Page 1
Vst/Pst Controller Ver. A1.00
P/N 1100035 page a
Page 2
Vst/Pst Controller Ver. A1.00
FCC Compliance
FCC Compliance
Labeling Requirements CFR 47, FCC part 15, Sections 15, 19, 109.
A device shall bear the following label in a conspicuous location on the device.
a) VST/PST Controller
OTI GMS FCC ID: JNX-13560M915MCON
Manufacturer: On Track Innovations Ltd.
This device complies with Part 15, of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received,
including interference that may cause undesired operation.
b) VST Tag
This device complies with Part 15, of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including
interference that may cause undesired operation.
NOTE: This equip ment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15, subpart C of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a resi dential installation. This equi pment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment of f and on, th e user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which this receiver is connected.
Consult the dealer or an experienced radio/TV technician for help
Changes or modifications in this equipment, not expressly approved by the
party responsible for compliance (On Track Innovations Ltd,) could void the
user’s authority to operate the equipment.
P/N 1100035 page a
Page 3
Vst/Pst Control ler Ver. A1 .00
Table of Contents
Table of Contents
FCC COMPLIANCE
TABLE OF CONTENTS........ ... ................. ... ................. ... .................. ... ................. ... ................. 1-1
1.
2. VST/PST SYSTEM ETU PRODUCT OVER V I EW..... ... ................. ... ................. ... ......... 2-1
3. INSTALLATION REQUIREMENTS ............................................................................... 3-3
SAFETY
1.1 USA................................................................................................................................ 1-2
2.1 P
2.2 G
2.3 A
3.1 PST A
3.2 S
3.3 VST A
3.4 VST/PST C
RODUCT DESCRIPTION
ENERAL DESCRIPTION:........................................................................................ 2-1
DDITIONAL DETAILS:........................................................................................... 2-1
2.3.1
2.3.2
2.3.3
UPERVISOR
3.3.1
3.3.2
3.3.3
3.4.1
3.4.2
3.4.3
REQUIREMENT ........................................................................................ 1-2
Power supply:............. ... .................. ... ................. ... .................. .. .................. . ......... 2-1
Communication:..................................................................................................... 2-2
Antennas:...............................................................................................................2-2
NTENNA WIRING
NTENNA WIRING
Installation Guide Lines......................................................................................... 3-5
Wiring Guidelines .................................................................................................. 3-5
Grounding .............................................................................................................. 3-5
ONTROLLER
Safety...................................................................................................................... 3-5
Installation Guidelines........................................................................................... 3-6
Wiring Guidelines .................................................................................................. 3-6
............................................................................................................A
.................................................................................................. 2-1
.................................................................................................. 3-4
NTENNA WIRING
A
....................................................................................... 3-4
.................................................................................................. 3-4
................................................................................................. 3-5
4. MECHANICAL INSTALLATION.................................................................................... 4-1
5. ELECTRICAL INSTALLATION...................................................................................... 5-1
P/N 1100035 page 1-1
Page 4
Vst/Pst Control ler Ver. A1 .00
Safety Requirement
1.
Safety
Requirement
1.1 USA
Installation of 120VAC supply to the VST/PST Controller must be done in accordance
with National Elect r ic Code (NEC) requirements.
The VST/PST controller uses 120VAC power supply connected terminals in a
partitioned area marked by a yellow triangle with lightning bolt
indicating presence of hazardous vo ltage.
Keep hand off this ar ea!
Warning!
Unit is supplied with 120VAC plug-in pow er cord.
Do not connect the main supply before installation is complete.
Disconnect power fr om the main suppl y before attempting to re place 1A fuse in AC
supply terminal.
Removal of VST/PST controller cover for inspection or maintenance is permitted for
qualified person nel only.
