OnvianTech IPC4300ADH User Manual

IP camera tester

USER MANUAL

（IPC1.03）

Thank you for purchasing the IP camera tester. Please read the manual before using the IP camera

tester and use properly.

For using the IP camera tester safely, please first read the「Safety Information」carefully in the

manual.

The manual should be kept well in case of reference. Keep the S/N label for after-sale service within warranty period. Product without S/N label will

be charged for repair service.

If there is any question or problem while using the IP camera tester, or damages occurred on the

product, please contact our technical Department.

Content

Safety information

------------------------------------------ 1

IP Camera Tester Introduction

----------------------------- 2

2.1 General --------------------------------------------------- 2

2.2 Features -------------------------------------------------- 3

2.3 Function -------------------------------------------------- 5

2.4Packing list----------------------------------------------- 12

2.5 Function introduction： ----------------------------------- 13

Operation

---------------------------------------------------- 17

3.1 Installing the Battery ------------------------------------ 17

3.2 Instrument connection ------------------------------------- 18

3.2.1 IP camera connection ------------------------------- 18

3.2.2 Analog camera test --------------------------------- 19

3.3.3 SDI Camera Test ------------------------------------ 20

3.3 OSD menu ------------------------------------------------- 21

3.3.1 Video monitor test (PTZ control) ------------------- 23

3.3.2 Color-bar generator (TV OUT) ----------------------- 33

3.3.3 ONVIF ---------------------------------------------- 34

3.3.4 IP camera test ------------------------------------- 42

3.3.5 SDI Camera Test(*optional) ------------------------- 45

3.3.6 IP address scan ------------------------------------ 47

3.3.7 PING Test ------------------------------------------ 48

3.3.8 Cable test ----------------------------------------- 49

3.3.9 Cable tracer *（optional ） ------------------------- 49

3.3.10 Port finder --------------------------------------- 51

3.3.11 Data monitor -------------------------------------- 52

3.3.12 Optical power meter （Optional ） ------------------ 52

3.3.13 Visual Fault Locator（optional） ------------------- 54

3.3.14 Digital Multi-meter *（optional ） ----------------- 56

3.3.15 Video Player -------------------------------------- 61

3.3.16 Music player -------------------------------------- 62

3.3.17 LED lamp (Flashlight) ----------------------------- 63

3.3.18 PoE/PSE Voltage test ------------------------------ 63

3.3.19 TDR cable test *（optional） ---------------------- 64

3.3.20 Calculator ---------------------------------------- 67

3.3.21 Browser ------------------------------------------- 67

3.3.22 IP camera viewer ---------------------------------- 68

3.3.23 PoE power / DC12V 2A and DC 5V 2A USB power output 69

3.3.24 Application tools --------------------------------- 71

3.3.25 APPS Tools ---------------------------------------- 77

3.3.26 System Set ---------------------------------------- 79

3.3.27 Update -------------------------------------------- 81

3.4 HDMI output----------------------------------------------- 82

3.5 PoE power output ------------------------------------------ 82

3.6 DC12V 2A power output ------------------------------------- 83

3.7 USB 5V 2A power output ------------------------------------ 84

3.8 Audio test------------------------------------------------ 85

Specifications

---------------------------------------------- 86

4.1 General Specifications ------------------------------------ 86

4.2 Multi-meter specifications -------------------------------- 88

4.3 Optical power meter specifications ------------------------ 90

4.4 Visual fault locator specifications ----------------------- 91

page

1. Safety information

The tester is intended to use in compliance with the local rules of the electrical usage and avoid to apply at the places which are inapplicable for the use of electrics such as hospital, gas station etc.

◆ To prevent the functional decline or failure, the product should not be sprinkled or damped.

◆ The exposed part of the tester should not be touched by the dust and liquid.

◆ During transportation and use, it is highly recommended to avoid the violent collision and vibration

of the tester, lest damaging components and causing failure.

◆Don’t leave the tester alone while charging and recharging. If the battery is found severely hot, the tester should be powered off from the electric source at once. The tester should not be charged over 8 hours.

◆ Don’t use the tester where the humidity is high. Once the tester is damp, power off immediately and move away other connected cables.

◆ The tester should not be used in the environment with the flammable gas.

◆ Do not disassemble the instrument since no component inside can be repaired by the user. If the

disassembly is necessary indeed, please contact with the technician of our company.

◆ The instrument should not be used under the environment with strong electromagnetic interference.

◆ Don’t touch the tester with wet hands or waterish things.

