immersed into the water.Always keep
water up the water level mark line.
5
6
Turn on the power and test the unit.
Auto Switch Mode : O²-Light is not only a hydroponics
system but also a table lamp, you can switch between
grow light and reading light by simply rotating lamp
arm or pressing auto button to show “Green”.
Position lamp’s arm and adjust the angle.
45 degrees 90 degrees
B. Seedling
Adapter
INPUT: 100-240V~ 50/60Hz
OUTPUT: DC12V 3A
C. Planting
C1. Planting Process: Buy plants from local stores
1
Choose a suitable filter bag size for 2", 3", 4" pot, put it into the
filter bag and tie the strings(Fig1), Then put the plants into
tank(Fig2)
C2. Flower Selection
Rainbow Tree Chlorophytum Lucky Bamboo Chrysanthemum Snake Plant
Formaldehyde Clean
White Bunny Ears Golden barrel Mottled Spurge Turk's Cap Cactus Golden ball cactus
Trichloroethylene Clean
Dot plant Wax Plant Dragon tree Barberton daisy Dragon tree
Carbon dioxide & Formaldehyde Clean
Dumbcane Tuberous Sword Fern Flaming lily Evergreen Pteris cretica
Xylene Clean
Ivy Peace Lilies Parlour Palm
Aloe Spiral-leaved croton
Carbon Monoxide Clean
1.Grow kit
a. Seedling kit :
b.Nourishment:
Manual
Warranty Card Quick Guide Manual
Quick Guide Manual
O²-Light
Seedling Tray(ST-30) x1pcs
(342*110*126mm)
Grow Sponge 2x30pk
(OASS16K For Basil)
NT-Starter x24pcs
(OAMS27K for O
2
-Light)
Grow Sponge 2x30pk
(OASS15K For Lemon Balm)
Free combination
3
Free combination：You can mix different size of pots and sponges
into the growing hole of O²-Light.
4"2" 3"
(Fig1) (Fig2)
2”x 8pcs
1Line
4”x 4pcs
1Line
3”x 5pcs
1Line
B2.Young plant stage
1. In each sponge, keep the strongest and thicker one and remove others.
2. Add 0.7 gallons(2.7 Liter) water to the tank.
3. Add 1 pack of NT-Starter to the product.
4. During young plant stage (around 2 inches), turn on LED and Pump . Please refer to the ChartII.
5. Adjust LED light angle to let the light cover on all plants.
B3. Growing Stage
* When water is less than 1/2 tank full, change to new water with new NT-starter.
B2. Young Plant
1. When plants grow to 3-4 inches height, switch to Auto Mode(Growth), refer to Chart I & II.
2. Harvest the larger plants for consumption and keep smaller plants growing.
* To save time, sow the new seeds in sprout tray one week before you restart the planting process.
B1. Sprout stage
1. Add water into the seedling tray, up to the water (red) line.(Fig1)
2. Open Grow Sponge package, Put the sponge into water of seedling tray(make sure the front side with the
seed label is up),press the sponge into water 5 seconds and let the sponge absorb water completely.(Fig1)
3. Place the seedling tray with cover in the shade or cover it with black cloth(to block light).(Fig2)
4. Spray water to Sponges and keep them wet everyday.
5.During 7 days, find the sprouted one in the tray; pick it out, and move it into product (make sure the
sponges line up with the black dot on the partition)(Fig3) and to next stage: B2. Young Plant Stage.
6. Discard unsprouted sponge after regular germination time.
* Different plant may have different germination time, please check it before plant.
Chart II: Plant Stage
Basil, Lemon Balm
Sprout Stage
Young plant stage
Growing Stage
Planting Time
Day 0~7
Day 3~14
After Day 14
LED Mode
N/A
ON
Auto
Pump Mode
N/A
ON
Auto
Notes
The sponge is fully wetin seedling tray.
* Please keep the seedling sponge package in refrigerator if you don’t use it.
* For your expected plant amout, you can refer to the sprout rate of 1st planting cycle.
* If you need more planting information, please vist to www.opcomfarm.com to read “Plant Q&A”.
Nourishment
N/A
NT-Starter
NT-Starter
T (℃)
20℃- 25℃
15℃- 30℃
15℃- 30℃
RH
80%
45%-70%
45%-70%
EC
0.5-1.0
1.0-2.0
1.0-2.0
pH
5.5-6.5
5.5-6.5
5.5-6.5
(Fig3)
(Fig2)
(Fig1)
This side up!
2” Pots x 16pcs
2
(Fig1) (Fig2) (Fig3)
(Fig2)
Soil FSoil Free: Remove pot(Fig1) and put into filter bag(Fig2) and then move
to the product(Fig3).
Water Level
Water Level
44
H. Q&A
F. Maintenance
G. Troubleshooting
Checkpoints / Solution
Make sure all power cables are connected.
Power button is ON.
Make sure LED status is ON
If it is on HI or LOW mode, there is an off time setting for lamp, during 24-hour cycle.
Make sure Pump status is working.
If it is on HI or LOW mode, there is an off time setting for lamp, during 24-hour cycle.
Ensure the air tube connected with the plastic air port.
Control Box is designed with Auto, HI and LOW modes, which turn the lamps and the pump on
and off at certain intervals. It simulates an outdoor daily cycle to offer the best growing condition
Issue
Lamps not on
Air tube has
no bubble
The lamp/ pump
stop after hours
Answer
No, Just swith between growth and Reading+ / Reading- mode each time.
You can adjust the planting partition to fit the pots size, as you like.
Question
When I read, can I use growing mode?
How to use planting partition?
www.opcomfarm.com
For more information, please visit
Quick Guide Manual
Ver.: 180322
O²-Light
Table Garden
E. Optional Accessories (Grow from seeds hydroponically)
1. Pod Stick : 3x30PK
D. Sprouts and Microgreens.
2. Growing Sponge D65
Day 7-10
Green sprout
Day 0 Day 1
1. Before your next seedling, take advantage of the seedling tray for sprouts and microgreens it takes 7-10 days to harvest.
2. Put seeds in warm water(recommeded temperature is 35
, not over 40 ) for 24 hours.
3. Wet and put the paper towels into the tray.
4. Place the seedling tray with cover in the shade or cover it with black cloth.
5. After germination, during the growing stage, keep green sprout under the light and white sprout in the shade or cover it
with black cloth; Around 7-10 days, you can harvest.
White sprout
F1. Add Water
1. Add water when water is less than 1/2 tank (you may also add flower nutrient if you obtain it)
F2. Change Water
1. Change new water with new NT-Starter when water is less than 1/2 tank.
2. When you restart the new cycle, please wipe off the water tank.
3. Change new water with different nutrient for different flower/plant.
3. OPCOM Wave Clip
F1709048
P17103005
P17092807
F1709053
Loading...