ON Semiconductor NC7S08 User manual

TinyLogic HS 2-Input AND Gate

NC7S08

Description

The NC7S08 is a single 2−Input high performance CMOS AND Gate. Advanced Silicon Gate CMOS fabrication assures high speed and low power circuit operation over a broad V protection diodes inherently guard both inputs and output with respect to the V

and GND rails. Three stages of gain between inputs and

CC

outputs assures high noise immunity and reduced sensitivity to input edge rate.

Features

• Space Saving SC−74A and SC−88A 5−Lead Package

• Ultra Small MicroPak™ Leadless Package

• High Speed: t

• Low Quiescent Power: I

• Balanced Output Drive: 2 mA I

• Broad V

CC

= 3.5 ns Typ

PD

< 1 mA

CC

, −2 mA I

OL

Operating Range: 2 V – 6 V

OH

• Balanced Propagation Delays

• Specified for 3 V Operation

• These Devices are Pb−Free, Halogen Free/BFR Free and are RoHS

Compliant

range. ESD

CC

www.onsemi.com

SIP6

CASE 127EB

Pin 1

SC−74A

CASE 318BQ

SC−88A

CASE 419A−02

MARKING

DIAGRAMS

PPKK

XYZ

7S08MG

G

S08MG

G

IEEE / IEC

A B

Figure 1. Logic Symbol

&

Y

PP, 7S08, S08 = Specific Device Code KK = 2−Digit Lot Run Traceability Code XY = 2−Digit Date Code Format Z = Assembly Plant Code M = Date Code*

*Date Code orientation and/or position may

vary depending upon manufacturing location.

ORDERING INFORMATION

See detailed ordering, marking and shipping information in the package dimensions section on page 5 of this data sheet.

January, 2021 − Rev. 4

1 Publication Order Number:

NC7S08/D

Pin Configurations

NC7S08

A

B

GND Y

Figure 2. SC−88A and SC−74A (Top View)

PIN DESCRIPTION

Pin Names Description

A, B Inputs

Y Output

NC No Connect

1

5

V

CC

2

3

4

A 1 6 V

B 2 5 NC

GND 3 4 Y

Figure 3. MicroPak (Top Through View)

FUNCTION TABLE (Y = AB)

Inputs

A B Y

L L L

L H L

CC

Output

H L L

H H H

H = HIGH Logic Level L = LOW Logic Level

ABSOLUTE MAXIMUM RATINGS

Symbol Parameter Min Max Unit

V

CC

I

IK

V

IN

I

OK

V

OUT

I

OUT

ICC or I

T

STG

T

J

T

L

P

D

Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected.

Supply Voltage −0.5 6.5 V

DC Input Diode Current

DC Input Voltage −0.5 V

DC Output Diode Current

DC Output Voltage −0.5 V

VIN < 0 V − −20

V

> V

IN

CC

V

< 0 V − −20

OUT

V

> V

OUT

CC

− +20

CC

− +20

CC

+ 0.5 V

DC Output Source or Sink Current − ±12.5 mA

DC VCC or Ground Current per Output Pin − ±25 mA

GND

Storage Temperature −65 +150 °C

Junction Temperature − +150 °C

Lead Temperature (Soldering, 10 Seconds) − +260 °C

Power Dissipation in Still Air

SC−74A − 390

SC−88A − 332

MicroPak−6 − 812

mA

mW

www.onsemi.com

2

NC7S08

RECOMMENDED OPERATING CONDITIONS

Symbol Parameter Conditions Min Max Unit

V

CC

V

IN

V

OUT

T

tr, t

q

JA

Functional operation above the stresses listed in the Recommended Operating Ranges is not implied. Extended exposure to stresses beyond the Recommended Operating Ranges limits may affect device reliability.

1. Unused inputs must be held HIGH or LOW. They may not float.

DC ELECTICAL CHARACTERISTICS

Symbol Parameter V

V

IH

V

IL

V

OH

V

OL

I

IN

I

CC

Supply Voltage 2.0 6.0 V

Input Voltage 0 V

Output Voltage 0 V

Operating Temperature −40 +85 °C

A

Input Rise and Fall Times

f

VCC at 2.0 V 0 20

VCC at 3.0 V 0 20

VCC at 4.5 V 0 10

VCC at 6.0 V 0 5

Thermal Resistance

SC−74A − 320

SC−88A − 377

MicroPak−6 − 154

TA = +25°C TA = −40 to +85°C

Min Typ Max Min Max

− − 0.7 x V

CC

− 0.3 x V

CC

1.90 2.0 − 1.90 −

HIGH Level Input Voltage

LOW Level Input Voltage

HIGH Level Output Voltage

(V) Conditions

CC

2.0 1.50 − − 1.50 −

3.0 − 6.0 0.7 x V

2.0 − − 0.50 − 0.50

3.0 − 6.0 − − 0.3 x V

2.0 I

3.0 2.90 3.0 − 2.90 −

OH

V

IN

= –20 mA, = V

or V

IH

IL

4.5 4.40 4.5 − 4.40 −

6.0 5.90 6.0 − 5.90 −

= V

IN

= –1.3 mA

= V

IN

= –2 mA

= V

IN

= –2.6 mA

= 20 mA,

= VIH or V

IN

IH

or VIL,

2.68 2.85 − 2.63 −

4.18 4.35 − 4.13 −

5.68 5.85 − 5.63 −

− 0.0 0.10 − 0.10

IL

LOW Level Output Voltage

3.0 V I

OH

4.5 V I

OH

6.0 V I

OH

2.0 I

3.0 − 0.0 0.10 − 0.10

OL

V

4.5 − 0.0 0.10 − 0.10

6.0 − 0.0 0.10 −

3.0 V

4.5 V

6.0 V

Input Leakage Current 6.0 V

Quiescent Supply Current 6.0 V

I

OH

I

OL

I

OL

= V

or VIL,

IN

IH

= 1.3 mA

= V

or VIL,

IN

IH

= 2 mA

= V

or VIL,

IN

IH

= 2.6 mA

= VCC, GND − − ±0.1 − ±1.0

IN

= VCC, GND − − 1.0 − 10.0

IN

− 0.1 0.26 − 0.33

CC

V

ns

°C/W

Unit

V

−

V

CC

V

0.10

mA

www.onsemi.com

3