OPERATOR’S MANUAL
FOR
DRINK BLENDER
WARNING
USE PRE-MIXED GAS ONLY
MIXING RATIO
GASOLINE : PRE-MIXED OIL
FIRST 50 HRS 25 : 1
AFTER 50HRS 50 : 1
1.866.438.6836
MADE IN CHINA
Table of Contents
1. Parts List and General Specifications
2. Warnings
3. Before Using Your Drink Blender
4. Operating Instructions
5. General Maintenance
6. Trouble Shooting
7. Motor Specifications
1 6
Warning! Read and follow all safety precautions in the
operator’s manual. Failure to follow these instructions
could result in serious injury.
1. Parts List and Specifications
A. Parts List
(1) Stainless steel drink pitcher with lid
(2) Handlebar / Twist grip (twist grip attached to main frame via
throttle cable)
(1) Main frame with engine
(2) Handlebar screws (may be attached to handle bar)
(1) Gas/2-stroke oil mixing bottle
(1) Spark plug wrench
B. General Technical Statistics:
Length (in): 13
Width (in): 24.4 with handlebars
13 without handlebars
Height (in): 24.8
Maximum pitcher capacity: 2.5 qt
C. Engine Picture
2. Warnings
A. Once the handlebars are safely assembled and attached, it is OK to
lift and transport the “Drink Blender” using the handlebars.
B. Insert the handlebars, line up the screw
B
holes and insert the screws supplied
and fasten them down firmly.
Periodically check screws to maintain
Screw
a tight fit. Screws may loosen due to
vibration (see image B).
C
Kill button
C. Your “Drink Blender” has a safety kill button in
case of an emergency (see image C).
D. Your “Drink Blender” uses 2-stroke oil and
unleaded gas ONLY. Mixing Ratio: 25:1
(for 1
st
50 uses) and then switch to 50:1
E. Only operate your “Drink Blender” in well ventilated areas. Exhaust
from the engine contains harmful ingredients and any long term
exposure should be avoided.
F. Your “Drink Blender” is designed for use by ADULTS ONLY. DO NOT
operate when tired, ill or under the influence of alcohol, drugs or
medication.
G. Never leave your “Drink Blender” running or unattended.
H. Whenever using the “Drink Blender”, please be sure the unit is
located on secure, flat, and even surface before operating.
I. Please DO NOT touch the engine until the motor has stopped for at
least 10 - 15 minutes, as some parts of engine remain hot. This is to
protect from burns and heat damage.
J. Keep your “Drink Blender” away from heat or direct flames.
K. DO NOT fill your pitcher more than 3/4 full and securely hold the
pitcher and lid while operating.
3. Before Using Your Drink Blender
A. Always inspect and clean your “Drink Blender” pitcher and blades
before use.
B. Always inspect the nuts and bolts of your “Drink Blender” to ensure a
3 4
tight and secure fit.
C. WARNING: ALWAYS USE PRE-MIXED GAS ONLY!
D. Mix 50 part gasoline to 1 part 2-cycle oil in a gas container SHAKE
WELL and pour into fuel tank.
E. Your “Drink Blender” uses a standard 2-stroke motor so always use
unleaded gasoline.
F. Never fill your “Drink Blender” with fuel while motor is running, and
never overfill it!! Use caution when handling fuel. Move “Drink
Blender” away from fuel source before starting the engine.
G. Keep children, bystanders and pets out of the operating area.
H. Keep all parts of your body away from all moving parts when engine
is running.
4. Operating Instructions
A. Close the choke.
B. On the bottom of the carburetor, there is primer ball, press it until its
firm, then your “Drink Blender” should be ready to start!
C. Pull the pull-handle two or three times until your “Drink Blender” starts.
D. Close the choke valve, and it should be ready for action.
For a safety precaution, there is a red kill-button next to the twist grip.
5. General Maintenance
A. Check fuel level and all bolts & nuts, tighten if necessary. Check fuel
lines for any leakage and ALWAYS USE PRE-MIXED 50:1 FUEL.
B. Let your “Drink Blender” warm-up 3-5 minutes before use. Keep
handles dry, clean, and free of oil or fuel mixture.
C. Breaking-in the engine is important. DO NOT run full throttle within the
first 20 hours of use.
D. Please use fuel in accordance with the 50:1 ratio as described earlier.
E. If Engine malfunctions, DO NOT OPERATE, Contact 866.438.6836.
Service should be performed by qualified personnel.
6. Trouble Shooting
For hard start-up failure:
A. Check if fuel line is good.
B. Make sure the safety stop bottom is working smoothly.
C. Check to see if there is some air in the fuel line. If so, please press
or pump the primer ball until the fuel line is clean of any air bubble.
D. Check to see if the choke is open.
E. Check to see if the air and fuel is normal.
F. Make sure air filter is not clogged.
G. Please check to make sure air vent, muffler or fuel line are not
clogged and are functioning properly.
7. Motor Specifications
Item
Engine
Bore x Stroke
Spark plug
Carburetor
Speed idling
Turn way of engine output
Spark plug gap
Fire mode
Start mode
Fuel
Output
Scheduled power
Clutch type
Fuel consumption
Fuel tank volume
Parameter
Single cylinder, air-cooling 2 stroke
40mm x 34mm
BM6A
Double film
2700± 200rpm
Counterclockwise
0.6 - 0.7mm
PBI
Manual start-up
Unleaded gasoline: 2-stroke engine oil = 50:1
43cc
1.2kW @ 6500rpm
Centrifugal
610g / kW. h
0.72 qt
5 2
S
T
D
A
E
T
T
I
E
N
S
U
•
E
•
N
V
I
R
O
N
M
E
N
T
A
Y
C
N
E
G
A
N
O
I
T
C
L
E
T
P
R
O
“Drink Blender” engine meets Federal EPA standards for gasoline
engines pursuant to regulation 40 CFR 90.114.
Loading...