◆ Don’t use the detergent to clean and the dry cloth is suggested to use. If the dirt is not easy to

remove, the soft cloth with water or neutral detergent can be used. But the cloth should be tweaked sufficiently.

About Digital Multi-meter

◆ Before using, you must select the right input jack, function and range.

◆ Never exceed the protection limit values indicated in specifications for each range of measurement.

◆When the tester is linked to a measurement circuit, do not touch unused terminals.

◆Do not measure voltage if the voltage on the terminals exceeds 660V above earth ground.

◆At the manual range, when the value scale to be measured is unknown beforehand, set the range

selector at the highest position.

◆Always be careful when working with voltages above 60V DC or 40V AC, keep fingers behind the probe barriers while measuring.

page

◆Never connect the meter with any voltage source while the function switch is in the current, resistance, capacitance, diode, continuity, otherwise it will damage the meter.

◆Never perform capacitance measurements unless the capacitor to be measured has been discharged fully.

◆Never measure any of resistance, capacitance, diode or continuity measurements on live circuits.

Visual laser sources

When you turn on visual laser sources, please don’t stare at it, or will damage to eyes

When not using it,Please turn it off and cover the protective cap

2. IP Camera Tester Introduction

2.1

General

The 4.3 inch touch screen IP camera tester is designed for maintenance and installation of both IP camera and analog camera as well as other security equipments , 800x600 resolution, It enable to display network HD camera and analog camera image in top quality. Support both ONVIF PTZ and analog PTZ control. The combination of touch screen and key buttons make the IP camera tester very user- friendly. Meanwhile the tester is also a very great tool for Ethernet network, cabling system and fiber optic communication etc. It can test PoE power voltage, PING, IP address searching etc. It can diagnose the location of the BNC and network cable’s short circuit and open circuit. By sending the audio signal, use the blue cable tracer tester to find the connected cable from messy cables. Test LAN cable or telephone cable’s type and the sequence of wires. Optical power meter and visual fault detector function, effective to solve the fiber optical transmission problem. digital multimeter, LED Lamp, DC 12V 2A power output etc. Its portability, user-friendly design and multi-functions make the IP camera tester become an essential tool for the installer or technicians, greatly improving the working efficiency and simplifying the installing and maintenance.

page

2.2 Features

 4.3inch 800×600 touch screen, easy to operate.

 ONVIF IP camera test

 Test some customized brands’s H.264/MPEG4/MJPEG IP cameras, such as Dahua,

HIKVISION,ACTI, etc. Customized service is available.

 Built in Wi-Fi ,can receive image from wireless camera, as well as ONVIF and customized IP

cameras.

 SDI Digital camera image display, record and screen snapshot * (Optional)  HDMI signal input,support1080P*(Optional)  HDMI signal output,support1080P

 Analog camera image display, Auto adapt and display the video format of NTSC/PAL  Support more than 30 protocols ,such as PELCO-P、PELCO-D、SAMSUNG etc  PEAK video signal level, SYNC signal level, Color burst chroma level measurement,test

video signal attenuation (Optional)*

 Video image magnification, to view the details, easy to use  Snapshot and save the current image as JPG file in the SD card, video record and playback.  LED Lamp, easy to operate at night

 Micro SD card moveable

 LCD screen brightness/contrast/color Saturation adjustable  Visual fault locator , to test fiber’s bending and breakage(Optional)*  Optical power meter ,test fiber loss and value (Optional)*  Digital Multi-meter , DC and AC voltage measurement, Resistance measurement(Optional)*  Enhanced Color bar generator, Video Generating, the PAL/NTSC multi-system color bar

video generator (Eight-system switchable, transmit/receive eight-system colorful images).

 Cable tracer, by sending the audio signal, enables the blue cable tracer tester to find the

connected cable from messy cables.

(Optional)*

 Ping test, PING is the most conventional network debugging tools; it is used for testing if the

page

connected IP camera or other network equipment’s Ethernet port is working normally and the IP address is correct.

