ON Semiconductor NC7WV17 User Manual

TinyLogic ULP-A Dual
Buffer with Schmitt-Trigger
Input

NC7WV17

The NC7WV17 is a dual buffer with Schmitt−trigger input in tiny

footprint

packages. The device is designed to operate for V

CC

=

0.9 V

to 3.6 V.

Features

• Designed for 0.9 V to 3.6 V V

• 2.2 ns t

at 3.3 V (Typ)

PD

Operation

CC

• Inputs/Outputs Over−Voltage Tolerant up to 3.6 V

• I

Supports Partial Power Down Protection

OFF

• Source/Sink 24 mA at 3.3 V

• Available in SC−88A and MicroPak™ Packages

• These Devices are Pb−Free, Halogen Free/BFR Free and are RoHS

Compliant

A1 Y1

1

GND

2

A2 Y2

3

SC−88A

6

5

4

Figure 1. Pinout Diagrams (Top Views)

V

CC

GND 2

1

MicroPak

Y1A1

6Y1A1 1

5V

4Y2A2 3

CC

www.onsemi.com

MARKING

DIAGRAMS

SIP6 1.45X1.0

MicroPak

CASE 127EB

Pin 1

CC = Specific Device Code
KK = 2−Digit Lot Run Traceability Code
XY = 2−Digit Date Code
Z = Assembly Plant Code

SC−88

DF SUFFIX

CASE 419B−02

1

XXX = Specific Devic Code
M = Date Code
G = Pb−Free Package

(Note: Microdot may be in either location)

*Date Code orientation and/or position may vary

depending upon manufacturing location.

CCKK

XYZ

6

XXXMG

G

1

A2 Y2

Figure 2. Logic Symbol

PIN ASSIGNMENT

Pin Function

1 A1

2 GND

3 A2

4 Y2

5 V

6 Y1

© Semiconductor Components Industries, LLC, 2004

February, 2021 − Rev. 2

1

See detailed ordering, marking and shipping information on
page 7 of this data sheet.

ORDERING INFORMATION

FUNCTION TABLE

Input Output

L L

H H

CC

1 Publication Order Number:

NC7WV17/D

NC7WV17

MAXIMUM RATINGS

Symbol Characteristics Value Unit

V

CC

V

IN

V

OUT

I

IK

I

OK

I

OUT

ICC or I

T

STG

T

L

T

J

q

JA

P

D

MSL Moisture Sensitivity Level 1 −

F

R

V

ESD

I

Latchup

Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be affected.

1. Applicable to devices with outputs that may be tri−stated.

2. Measured with minimum pad spacing on an FR4 board, using 10 mm−by−1 inch, 2 ounce copper trace no air flow per JESD51−7.

3. HBM tested to EIA / JESD22−A114−A. CDM tested to JESD22−C101−A. JEDEC recommends that ESD qualification to EIA/JESD22−A115A
(Machine Model) be discontinued.

4. Tested to EIA/JESD78 Class II.

DC Supply Voltage −0.5 to +4.3 V

DC Input Voltage −0.5 to +4.3 V

DC Output Voltage Active−Mode (High or Low State)

Tri−State Mode (Note 1)

Power−Down Mode (V

CC

= 0 V)

−0.5 to VCC + 0.5

−0.5 to +4.3

−0.5 to +4.3

DC Input Diode Current VIN < GND −50 mA

DC Output Diode Current V

< GND −50 mA

OUT

DC Output Source/Sink Current ±50 mA

DC Supply Current per Supply Pin or Ground Pin ±50 mA

GND

Storage Temperature Range −65 to +150 °C

Lead Temperature, 1 mm from Case for 10 Seconds 260 °C

Junction Temperature Under Bias +150 °C

Thermal Resistance (Note 2) SC−88A

MicroPak

Power Dissipation in Still Air SC−88A

MicroPak

377
154

332
812

Flammability Rating Oxygen Index: 28 to 34 UL 94 V−0 @ 0.125 in −

ESD Withstand Voltage (Note 3) Human Body Mode

Charged Device Mode

2000
1000

Latchup Performance (Note 4) ±100 mA

V

°C/W

mW

mW

www.onsemi.com

2

NC7WV17

RECOMMENDED OPERATING CONDITIONS

Symbol Parameter Min Max Unit

V

CC

V

V

OUT

T

t

r

Functional operation above the stresses listed in the Recommended Operating Ranges is not implied. Extended exposure to stresses beyond
the Recommended Operating Ranges limits may affect device reliability.

DC ELECTRICAL CHARACTERISTICS

Symbol

V

P

V

N

V

H

Positive DC Supply Voltage 0.9 3.6 V

DC Input Voltage 0 3.6

IN

DC Output Voltage Active−Mode (High or Low State)

Tri−State Mode (Note 1)

Power−Down Mode (V

Operating Temperature Range −40 +85 °C

A

, t

Input Transition Rise and Fall Time 0 No Limit ns/V

f

CC

= 0 V)

0
0
0

TA = 255C TA = −405C to +855C

Parameter Condition V

Positive
Threshold Voltage

(V)

CC

0.9 − 0.62 − − −

1.1 − − 1.0 − 1.0

Min Typ Max Min Max

1.4 − − 1.25 − 1.25

1.65 − − 1.5 − 1.5

2.3 − − 1.8 − 1.8

2.7 − − 2.2 − 2.2

Negative
Threshold Voltage

0.9 − 0.34 − − −

1.1 0.15 − − 0.15 −

1.4 0.2 − − 0.2 −

1.65 0.25 − − 0.25 −

2.3 0.4 − − 0.4 −

2.7 0.6 − − 0.6 −

Hysteresis
Voltage

0.9 − 0.29 − − −

1.1 0.08 − 0.6 0.08 0.6

1.4 0.09 − 0.8 0.09 0.8

1.65 0.15 − 1.0 0.15 1.0

2.3 0.25 − 1.1 0.25 1.1

2.7 0.6 − 1.2 0.6 1.2

V

3.6

3.6

V

CC

Unit

V

V

V

www.onsemi.com

3