On Track Innovations OTI SAT6700 User Manual

Confidential & Proprietary

Version 1.9

UNO

Specifications

Version 1.9

Notice

This manual contains intellectual property including,
but not limited to, trade secrets and know-how,
operation procedures and production procedures that
belong solely to oti.

Disclosure, use, and/or production of any part of
the above are strictly forbidden, except under a

written license from oti.

Uno Specifications Version 1.9

FCC Compliance

FCC Compliance

This device (Saturn 6700) complies with Part 15, of the FCC Rules.
Operation is subject to the following two conditions:

1. This device may not cause harmful interference,

and

2. This device must accept any interference received, including interference that

may cause undesired operation

NOTE:

This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15, subpart C of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:

 Reorient or relocate the receiving antenna.
 Increase the separation between the equipment and receiver.
 Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

 Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications in this equipment, not expressly approved by the
party responsible for compliance (On Track Innovations Ltd,) could void the
user’s authority to operate the equipment.

FCC ID: JNX-OTI-SAT6700

Responsible Party:

On Track Innovations LTD..

Z.H.R Industrial Zone.
Rosh Pina 12000
ISRAEL
Phone: [phone]
Email: [e-mail]

Confidential & Proprietary Page 1

Uno Specifications Version 1.9

Table of Contents

Table of Contents

FCC COMPLIANCE ...................................................................................................................................... 1

TABLE OF CONTENTS ................................................................................................................................ 2

TABLE OF FIGURES .................................................................................................................................... 3

VERSIONS TABLE ........................................................................................................................................ 4

1 INTRODUCTION .................................................................................................................................. 5

1.1 CERTIFIED AND SUPPORTED APPLICATIONS...................................................................................... 6

1.2 SUPPORTED STANDARDS .................................................................................................................. 7

2 BASIC CONTACTLESS OPERATION .............................................................................................. 8

3 TECHNICAL SPECIFICATIONS ....................................................................................................... 9

3.1 PRODUCT FEATURES ......................................................................................................................... 9

3.2 PRODUCT TECHNICAL SPECIFICATIONS .......................................................................................... 10

4 READER MODELS ............................................................................................................................. 12

4.1 RS232 MODEL ................................................................................................................................ 12

4.2 USB MODEL ................................................................................................................................... 12

4.3 INTERFACE CABLES ......................................................................................................................... 13

4.3.1 RS232 cable ............................................................................................................................... 13

4.3.2 USB Cable ................................................................................................................................. 14

5 DIMENSIONS ...................................................................................................................................... 15

5.1 FRONT VIEW ................................................................................................................................... 15

5.2 SIDE VIEW ...................................................................................................................................... 16

6 UNO MOUNTING................................................................................................................................ 17

6.1 ON PANEL MOUNTING .................................................................................................................... 18

6.2 FLUSH MOUNTING .......................................................................................................................... 20

6.3 COUNTERTOP (DESKTOP) MOUNTING ............................................................................................. 25

7 CONTACT US ...................................................................................................................................... 26

Confidential & Proprietary Page 2

Uno Specifications Version 1.9

Table of Figures

Table of Figures

Figure 2-1: Card Presentation ............................................................................................................ 8

Figure 5-1: Front View ..................................................................................................................... 15

Figure 5-2: Side View ...................................................................................................................... 16

Figure 5-3: UNO Size Scale ....................................................................................................... 16

Figure 6-1: Flush and On Panel Mounting ............................................................................ 17

Figure 6-2: UNO Mounting Studs .................................................................................................... 18

Figure 6-3: UNO Panel Mounting view ................................................................................... 19

Figure 6-4: UNO Panel Mounting Drilling Template ...................................................................... 19

Figure 6-5: UNO Flush Mounting – Front View .................................................................... 20

Figure 6-6: UNO Flush Mounting – Side View ............................................................................... 21

Figure 6-7: UNO Flush Mounting – Front View .................................................................... 21

Figure 6-8: UNO Flush Mounting – Side View ...................................................................... 22

Figure 6-9: UNO Flush Mounting – Angular View ............................................................... 23

Figure 6-10: UNO Flush Mounting – Rear View ................................................................... 24

Figure 6-11: Uno Flash Mounting - Cutout...................................................................................... 24

Figure 6-12: UNO Countertop (Desktop) Mounting – Front View ................................... 25

