Page 1
MatrixCam
I
e
:
,
s
l
QuickStart Guide
Package Contents
1. IoT Camera – 1 Piece
2. LAN Cable – 1 Piece
3. Micro-USB Cable – 1 Piece (One Micro-USB Cable for Power
Supply and/or for Debugging via Terminal Emulator Program)
4. 8 GB SVHC microSDt Card, Class 6 & Adapter – 1 Piece
How Do I Setup My MatrixCam?
1. Plug In the Micro-USB Cable into the Camera (Rear View,
Slot 6) and then into USB Slot in Your PC to Power the
MatrixCam.
2. Plug In the LAN Network Cable into the Camera (Rear View,
Slot 7) and then into Your PC Ethernet RJ45 Slot.
3. Locally , You can Insert a microSD Card (Right-Side View,
Slot 12) to Record/Store Video Images and Snapshots.
www.onsemi.com
1
LED1
2
LED2
LED3
3
4
7
6
8
9
10
Figure 1. MatrixCam Kit
PC Operating Systems and Web-Browsers
Supported
• Windows
®
System (7, 8):
Mozilla Firefox® Version 36 and Up.
5
5
Front View Rear View
• Linux
For video streaming, the MatrixCam GU
®
System: Mozilla Firefox Verison
36 and Up, Ubuntu, 12.4
requires the VLC multimedia player to b
installed, to install VCL 32-bit version go to
www.videolan.org, freeware. On Windows
11
please ensure the web plug-in Active X i
selected during the installation.
2
9
Left-Side View Right-Side View
12
Explanatory Notes:
1 Mic Input
2 LEDs Indicator
3 Lens + AR0230 Digital Image Sensor
4 PIR Sensor
5 Li-Ion Battery Inserted in the MatrixCam Base
Compartment
6 Micro-USB Interface to Power the MatrixCam
from a PC
7 Ethernet RJ45 10/100 Mbps LAN Port
8 Power Button
9 Rotary Arm to Change Tilt of the MatrixCam
10 Speaker
11 Micro-USB Interface for Debugging via Termina
Emulator Program
12 microSD Card Slot
© Semiconductor Components Industries, LLC, 2015
July, 2015 − Rev. 0
1 Publication Order Number:
AND9265/D
Page 2
MatrixCam LAN Network Adapter Settings on Your PC
P
al
k
t
1. Connect the Ethernet cable to your PC −> Go to
Control panel −> Click on Network and Internet
−> Click on Network and Sharing Center −> Click
on Change adapter settings (on the left corner) −>
Click on Change your local LAN network −>
Change your adapter settings:
2. Push the power-on button (rear view, slot 8) −>
Three RED LEDs start glowing −> Wait 2 min −>
Wake up the camera from standby through PIR
(waving or moving hands) −> Wait 30 s for the
connection to establish −> Open up supported web
browser −> enter the IP address of MatrixCam:
192.168.1.168.
Username: admin
Password: admin
3. The GUI log-in page will pop up, after logging in
username and password the video streaming
starts.
4. Change from “admin” password: press “Reset
Password” icon located at the top right corner of
the page.
Firefox is a registered trademark of Mozilla Foundation. Linux is a registered trademark of Linus Torvalds. Windows is a registered trademar
of Microsoft Corporation. microSD is a trademark of SD-3C, LLC in the United States, other countries or both. All other brand names and produc
names appearing in this document are registered trademarks or trademarks of their respective holders.
ON Semiconductor and the are registered trademarks of Semiconductor Components Industries, LLC (SCILLC) or its subsidiaries in the United States and/or other countries.
SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products
for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including
without limitation special, consequential or incidental damages. Should Buyer purchase or use SCILLC products for any unintended or unauthorized application, Buyer shall indemnify
and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising
out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding
the design or manufacture of the part.
UBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: orderlit@onsemi.com
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
www.onsemi.com
2
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your loc
Sales Representative
AND9265/D
Loading...