P/N 1100035 page 1-2
Page 5
Vst/Pst Control ler Ver. A1 .00
VST/PST System ETU Product Overview
2. VST/PST System ETU Product Overview
2.1 Product Description
The VST/PST Controller supports both long-range vehicle smart tags operating at
900 MHz and passive proximity transponders operating at 13.56MHz.
It’s main use is Smart Card/Tag Payment System.
It can serve as interface to a host computer or be used as a standalone unit.
At the heart of the VST/PST controlle r lies OTI’s MCI2 PCB.
The MCI2 is a microprocessor based smart transceiver suppo rt ing two 13.56MHz
transmission channels, so as to enable communication with PST tags carried by users.
The plug in VST Transceiver mounted on the M CI enables communication with VST in the
vehicle.
2.2 General description:
The VST/PST system c omprises three el e ment s:
• VST/PST Controller
• VST tag
• PST tag
The VST portion of the system suppor t co mmunication between the VST tag and the
controller over distances of up to few tens of meters, utilizing 915MHz communication
frequency.
The PST portion o f the system support comm unication of the PST tag and the
controller over distances of up to 10cm, ut ilizing 13.56MHz frequency.
The Controller sup port one VST communication channel and two PST communication
channels.
It also support RS232 communication to host channel and one signaling channel
comprising two indication signals.
The system is used to perform “transaction” of data between the VST or PST tags and
the controller fo r various applications.
2.3 Additional details:
2.3.1 Power supply:
Controller – 110/220VAC.
VSR tag – 3.6V battery at few tens of mA.
PST tag – no independe nt power source. It draws its power from the controller’s
antenna transmitted power. Current consumption is in the range of few mA.
P/N 1100035 page 2-1
Page 6
Vst/Pst Control ler Ver. A1 .00
VST/PST System ETU Product Overview
2.3.2 Communication:
VST tag:
• 915MHz.
• Normal bi-directional, transmit/receive, half-duplex.
• Digital data, Binary FSK.
PST tag:
• 13.56 MHz.
Special bi-directional, half duplex:
•
Controller to tag communication – AM.
o
Tag to controller communication – Load modulation.
o
Digital data, pulse width coding.
•
2.3.3 Antennas:
2.3.3.1 VST channel:
Controller:
• Detachable directiona l antenna.
VST tag:
• Integral “L” antenna.
2.3.3.2 PST channel:
Controller:
• Detachable loop antennas.
PST tag:
• Integral loop antenna.
P/N 1100035 page 2-2
Page 7
Vst/Pst Control ler Ver. A1 .00
Installation Requirements
3. Installation Requirements
• The intended applicat ion of the system is for the commercial and or industrial uses.
• The product can not be sold to the general public, but only to the system ’s Operating
Company. When the system is sold by the Operating Company to the customers, the
Product is installed only by the professional installers, qualified (“licensed”) by the
company for this purpose.
• The installation must be co ntrolled and follow the requirement of “Installation Manual”.
Each potential installer receives special tra ining, which is a condition for receiving the
license from the Operating Company to become a “licensed” installer. The installation
itself is a complex procedure, as described in the “Installation Manual”. It includes not
only the mechanical installation, but additional procedure of interconnection to the main
computer via modem, software initialization, registration of the specific Product in the
Operating Compa ny’s control center, performance of the initial test procedure. All these
are the tasks of the Product installer, wh ic h can only performed by specially trained
professional.
system requires installation of certain electrical equipment that must be performed by a licensed
electrician.
120VAC supply to the VST/PST Controller mu st be done in accordance with National
Electric Code (NEC ) requirements.
Installation and wiring of VST antenna must be performe d by a qualified technician.
The VST antenna requires separate grounding Use 10AWG wire to connect between
the antenna mounting bracket and ground.
.Note: Outdoor units and antennas should be installed ONLY by experienced
installation prof essionals who are famili ar with local building a nd safety codes
and, wherever applicable, are licensed by the appropriate government
regulatory author ities. Failure to do so my void the OTI product warranty and
my expose the end use r or the service provider to legal and finan cial liabilities.