Confidential & Proprietary Page 3

Uno Specifications Version 1.9

Version

Description

Date

Name

1.1

First version

2014-11-02

Moshe
Cohen

1.2

 Supporting operation voltage

of 8 - 45VDC instead of 2 ­15 VDC

 Adding a note regarding

"Behind Panel" mounting

 Having only one

thickness configuration
(17mm thickness) instead
of 17 or 25 mm

2014-11-10

Moshe
Cohen

1.3

 Reader structural update
 New connectors
 Updates about the mounting

options

2014-11-30

Moshe
Cohen

1.4

 New pinout for the full

interface connector

 New pictures of the UNO

prototype

 Update contact information

of the oti America support
team

2015-01-13

Moshe
Cohen

1.5

 New warning regarding

power supply stability

 New warning regarding

mounting on metal

 Replacing "flat" wording by

"flush"

2015-07-14

Aharon
Binur

1.51

Decrease the input voltage range to
40Vdc

2015-09-29

Aharon
Binur

1.6

Add Recommended Cutout and
Drilling for installation

2015-12-03

Aharon
Binur

1.7

Adding notes to FCC compliance
statement.

2016-04-14

Avner

1.8

Update total power sonsumption and
IP rating

2016-05-10

Hemy

1.9

Add clear distinction between USB
and RS232 models.

2016-05-16

Hemy

Versions Table

Versions Table

Confidential & Proprietary Page 4

Uno Specifications Version 1.9

Introduction

1 Introduction

The UNO is an ultra-compact, certified payment NFC Reader based on oti’s field proven
technology which is specifically designed for payment and mass transit applications. Its compact
design enables easy integration and installation in unattended self-service payment stations, such
as ATMs, AVMs, TVMs, gaming and gambling machines, kiosks, access control gates and more.

The UNO uses oti’s patented matched antenna technology.
The UNO supports SAM house that allows the reader to access its own or external security

elements such as Mifare Authentication SAM.
The UNO is designed to be seated on any counter as an attended reader or alternatively can be

installed as part of an unattended vending or service machine.
UNO’s plug-and-play design makes it easy to connect to any existing infrastructure and POS

terminal, quickly upgrading it to contactless operations without disrupting ongoing business
operations. In its USB configuration, the UNO is USB powered, this option contributes to the easy
installation and maintenance of the reader.

Confidential & Proprietary Page 5

Uno Specifications Version 1.9

Introduction

1.1 Certified and Supported Applications

The UNO is certified and supports the following contactless
applications:

 EMV

o Contactless EMV L1

 VISA

o VISA PayWave MSD
o VISA PayWave qVSDC
o NDOT over VISA for transportation
o VISA Global Transit Payment Pilot Specification
o VISA Pilot Visa PayWave Ticketing Extension Specification
o VISA Asia Pacific WAVE 2

 MasterCard

o MasterCard PayPass M/Chip (including Data Exchange)
o MasterCard PayPass Mag Stripe
o NDOT over MasterCard for transportation

 American Express

o AMEX ExpressPay

 Discover

o Discover ZipNetwork

 Interac

o Interac Flash

 SoftCard

o SoftCard (ISIS) SmartTap

 Mifare

o Mifare Ultralight
o Mifare Classic
o Mifare DESFire (optional)

 Transparent (Pass-Through) Communication

o ISO/IEC 14443 Type A - Transparent Proximity
o ISO/IEC 14443 Type B - Transparent Proximity
o ISO/IEC 15693 Vicinity (optional) - Transparent Vicinity

 Other

o Additional proprietary applications

*In process of certification

Confidential & Proprietary Page 6

Uno Specifications Version 1.9

Introduction

1.2 Supported Standards

The UNO is compatible with the following standards:

 FCC
 CE
 UL
 RoHS compliance
 ISO 9001: 2008
 ISO/IEC 14443 Proximity Type A&B
 ISO/IEC 15693 Vicinity
 Mifare
 MasterCard TQM label
 IPX5

Confidential & Proprietary Page 7

Uno Specifications Version 1.9

Basic Contactless Operation

2 Basic Contactless Operation

When a valid contactless payment card is presented to the reader, the reader performs a
payment transaction with the contactless card. If the transaction is accepted, the unit
will display a row of 4 LEDs that light up in sequence and the reader buzzer will
inform the user about the transaction verdict. The reader then communicates the
transaction data to the Host (POS).

A landing zone logo, lighted by the reader, on the graphic overlay indicates where the
contactless card or tag should be presented.
The interactive LEDs and Buzzer give the user an indication of the transaction status.

Figure 2-1: Card Presentation

Confidential & Proprietary Page 8