On Track Innovations OTI SCIBA2 Users manual

SCIBA2
User & Installation Manual
Version 1.00
(O T I)
Z.H.R Industrial Zone P.O. Box 32 Rosh Pina 12000 Israel Tel: 972-4-6868000 Fax: 972-4-6938887
SCIBA2 User & Installation Manual Version 1.00 Revision History
Revision History
Version Description Date Author
1.00 Preliminary data 15/03/04 Avner
1.00 Minor corrections 18/03/04 Hemy
1.00 Minor corrections 21/03/04 Hemy
1.00 Minor corrections 11/04/04 Hemy
1.00 Minor corrections 13/04/04 Avner
page A
SCIBA2 User & Installation Manual Version 1.00 NOTICE
NOTICE
This manual contains intellectual property, including but not limited, to trade secrets and know-how, operation procedures and production procedures that belong solely to OTI. Disclosure and/or use and/or reproduction of any part of the above are strictly forbidden, except under a written license from OTI.
page B
SCIBA2 User & Installation Manual Version 1.00 FCC Compliance
FCC Compliance
OTI SCIBA2 FCC ID: JNX-OTI-SCIBA2 Manufacturer: On Track Innovations Ltd. This device complies with Part 15, of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received,
including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from
that to which this receiver is connected.
Consult the dealer or an experienced radio/TV technician for help
Warning! Changes or modifications in this equipment, not expressly approved by the party responsible for compliance (On Track Innovations Ltd,) could void the user’s authority to operate the equipment.
Warning! This product was tested with special accessories (shielded cables and/or special connectors or other), which must be used with the unit to insure compliance.
page C
SCIBA2 User & Installation Manual Version 1.00 FCC Declaration of Conformity
FCC Declaration of Conformity
We, the undersigned,
OTI America
Address: Suite 201, 1601 S. De Anza Blvd., Cupertino, CA 95014
Telephone number: 408-252-0333
Fax number: 408-252-8414
are the Responsible Party for this Declaration, certify and declare under our sole
responsibility that the following equipment:
Brand Type Product description
OTI SCIBA2 Contactless card reader
complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may
cause undesired operation.
page D
SCIBA2 User & Installation Manual Version 1.00 Table of Contents
Table of Contents
REVISION HISTORY...................................................................................................................................A
NOTICE ..........................................................................................................................................................B
FCC COMPLIANCE .....................................................................................................................................C
FCC DECLARATION OF CONFORMITY ...............................................................................................D
TABLE OF CONTENTS ............................................................................................................................... E
1 INTRODUCTION .............................................................................................................................. 1-1
2 TECHNICAL SPECIFICATIONS ................................................................................................... 2-3
3 SYSTEM CONFIGURATION .......................................................................................................... 3-4
3.1 CIBA2
READER............................................................................................................................ 3-5
3.1.1 Standard Connectors............................................................................................................... 3-5
3.1.2 Optional Connectors................................................................................................................ 3-6
3.1.3 LEDs........................................................................................................................................ 3-7
3.1.4 Jumpers.................................................................................................................................... 3-7
3.1.5 SAMs........................................................................................................................................ 3-7
3.2 A
3.3 P
NTENNA ..................................................................................................................................... 3-9
OWER SUPPLY............................................................................................................................. 3-9
4 INSTALLATION INSTRUCTIONS .............................................................................................. 4-10
4.1 R
4.2 A
EADER INSTALLATION.............................................................................................................. 4-10
NTENNA INSTALLATION ........................................................................................................... 4-10
5 FLASH MEMORY PROGRAMMING.......................................................................................... 5-11
5.1 I
5.2 PC
5.3 P
5.4 H
5.5 P
NTRODUCTION ........................................................................................................................... 5-11
REQUIREMENTS ..................................................................................................................... 5-11
ROGRAMMER SOFTWARE INSTALLATION .................................................................................. 5-11
ARDWARE SETUP ..................................................................................................................... 5-11
ROGRAMMING ........................................................................................................................... 5-12
5.5.1 Flash Memory Files............................................................................................................... 5-12
5.5.2 Programming Procedure....................................................................................................... 5-12
5.6 H
ELP........................................................................................................................................... 5-12
FCC DECLARATION OF CONFORMITY ...............................ERROR! BOOKMARK NOT DEFINED.
page E
Loading...
+ 12 hidden pages