 IP address scan, quickly search the connected IP camera or other network device’s IP address

 PoE voltage test,it can test the PoE voltage when the POE switch is supplying the POE power

to IP camera ,wireless AP etc

 TDR cable test,test cable length and short-circuit* (Optional)  Cable test , Test LAN cable or telephone cable,UTP cable etc ,cable type and the sequence of

wires will be displayed

 Support RS232/RS485,Rate 600 ～ 115200bps adjustable  PTZ protocol analysis, control protocol command displays to check RS485 transmission

whether is normal, easy to find the fault device  PTZ control. Pan/tilts the P/T unit, zooms in/out the lens, adjusts the focus, aperture and

sets and the preset position

 DC12V 2A output power for camera

 PoE 24W power output,supply temporary power for PoE camera  DC5V 2A power output,as a power bank

 Audio input and output, test and output the audio signal  7.4V 48.1Wh Battery energy display, Lithium Ion Polymer Battery can lasts 16 hours for normal

use after charging for 8 hours

“*”Sign means the function optional

page

2.3

Function

2.3.1 Touch screen and OSD menu

The IP camera tester combines with capacitive touch screen and key buttons. It is great improving the working efficiency and simplifying the installation and maintenance.. The user can be freely to move the function icons from the tester’s main menu to APPS tool file or move them back, to make the main menu look simple and clear.

2.3.2 WIFI

Built in WIFI, can receive wireless camera (ONVIF and customize camera) or network data etc.

2.3.3 IP camera test

The device is designed with ONVIF test, IP camera test, browser functions etc. It can display the image from the ip camera and change the IP address etc. 4.3inch 800×480 screen display, allows the user to view the image at larger angle. This is very helpful and convenient for the users to install the ip cameras at site. In ONVIF TOOL, it can display the image from ip camera and control the PTZ. Currently the IP camera tester only supports more than 30 brands’ IP cameras, such as ACTi、Dahua IPC-HFW2100P、 Hikvision,DS-2CD864-E13、Samsung SNZ-5200、Tiandy TD-NC9200S2、Kodak IPC120L、Honeywell HICC-2300T、Aipu-waton IP5000-BC-13MP/IRS06-13MP etc. OEM service is available. Users can send us the ip camera video management software for our engineers try to add the protocol to the tester.

2.3.4 SDI camera test （*optional）

SDI digital video surveillance testing, support720p 60fps / 1080p 30fps / 1080i 60fps digital camera image test and video image zoom, record, screen snapshot, Photo viewer and playback .

2.3.5

HDMI signal output

With HDMI output port, support 1080P 60fps resolution output, record and media files

playback .playback the recording and media files, and output them to HD TV monitor.

page

Meanwhile, the HDMI output can be used as SDI-HDMI convertor to output the SDI video to

the HD TV monitor.

2.3.6 Analog camera test

Display analog camera image ,4.3 inch 800×480 LCD screen display ,larger viewing angle ,more intuitively and easily to display the camera image quality. Support PAL/NTSC format.LCD screen backlight brightness adjustable, and analog video image brightness/contrast/color Saturation adjustable.

2.3.7 Video level meter*(optional)

The IP camera tester has adopted hardware high-speed sampling and processing technology, enables it

to achieve more accurate measurements in the video signal PEAK, SYNC level,

COLOR BURST chroma level

Video signal PEAK level: For PAL format , the video signal level is 1000±200mV

For NTSC format, the video signal level is 140±15IRE

If the level is too low, it will cause the image to dim and reduce dynamic range, but if the level is

too high, it will lead to virtual shadow and reduce the definition of the image.

SYNC level: by testing the amplitude of the video sync pulse to verify if the video level is correct and

the coaxial cable connectivity is good.

For PAL format, the SYNC level is 280 ± 35mV

For NTSC format, the SYNC level is 40 ± 5IRE

If the level is too low, it will cause the image to fracture or scroll, but if the level is too high, it will lead

to reduce the image’s color levels and dynamic range.

COLOR BURST chroma level: by testing the color burst level to estimate whether the coaxial cable is

the best to transmit the details and color.

For PAL format, the Chroma standard level is 280mV

page

For NTSC format, the Chroma standard level is 40 IRE

If the Chroma level is low or too low, the color will not bright, and some details on the iamge will lost

or get dark or white when the monitor receives the iamge.

If the Chroma level is too high, there will be spots on the image. If this occurs, it cannot get the clear

image with all the details. If the coaxial cable is too long, it will reduce the chroma level

2.3.8 PTZ controller

Display the input video images. Pan/tilt the P/T unit and zoom in/ out the image. Setup the controlling parameters like protocol, communication port, baud rate, PTZ ID, pan/tilt speed; set and call preset position.

2.3.9 Enhanced Color bar generator

The tester sends out the color bar by its BNC output to the monitor at the monitoring center. If the monitor receive the color bar, it means the video transmit channel works normally. Meanwhile on the basis of the received color bar, the monitoring center can judge if transmission has loss or interference. The tester can also send out the color bar by its BNC output, then receive and display the color bar by its BNC input to test on-site video transmission, such as video optical transmitter and receiver, video cables. The new function of sending the testing image can judge if the monitor receives the image well. The new color bar (red, green, blue, white, black) can test the monitor whether have white or black dot etc.

