Page 1
Veris Differential Pressure Transducer Connection Instructions
For use with HOBO® H22, U12, U30, UX120-006M, and RX3000 data loggers and HOBO ZW data nodes
Applies to these Veris Differential Pressure Transducers:
Onset Part No. Air Pressure Range Output Veris Part No.
T-VER-PXU-L 0-10” WC 4-20mA (or 0-5V/0-10V) representing 0 to 10” WC PXULX05S (LCD display)
T-VER-PXU-X 0-10” WC 4-20mA (or 0-5V/0-10V) representing 0 to 10” WC PXUXX05S (no display)
This document provides instructions on connecting the Veris Differential Pressure
Transducers listed above to each of the following:
™
• FlexSmart
• Analog Sensor Port/Module used with HOBO U30 and RX3000 series data
loggers
• Voltage adapter used with the U12 and UX120-006M data loggers and ZW series
data nodes
It also lists configuration values used by HOBOware
each transducer. Note: For information on connecting the differential pressure transducer
to the pressure source, and other transducer details, refer to the documentation provided
by Veris.
Required
• Selected Veris Differential Pressure Transducer
• HOBO H22, U12, U30, UX120-006M, or RX3000 data logger, or HOBO ZW data node
• FlexSmart Analog Module, Onset Part No: S-FS-CVIA (for H22 series); Analog Sensor Port/Module option (for U30 and
RX3000 series); voltage adapter, Onset Part No. CABLE-ADAP5 or CABLE-ADAP10 (for U12, UX120-006M, or ZW
series)
• HOBOware software, version 2.2.1 or higher (2.4.0 or higher for U30 series; 3.6 or higher for UX120-006M);
HOBOware Pro 3.0 or higher for ZW series
• HOBOlink (for RX3000 series data loggers)
• Customer-supplied length of 18 AWG, shielded, multi-conductor cable
Analog Module used with HOBO H22 series data loggers
®
software to configure the logger for
Veris Differential Pressure Transducer
(Onset Part No. T-VER-PXU-L shown)
Connecting the Differential Pressure Transducer to the Analog Module or Port
H22 Connection
HOBO H22 Series D ata Logger
S-FS-CVIA
FlexSmart Analog Mo dule
FlexSmart Analog Mo dule
S2+
S1-
S1+
Shld
© 2009–2015 Onset Computer Corporation. All rights reserved. Onset, HOBO, HOBOware, and HOBOlink are registered trademarks and FlexSmart is a trademark of
Onset Computer Corporation. Other products and brand names may be trademarks or registered trademarks of their respective owners.
13038-D MAN-VERIS-PXL
S2-
Exc+
Exc-
Conductor
Conductor
for 4-20mA Output
Terminal Block
inside transducer housing
POWER/4-20mA
N/C
N/C
N/C
OUT (0-10V)
COM
ZERO
FlexSmart Analog Module
Shld
Differential Pressure Transducer
Customer-supplied 18 AWG
shielded multi-conductor cable
S2+
S1-
S1+
for 0-5V/0-10V Output
S2-
Exc+
Exc-
Conductor
Conductor
Conductor
Terminal Block
inside transducer housing
POWER/4-20mA
OUT (0-10V)
COM
N/C
N/C
ZERO
Page 2
Veris Differential Pressure Transducer Connection Instructions
U30 or RX3000 Connection (U30 Shown)
HOBO U30 Series Data Logger
Analog Sensor Port
Ch2 Signal
Shield
Conductor
Conductor
Ext Return
Ch2 Return
Terminal Block
inside transducer housing
POWER/4-20mA
N/C
N/C
N/C
OUT (0-10V)
COM
ZERO
Ch1 Return
Ch1 Signal
Shield
Exc Out
for 4-20mA Output
ZW, U12, and UX120-006M Connection
HOBO ZW Series Wireless Data Node; U12 or UX120-006M Logger
HOBO ZW Series Wireless Data Node or U12 Series Data Logger
(ZW shown)
Analog Sensor Port
Differential Pressure Transducer
Customer-supplied 18 AWG
shielded multi-conductor cable
Analog Sensor Port
Ch1 Return
Ch1 Signal
Shield
for 0-5V/0-10V Output
Ext Return
Ch2 Return
Ch2 Signal
Shield
Exc Out
Conductor
Conductor
Conductor
Differential Pressure Transducer
Terminal Block
inside transducer housing
POWER/4-20mA
OUT (0-10V)
COM
N/C
N/C
ZERO
*CAUTION: Polarity is very
important! Before plugging
AC-SENS-1 into AC power,
make sure the correct
polarity lead connections to
device are made as shown!
AC-SENS-1*
Blue (-)
Yellow (+)
CABLE-4-20MA
Connect to analog port
CABLE-4-20MA (for 4-20mA output) or
CABLE-ADAP5 (for 0-5VDC output) or
CABLE-ADAP10 (for 0-10VDC output)
inside transducer housing
(+)
(-)
N/C
N/C
N/C
Use appropriate termination for
connection (denoted with )
for 4-20mA Output
Terminal Block
POWER/4-20mA
OUT (0-10V)
COM
ZERO
Page 2 of 3
AC-SENS-1*
(+)
(-)
White (+)
Black (-)
(Red wire not used)
CABLE-ADAP5 or CABLE-ADAP10
for 0-5V/0-10V Output
AC-SENS-1*
Terminal Block
inside transducer housing
POWER/4-20mA
OUT (0-10V)
COM
N/C
ZERO
N/C
Page 3
Veris Differential Pressure Transducer Connection Instructions
Configuring the Data Logger for the Differential Pressure Transducer using HOBOware Software
HOBOware software provides configuration files for the transducers. The table below lists the recommended configuration values
that these files contain. For information on loading configuration files, refer to the software documentation.
Onset Part Nos. Channel
T-VER-PXU-L and
T-VER-PXU-X
Name
Diff Pressure 20 sec Current 4 20 mA 0 0.1 (or 0.25,
Warm-Up Measurement
Type
Voltage 0 5 (or 10) V
Raw
Value 1
Raw
Value 2
Raw
Units
Scaled
Value 1
Scaled
Value 2
0.5, 1, 2.5,
5, or 10)
Notes:
• Excitation power provided by the FlexSmart Analog Module (Onset Part No. S-FS-CVIA) with H22; by the Analog
Sensor Port/Module with U30 and RX3000; and by power adapter (Onset Part No. AC-SENS-1) with ZW, U12, or
UX120-006M.
• Both differential pressure transducer models have switch-selectable ranges and scales, as listed.
Scaled
Units
in WC
Page 3 of 3
Loading...