MT9P004EBMSTCH-GEVB
MT9P004 Evaluation Board
User's Manual
Evaluation Board Overview
The evaluation boards are designed to demonstrate the features of
ON Semiconductor’s image sensors products. This headboard is
intended to plug directly into the Demo 2X system. Test points and
jumpers on the board provide access to clock, I/Os and other
miscellaneous signals.
Features
• Clock Input
♦ Default − 24 MHz crystal oscillator
♦ Optional Demo 2X controlled MClk
• Two Wire Serial Interface
♦ Selectable base address
• Parallel Interface
• MIPI Interface
• ROHS Compliant
www.onsemi.com
EVAL BOARD USER’S MANUAL
Block Diagram
Figure 1. MT9P004 Evaluation Board
Figure 2. Block Diagram of MT9P004EBMSTCH−GEVB
© Semiconductor Components Industries, LLC, 2016
July, 2016 − Rev. 0
1 Publication Order Number:
EVBUM2443/D
Top View
MT9P004EBMSTCH−GEVB
+VDD P11
+2V8_VAA P6
Bottom View
+VDD_PLL P10
+VPP P1
+2V8_VAAPIX P7
+VDD_TX P12
GPI3 P19
GPI0 P16
GPI1 P17
GPI2 P18
EEPROM P14, P15
+VDDIO P9
TEST P2
FLASH P4
SHUTTER P5
RESET Switch SW1
CLK_SELECT P13
ON_LED P8
Figure 3. Top View of Evaluation Board − Default Jumpers
Figure 4. Bottom View of the Evaluation Board − Connector
MIPI Connector J3
Baseboard Connector P36
Baseboard Connector P9
www.onsemi.com
2
MT9P004EBMSTCH−GEVB
Jumper Pin Locations
The jumpers on headboards start with Pin 1 on the leftmost
side of the pin. Grouped jumpers increase in pin size with
each jumper added.
Pin 1
Figure 5. Pin Locations for a Single Jumper.
Pin 1 is Located at the Leftmost Side and Increases as it Moves to the Right
Pin 1
Figure 6. Pin Locations and Assignments of Grouped Jumpers.
Pin 1 is Located at the Top-Left Corner and Increases in a Zigzag Fashion Shown in the Picture
Jumper/Header Functions & Default Positions
Pins 1−4
Pins 1 and 2
Pins 3 and 4
Pins 5 and 6
Pins 7 and 8
Pins 9 and 10
Table 1. JUMPERS AND HEADERS
Jumper/Header No. Jumper/Header Name Pins Description
P1 +VPP Open (Default) For connection to external 6.5~7.0 V +VPP power supply for
P2 TEST
P4 FLASH Open (Default) For connection to external flash
P5 SHUTTER Open (Default) For connection to external shutter
P6 +2V8_VAA
P7 +2V8_VAAPIX
P8 ON_LED
P9 +VDDIO
P10 +VDD_PLL
P11 +VDD
1−2 (Default) Configure to MIPI
2−3 Configure to CCP2
1−2 (Default) Connects to on-board +2V8_VAA power supply
2−3 External power supply connection
1−2 (Default) Connects to on-board +2V8_VAAPIX power supply
2−3 External power supply connection
1−2 (Default) Turn on +5V bus LED indicator
2−3 Turn on +5V bus LED indicator
1−2 (Default) Connects to on-board +VDDIO power supply
2−3 External power supply connection
1−2 (Default) Connects to on-board +VDD_PLL power supply
2−3 External power supply connection
1−2 (Default) Connects to on-board +VDD power supply
2−3 External power supply connection
OTPM
www.onsemi.com
3
MT9P004EBMSTCH−GEVB
Table 1. JUMPERS AND HEADERS (continued)
Jumper/Header No. DescriptionPinsJumper/Header Name
P12 +VDD_TX
P13 CLK_SELECT
P14, P15 EEPROM ADDR
P16 GPI0 Open (Default) For various sensor’s settings/connection to external peripherals
P17 GPI1 Open (Default) For various sensor’s settings/connection to external peripherals
P18 GPI2 Open (Default) For various sensor’s settings/connection to external peripherals
P19 GPI3 Open (Default) For various sensor’s settings/connection to external peripherals
SW1 RESET N/A When pushed, 240 ms reset signal will be sent to MT9P004
1−2 (Default) Connects to on-board +VDD_TX power supply
2−3 (Default) Connects to on-board oscillator
P14 Closed, P15
Open (Default)
P14 Closed,
2−3 External power supply connection
1−2 Connects to XMCLK from Demo 2X Baseboard
EEPROM Address set to 0xA8
P14 Open,
EEPROM Address set to 0xAC
P15 Open
P14 Open,
EEPROM Address set to 0xA4
P15 Closed
EEPROM Address set to 0xA0
P15 Closed
Interfacing to ON Semiconductor Demo 2X Baseboard
The ON Semiconductor Demo 2X baseboard has a similar
26-pin connector and 13-pin connector which mate with P9
ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.
ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent
coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf
ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards,
regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or
specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer
application by customer’s technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not
designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification
in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized
application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such
claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This
literature is subject to all applicable copyright laws and is not for resale in any manner.
. ON Semiconductor reserves the right to make changes without further notice to any products herein.
and P36 of the headboard. The four mounting holes secure
the baseboard and the headboard with spacers and screws.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: orderlit@onsemi.com
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
www.onsemi.com
4
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
EVBUM2443/D
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
ON Semiconductor:
MT9P004EBMSTCH-GEVB
Loading...