OTI and its resellers or distributors are not liable for injury, damage or
violation of regulations associated with the installation of outdoor units or
antennas.
WARNING:
The installer should configure the output power level of antennas, according to
It is the responsibility of the installer to ensure that when using the outdoor
antenna kits in the United States (or where FCC rules apply), only those antennas
certified with the product are used. The use of any antenna other than those
certified with the product is expressly forbidden in accordance with FCC rules
CFR47 part 15.204."
country regulations and per antenna type.
P/N 1100035 page 3-3
Page 8
Vst/Pst Control ler Ver. A1 .00
Installation Requirements
3.1 PST Antenna Wiring.
The PST antenna in the window panel is wired to the VST/PST Controller via BNC
connector near the window panel. Wiri ng should be performed by qualified technetium
only.
The PST antenna in the window panel has a 23” coax cable terminated with a BNC
connector.
Connect this cable to a 22 foot long RG174 coax cable routed through protected
conduit and connected to the VST/PST Controller MCI terminal strip (refer to Figure 32: VST/PST Signal Wiring).
THE ANTENNA CABLES MUST NOT BE CUT! They must be used in the length
provided.
Note:
After connecting the PST antenna cable to the cable from the VST/PST controller, wrap
3M Scotch-Se al 22 29 Mastic Tape over the BNC connectors to seal them against
moisture
3.2
Supervisor
Antenna wiring
The Supervisor ant enna should be placed near the payment window terminal printer. It
is intended as interface between the Supervisor card and the system.
Secure antenna in pla ce with mounting screw s .
Make sure the antenna is not mounted over or placed near a metallic surface!
The antenna is supplied with a 23 feet 11 inch RG174 coax cable. The coax cable
should be routed through protected conduit and connected to the VST/PST Controller
MCI terminal strip (Refer to Figure 3-2: VST/PST Signal Wi rin g).
THE ANTENNA CABLE MUST NOT BE CUT! It must be used in the length
provided.
3.3 VST Antenna wiring
Use RG58 coax cable. The VST anten na is wired to the VST/PST controller. Both VST
antenna and VST/ PST Controller have SMA connectors. Wiring should be performed
by qualified technetium only.
P/N 1100035 page 3-4
Page 9
Vst/Pst Control ler Ver. A1 .00
Installation Requirements
3.3.1 Installation Guide Lines
The VST antenna should be mounted outside window counter. The antenna should be
mounted horizontal facing down approximately 10 feet above road level.
Connect mounting brackets to VST antenna mounting bolts.
Anchor Mounting brackets to wall or ceiling using 6mm KS-Anchors. Drill and mount
the anchors through the mounting bracket holes.
3.3.2 Wiring Guidelines
The VST antenna pan el is supplied with an SMA connector. RG58 coax cable should
be used. Cable length should not exceed 12 feet. The coax cables should be routed
through protected conduit and connect ed to the SMA connector on the VST/PST
controller box. Allow for a small downward loop in the cable before entering the wall
to prevent water seepage into the wall.
3.3.3 Grounding
The VST antenna requires separate grounding Use 10AWG wire to connect between
the antenna mounting bracket and ground.
3.4 VST/PST Controller
3.4.1 Safety
The VST/PST controller uses 120VAC power supply connected terminals in a
partitioned area marked by a yellow triangle with lightning bolt
indicating presence of hazardous voltage.
Keep hand off this are a!
Warning!
Unit is supplied with 120VAC plug-in pow er cord.
Do not connect the main supply before installation is complete.
Disconnect power fr om the main suppl y before attempting to re place 1A fuse in AC
supply terminal.
Removal of VST/PST controller cover for inspection or maintenance is permitted for
qualified person nel only.
P/N 1100035 page 3-5
Page 10
Vst/Pst Control ler Ver. A1 .00
D
Installation Requirements
3.4.2 Installation Guidelines
The VST/PST Controller is supplied in a metal enclosure. The dimensions of the box
are W = 200mm, H = 300 mm, D = 80mm. Weight: 4.2 Kg.