2.3.10 DC12V 2A/DC 5V 2A output power

Power the camera with DC12V (2A) power output from the tester. It is helpful for demo and testing when the power supply is not available. Built in DC5V2A power output,used as a power bank .

2.3.11 PoE power supply

Support PoE power 24W,High capacity 37Wh Lithium polymer battery, Provides temporary

page

power for the PoE network camera .

2.3.12 Audio testing

Test the audio input from pickup devices. Connect the tester and pickup device with the audio cable. Supports audio recording and audio output.

2.3.13 Enhanced Color bar generator

2.3.14 PTZ data analysis

Search the Control protocol code from Multifunction keyboard or DVR by RS485 /RS232 interface, test the PTZ control command data whether received anomaly and RS485/RS232 data transmission.

Screen displays 16 hexadecimal codes such as PELCO-P：A0 00（Add） xx xxxxxx AF xx PELCO-D：FF 01（Add）xx xxxxxxxx

2.3.15 Image magnification

Set image zoom, by x1, x2, x3, x4 10times ,can view and display the details .Support analog camera, ONVIF ,as well as some brands’ specified models, such as DaHua、Hikvision、ACTi、Samsung camera

2.3.16 Video screenshot

Capture the video image, and save the current video image in the SD card.

2.3.17 Record

page

Capture the video frames as JPEG file, and save the current video in the SD card.

2.3.18 Playback

Save video image and record files in the SD card. Storage file directory can be created according to the date

2.3.19 Cable tracer *(optional)

Send the specific signal, easy to find the connected cable from messy cables.

2.3.20 DHCP dynamic address assignment

Built in DHCP server, dynamic assign IP address for the IP camera or network device, meanwhile inquire and display the assigned IP address.

2.3.21 Access the dynamic IP address

The IP tester can directly access the dynamic IP address assigned from its DHCP server and used it as the tester’s IP address. It don’t need to manually setup.

2.3.22 Multi- segments IP Cameras Test

Support Multi- segment Static IP address setting,,can simultaneously test different segments IP network cameras

2.3.23 Network bandwidth testing

Network channel bandwidth test, need two IP camera testers to test, one as a transmitter, the

other as a receiver, Or install the testing software in the PC firstly, then work with one IPC tester to test the network channel bandwidth.

2.3.24 IP address scan

In digital IP surveillance applications, if IP camera’s IP address is not clear or forgotten; the device cannot be used .IP address scan can quickly search the connected IP camera or other network device’s IP address.

2.3.25 PING Test

PING is the most conventional network debugging tools; It is used for testing if the connected IP

page

camera or other network equipment’s Ethernet port is working normally and the IP address is correct.

2.3.26 Port Finder

The tester will send special signals to make the connected POE port flicker at special frequency, which will enable the installers to easily and quickly find the connected ethernet cable. This function can prevent mistakenly insertion or disconnection non-corresponding cable to artificially interrupt network connection.

2.3.27 PoE Test

It can test the PoE voltage when the POE switch is supplying the POE power to IP camera. It can clearly display the power+ and power- on the Ethernet cable pins, each cable pin’s voltage and the failure connection of cable pin series numbers.

2.3.28 Digital Multi-meter* (Optional)

The tester built in highly stable and reliable 33/4 digit (6600) digital multi-meter. It is used for the DC and AC voltage measurement, AC and DC current measurement, Resistance measurement, Continuity test, Diode measurements, Capacitance measurement, Auto/Manual measuring range switching, relative value measurement and locking. It is easy operation and professionally accurate.

2.3.29 Visual fault locator *(Optional)

Visual Fault Locator with 650nm wavelength can emit red laser sources to test multi-mode and single mode fiber’s bending and breakage, and Continuous light-emitting and 1HZ, 2Hz modulating light output.

It is indispensable tool in fiber project constructing, fiber net-work maintaining, optical

component manufacture and research.

2.3.30 Optical Power Meter *(Optional)

The IP camera tester adopts the most advanced handheld instrument specific integrated chip , achieve ultra-low power operation, with the 3.5 TFT-LCD High-definition screen display ,five wavelength calibration points 1625nm,1550nm ,1490nm , 1310nm , 1300nm , 850nm.Linear or nonlinear optical power display, it can measure the optical power value, and also be used for Relative measurement of optical fiber link loss. It is necessary tool for fibre-optic communication, cable television system and

page

security system maintenance.

