On Track Innovations VSTTAG915M, 13560K915MCON Users manual
Vst/Pst Controller Ver. A1.00
P/N 1100035 page a
Vst/Pst Controller Ver. A1.00
FCC Compliance
FCC Compliance
Labeling Requirements CFR 47, FCC part 15, Sections 15, 19, 109.
A device shall bear the following label in a conspicuous location on the device.
a) VST/PST Controller
OTI GMS FCC ID: JNX-13560M915MCON
Manufacturer: On Track Innovations Ltd.
This device complies with Part 15, of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received,
including interference that may cause undesired operation.
b) VST Tag
This device complies with Part 15, of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including
interference that may cause undesired operation.
NOTE: This equip ment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15, subpart C of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a resi dential installation. This equi pment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment of f and on, th e user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which this receiver is connected.
Consult the dealer or an experienced radio/TV technician for help
Changes or modifications in this equipment, not expressly approved by the
party responsible for compliance (On Track Innovations Ltd,) could void the
user’s authority to operate the equipment.
P/N 1100035 page a
Vst/Pst Control ler Ver. A1 .00
Table of Contents
Table of Contents
FCC COMPLIANCE
TABLE OF CONTENTS........ ... ................. ... ................. ... .................. ... ................. ... ................. 1-1
1.
2. VST/PST SYSTEM ETU PRODUCT OVER V I EW..... ... ................. ... ................. ... ......... 2-1
3. INSTALLATION REQUIREMENTS ............................................................................... 3-3
SAFETY
1.1 USA................................................................................................................................ 1-2
2.1 P
2.2 G
2.3 A
3.1 PST A
3.2 S
3.3 VST A
3.4 VST/PST C
RODUCT DESCRIPTION
ENERAL DESCRIPTION:........................................................................................ 2-1
DDITIONAL DETAILS:........................................................................................... 2-1
2.3.1
2.3.2
2.3.3
UPERVISOR
3.3.1
3.3.2
3.3.3
3.4.1
3.4.2
3.4.3
REQUIREMENT ........................................................................................ 1-2
Power supply:............. ... .................. ... ................. ... .................. .. .................. . ......... 2-1
Communication:..................................................................................................... 2-2
Antennas:...............................................................................................................2-2
NTENNA WIRING
NTENNA WIRING
Installation Guide Lines......................................................................................... 3-5
Wiring Guidelines .................................................................................................. 3-5
Grounding .............................................................................................................. 3-5
ONTROLLER
Safety...................................................................................................................... 3-5
Installation Guidelines........................................................................................... 3-6
Wiring Guidelines .................................................................................................. 3-6
............................................................................................................A
.................................................................................................. 2-1
.................................................................................................. 3-4
NTENNA WIRING
A
....................................................................................... 3-4
.................................................................................................. 3-4
................................................................................................. 3-5
4. MECHANICAL INSTALLATION.................................................................................... 4-1
5. ELECTRICAL INSTALLATION...................................................................................... 5-1
P/N 1100035 page 1-1
Vst/Pst Control ler Ver. A1 .00
Safety Requirement
1.
Safety
Requirement
1.1 USA
Installation of 120VAC supply to the VST/PST Controller must be done in accordance
with National Elect r ic Code (NEC) requirements.
The VST/PST controller uses 120VAC power supply connected terminals in a
partitioned area marked by a yellow triangle with lightning bolt
indicating presence of hazardous vo ltage.
Keep hand off this ar ea!
Warning!
Unit is supplied with 120VAC plug-in pow er cord.
Do not connect the main supply before installation is complete.
Disconnect power fr om the main suppl y before attempting to re place 1A fuse in AC
supply terminal.
Removal of VST/PST controller cover for inspection or maintenance is permitted for
qualified person nel only.
P/N 1100035 page 1-2
Vst/Pst Control ler Ver. A1 .00
VST/PST System ETU Product Overview
2. VST/PST System ETU Product Overview
2.1 Product Description
The VST/PST Controller supports both long-range vehicle smart tags operating at
900 MHz and passive proximity transponders operating at 13.56MHz.
It’s main use is Smart Card/Tag Payment System.
It can serve as interface to a host computer or be used as a standalone unit.
At the heart of the VST/PST controlle r lies OTI’s MCI2 PCB.
The MCI2 is a microprocessor based smart transceiver suppo rt ing two 13.56MHz
transmission channels, so as to enable communication with PST tags carried by users.
The plug in VST Transceiver mounted on the M CI enables communication with VST in the
vehicle.
2.2 General description:
The VST/PST system c omprises three el e ment s:
• VST/PST Controller
• VST tag
• PST tag
The VST portion of the system suppor t co mmunication between the VST tag and the
controller over distances of up to few tens of meters, utilizing 915MHz communication
frequency.
The PST portion o f the system support comm unication of the PST tag and the
controller over distances of up to 10cm, ut ilizing 13.56MHz frequency.
The Controller sup port one VST communication channel and two PST communication
channels.
It also support RS232 communication to host channel and one signaling channel
comprising two indication signals.
The system is used to perform “transaction” of data between the VST or PST tags and
the controller fo r various applications.
2.3 Additional details:
2.3.1 Power supply:
Controller – 110/220VAC.
VSR tag – 3.6V battery at few tens of mA.
PST tag – no independe nt power source. It draws its power from the controller’s
antenna transmitted power. Current consumption is in the range of few mA.
P/N 1100035 page 2-1
Loading...