The VST/PST Controller should be mounted inside the the drive thru payment windo w
counter. The unit should be mounted at least 3 feet above floor level.
3.4.3 Wiring Guidelines
3.4.3.1 120VAC Power
Stud
GN
120 VAC
POWER IN
Power cable
1A
L
N
Figure 3-1: 120VAC Power Wiring
Do not apply power to the VST/PST controller until installation is complete!
P/N 1100035 page 3-6
Page 11
Vst/Pst Control ler Ver. A1 .00
Installation Requirements
3.4.3.2 VST/PST Signal Wiring
SMA
Connector
VST PCB
VST Antenna
GND
MCI PCB
ANT2 ANT1
SIG
Center
6
#2
Supervisor
Antenna
GND
Screen
Center
Connector
SIG
Relays
GND
R2R3
R1
4
VST PST
Screen
BNC
#1
PST
Antenna
GND
VST Button
Window Panel
4 4
IN8
3 3
(G) (R)
Thanks
Lights
Figure 3-2: VST/PST Signal Wiring
3
(BL)
(3A Fuse)
C
F2
57
TB2
RS232
TXD
GND
RXD
3
32 781
Omni Terminal Printer
654
RJ 45
RS232
P/N 1100035 page 3-7
Page 12
Vst/Pst Control ler Ver. A1 .00
Installation Requirements
VST Transceiver
Board
TR LEDs
TR2
TR1
SW1
SW2
Antenna
Terminals
VST Transceiver LEDs
LOCK
3.4.3.3
VST/PST Lay ou t
REC
REC
MCI LEDs
+7.5V +5V-TX
+5V
SAM
+VIN
+VL
8 Input LEDs
8 Output LEDs
RS232
Terminals
Input
Terminals
Output
Relays
230/120VAC Supply Input
Figure 3-3: VST PST - Interface Layout
230/120 to
12VAC
Transformer
P/N 1100035 page 3-8
Page 13
Vst/Pst Control ler Ver. A1 .00
Mechanical Installation
4. Mechanical Installation
160 mm
VST/PST Controoler
220mm
Box Dimensions:
W = 200mm, H = 300mm, D = 80mm
Cable Entries
340mm
8mm
Figure 4-1: VST PST - Enclosure Layout
The VST/PST Controller is intended for w all mounting. The unit should be fixed to the
wall with four mounting screws through t h e 4x 8mm moun t i n g hol es .
Unit can be mounted either indoors or outdoors. To prevent overheating the unit should
not on a wall fully exposed to sunlight.
P/N 1100035 page 4-1
Page 14
Vst/Pst Control ler Ver. A1 .00
Electrical Installation
5. Electrical Installation
VST Antenna
PST/VST Controller
VST Transceiver
MCI2
SMA
Connector
ANT1ANT2
SIG
SIG
GND
1
RG174 Coax cable
RG174 Coax cable
GND
IN8
2
IN
8
GND
GN
BK
5
R3
3
4
OUT3OUT
GND
In8
L2
L3
GND
GND
OR
BN
12V 120V 120V
Transformer
2x120VAC Input
12V3.3A Output
Y/GN
GND
L1
GND
BK
Y/GN
AC
AC
R
Metal Partition
RWBKBL
Stud
Y/GN
To cover
Y/GN
GND
P3
TB2
RS232 TB4 TB5
TXD
RXD
GND
GN
GN
BK
BK
1
1
5
5
R2
R1
3
3
2
2
4
4
OUT
1
2
Y/GN
3A
F
C
1A
H
120VAC H
(OPTIONAL)
C
C
RS232
POWER IN
Power cable
3x18AWG
PST/VST Controller wiring
PST
Antenna
PST
Antenna
Communication
5-1: Wiring Diagram
P/N 1100035 page 5-1
Loading...