ON Semiconductor CAT4101 User Manual
CAT4101AGEVB
www.BDTIC.com/ON/
CAT4101 LED Driver
Evaluation Board
User's Manual
http://onsemi.com
EVAL BOARD USER’S MANUAL
Introduction
This document describes the CAT4101AGEVB
evaluation board for the ON Semiconductor CAT4101 low
dropout current sink. The functionality and major
parameters of the CAT4101 can be evaluated with the
CAT4101AGEVB board.
The CAT4101 is a low dropout current sink capable of
driving strings of high-brightness LEDs up to 1 A. The
current sink is programmed by a single resistor from the
RSET pin to GND. Enable and dimming control is available
via the EN/PWM pin. Additional details and electrical
characteristics can be found in the CAT4101 data sheet.
Board Hardware
The evaluation board contains one CAT4101 in a typical
application circuit. A six pin header receptacle is available
to connect strings of LED modules. If LED modules are not
available, a separate LED string can be used by connecting
the cathode end to the LED test point.
The VIN test point is connected to the VIN supply of the
CAT4101. The voltage between test points VIN and GND
should not exceed 6.0 V.
The EN/PWM test point is the enable and PWM input for
the CAT4101. The control signal should be connected
between test points EN/PWM and GND.
Trimmer potentiometer R2 can be adjusted to change the
LED current. The RSET pin of the CAT4101 is a fixed 1.2 V
reference and the LED current is set by changing the current
through the RSET resistor (R1 + R2).
The CAT4101 has a typical dropout voltage of 500 mV for
1 A LED current. To measure the dropout there are kelvin
connections at test points KL and KG. These connections
allow for accurate measurement of the LED pin voltage. At
high current, there could be a significant voltage drop across
board traces. These test points should be used for
measurement purposes only as they are not meant to carry
any current.
Figure 1. CAT4101AGEVB Board
Semiconductor Components Industries, LLC, 2011
September, 2011 − Rev. 1
1 Publication Order Number:
EVBUM2022/D
CAT4101AGEVB
www.BDTIC.com/ON/
LED
1
VIN
GND
EN/PWM
GND
C1
1 mF
R1
560 W
VIN
CAT4101
EN/PWM
RSET
GND
LED
VCC
6
KL
KG
R2
4.7 kW
Figure 2. CAT4101AGEVB Board Schematic
Table 1. CAT4101AGEVB BOARD LIST OF COMPONENTS
Name Manufacturer Description Part Number Units
U1 ON Semiconductor Low Dropout Current Sink, TO-263-5 CAT4101TV 1
C1 Taiyo Yuden
R1 Yageo
R2 Vishay
Tyco 6 Pin Header Receptacle 0.1” Pitch 535676-5 1
Ceramic Capacitor 1 mF/10 V, 10%, X7R, Size 0805
SMT Resistor 1/8 W, 560 W, Size 0805
Trimmer Potentiometer, 4.7 kW
LMK212B7105KD-T 1
RC0805FR-07560RL 1
T63YB472K 1
ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: orderlit@onsemi.com
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5773−3850
http://onsemi.com
2
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
EVBUM2022/D
Loading...