2.3.31 LED lamp

It is useful for the user to install and maintain security system at night. Press button LED On/Off, easy operation.

2.3.32 OSD menu rotates in 180 angle

OSD menu can be rotated in 180 angle by manual setting. This function is very convenient for the user to upward the downside to connect the LAN cable and do the testing.

2.3.33 TDR cable length and short circuit measurement *(Optional)

TDR cable testing, accurately measure BNC cable, network cable, controls cable’s length and short-circuits location. It improves working efficiency.

2.3.34 FTP Server

The tester can start FTP Server function, the PC read SD card files from the cctv tester via network or WIFI, it does not need to pull out the SD card, and help user to more conveniently upgrade tester software and access files.

page

2.4Packing list

1). Tester

2). Adaptor DC12V 2A

3) Network cable tester

4) Polymer lithium ion battery (7.4V DC 5000mAh)

5). BNC cable

6). RS485 cable

7).SC,ST connector（Only for optical power meter）

8).Multi-meter test leads one pair of red and black (only for the Multi-meter models)

9). Output Power cable

10). Audio cable

11). TDR alligator clamp (only for TDR models)

12). Safety cord

13). Tool bag

14). Manual

15) 4G SD card

page

2.5

Function introduction

：

page

Press more than 2 seconds, turn on or off the device ,short press to turn on or off the menu display

Set key.

Menu key

Near focus: Focus the image nearby

Far focus: Focus the image faraway

TELE: zoom in the image

WIDE: zoom out the image

Open/set ,Confirm the setting of parameters, open or enlarge the aperture

Return/Close : Return or cancel while setting parameters of the menu, close or decrease the aperture

Upward, set function or add parameter. Tilt the PTZ upward

Rightward, select the parameter whose value will be changed. Add the value of the parameter. Pan the PTZ right

Confirm key

Leftward, select the parameter whose value will be changed

Downward, set function or reduce the value of the parameter. Tilt the PTZ downward

Snapshot

Video record

Open/set ,Confirm the setting of parameters, open or enlarge the aperture

Return/Close : Return or cancel while setting parameters of the menu, close or decrease the aperture

19 The power indicator: it lights green while the tester is powered on by the adapter 20 The data accepted indicator: it lights red while the data is being received

page

The RS485/RS232 data transmission indicator: it lights red while the data is being transmitted

The charge indicator: it lights red while the battery is being charged. As the charging is complete, the indicator turns off automatically

23 Multimeter interface

Top interface

page

Left interface Right interface

24 SDI input (BNC interface)

25 LED lamp

26 TDR cable test interface

27 DC12V2A power output , for provisional DC power supply

28 RS232 Interface: RS232 communication for the PTZ

29 RS485 Interface: RS485communication for the PTZ

30 Video image signal output（BNC interface）/cable scan interface

31 Video image signal input（BNC interface）

32 Optical power meter interface (Optional)

33 Visible red laser source emits Interface 34 UTP cable port: UTP cable tester port/ Cable scan port 35 Micro SD card moveable,default 4G, support Micro SD card up to 32G. 36 Audio input 37 HDMI output interface

page

38 Audio output 39 PoE power supply output/Lan test interface, 40 PSE power supply input interface 41 DC12V2A charging interface 42 DC12V2A power output , for provisional DC power supply

3. Operation

3.1

Installing the Battery

The tester has built-in lithium ion polymer rechargeable battery. The battery cable inside battery cabin should be disconnected for safety during transportation! Usually it doesn’t need to disconnect the cable at the normal use Pressing the key continuously can power on or off the tester.

Notice：Pls use the original adaptor and connected cable of the device!

When the battery icon is full or the charge indicator turns off automatically, indicate the battery

charging is completed

When the Charge Indicator turns off, the battery is approximately 90%

charged. The charging time can be extended for about 1 hour and the charging time within 12 hours will not damage the battery.

Notice ：Press the key several seconds to restore the default settings when the

instrument works abnormally.

Multi-meter: the red and black multi-meter pen must insert the corresponding port.

page

Warnings：Instrument communication port is not permitted access circuit voltage over 6V,

otherwise damage the tester.

Warnings：Not allow insert multi-meter pen in the current terminal to measure voltag

3.2

Instrument connection

3.2.1

IP camera connection

Power the IP camera by outter power source, then connect the IP camera to the IPC tester’s LAN port, if the link indicator of the tester’s LAN port is green and the data indicator flickers, it means the IP camera and the IPC tester are well connected. If the two indicators don’t work, it needs to check if the IP camera is powered on or the network cable is ok.

page

Note：if the IP camera does not support external power supply, but only supports PoE power, then connect the IP camera to IP tester’s LAN port ,The tester will supply PoE Power for IP camera. Before connecting, the PoE switch and tester must be disconnected. It means tester’s PSE port cannot be connected to any network cable when its LAN port is supplying the PoE power to the IP camera.

If use the tester’s menu to turn off the tester’s PoE power supply, the PoE switch and the power sourcing equipment are allowed to connect to the tester’s PSE port, and the PoE power will be supplied to the IP camera by the tester’s LAN port. On this condition, the tester cannot receive data from IP camera, but the computer connected to the PoE switch can receive the data via the the tester.

Warning：PoE switch or PSE power sourcing equipment only can be connected to tester “PSE

IN” port, or damage the instruments

3.2.2

Analog camera test

page

(1) The camera or dome video output is connected to CCTV Tester VIDEO IN,the image display on the tester . (2) CCTV Tester “VIDEO OUT” interface connect to the Video input of monitor and optical video transmitter and receiver, the image display on the tester and monitor (3) Connect the camera or the speed dome RS485 controller cable to the tester RS485 interface ,(Note positive and negative connection of the cable).Support RS232 PTZ controller ,connect the RS232cable to RS232 interface of the tester

3.3.3 SDI Camera Test

（1） The camera or dome video output is connected to CCTV Tester VIDEO IN,the image

display on the tester . tester just support SDI IN, not support SDI OUT function

page

（2） Connect the camera or the speed dome RS485 controller cable to the tester RS485

interface ,(Note positive and negative connection of the cable).Support RS232 PTZ controller ,connect the RS232cable to RS232 interface of the tester

3.3 OSD menu

 Press the key 2 seconds to turn on  Press the key 2 seconds to turn off  short press the key to enter sleep mode,press it again to test if tester work abnormally

and cannot be turned off , Press the key several seconds to turn off, the tester reset

Select Icons to enter, if quit, Please click

page

Click SD card, install or remove SD card

Press function Icons seconds, tip: whether move this icon to APPS file, if some function not be often used, can move these function icons to APPS.

Click icon “APPS” tool, to show all collected function icons, Click , back to the tester’s main menu

page

In APPS file, Select icon and press it for seconds, tip: whether move the file to the desktop?

3.3.1 Video monitor test (PTZ control)

Analog camera test and PTZ control, click icon to enter

page

Display the input video image, click the top menu bar icon to enter video level meter, (PEAK level, SYNC level, COLOR BURST measurement) Select relative function on the right side Toolbar to operate , functions including “Photos”, “Snapshot” , “Record” , “Playback” , “PTZ” , “Set” , Click to quit, or press back to menu. Click the screen twice quickly, can be full zoom in on the touch screen.

(1) PTZ controller parameter setting

Select and click icon “PTZ”,to enter PTZ setting：

page

A. Protocol Use the up and down arrow keys to move the yellow cursor to the “protocol ”, set corresponding

Protocol and support more than thirty PTZ protocols. Such as Pelco-D、Samsung、Yaan、LiLin、 CSR600、Panasonic、Sony-EVI etc.

B. Port

Click and move, to “port” Select the communication port for the PTZ camera controlling (RS232/485) C. Baud Move the yellow cursor to “Baud”, Select the baud rate according to baud rate of the PTZ camera.(150/300/600/1200/2400/4800/9600/19200/57600/115200)

D. Address

Set the ID according the ID of PTZ camera (0~254), the setting address data must be consistent the speed dome address.

E. Pan speed: Set the pan speed of PTZ camera (0~63) F. Tilt speed: Set the tilt speed of PTZ camera (0~63) G. Set preset position (Set PS) Click and select “Set PS”, set and save preset position number(1~128), H. Call the preset position (Go ps)

Click and select “Set PS”, set and save preset position number (1~128), click “sure” to save, Call some special preset number,can call the dome camera menu

Check and set the protocols, address, interface and baud, all must be consistent with the dome camera, dome camera, then the IPC tester can test .After setting the parameter, the tester can control the PTZ

and lens To control PTZ by screen touch: Tap left, right, upward and downward on the touch screen to control the PTZ rotation direction. By two fingers move outward and inward on the touch screen to zoom in and out the PTZ.

+ 66 hidden pages

OnvianTech IPC4300ADH User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual