Onkyo TX-SR8450, TX-SR504-B User Manual

AV Receiver

TX-SR504

Contents

Introduction ..................................... 2

Connection .................................... 16

TX-SR504E TX-SR8450

Instruction Manual

Thank you for purchasing an Onkyo AV Receiver. Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new AV Receiver. Please retain this manual for future reference.

Turning On & First Time Setup..... 32

Basic Operation

Playing your AV components ....... 36

Listening to the Radio.................. 38

Enjoying the Listening Modes ..... 48

Advanced Operation..................... 54

Troubleshooting ............................ 62

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

Important Safety Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampliﬁers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not ﬁt into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories speciﬁed by the manufacturer.

12.

Use only with the cart, stand, tripod, bracket, or table speciﬁed by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualiﬁed service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

PORTABLE CART WARNING

S3125A

WARNING

RISK OF ELECTRIC SHOCK

DO NOT OPEN

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to

persons. The exclamation point within an equilateral triangle is

intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

AVIS

RISQUE DE CHOC ELECTRIQUE

NE PAS

OUVRIR

15. Damage Requiring Service Unplug the apparatus from the wall outlet and refer servicing to qualiﬁed service personnel under the following conditions: A. When the power-supply cord or plug is damaged, B. If liquid has been spilled, or objects have fallen

into the apparatus,

C. If the apparatus has been exposed to rain or

water,

D. If the apparatus does not operate normally by

following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualiﬁed technician to restore the apparatus to its normal operation,

E. If the apparatus has been dropped or damaged in

any way, and

F. When the apparatus exhibits a distinct change in

performance this indicates a need for service.

16. Object and Liquid Entry Never push objects of any kind into the apparatus through openings as they may touch dangerous voltage points or short-out parts that could result in a ﬁre or electric shock. The apparatus shall not be exposed to dripping or splashing and no objects ﬁlled with liquids, such as vases shall be placed on the apparatus. Don’t put candles or other burning objects on top of this unit.

17. Batteries Always consider the environmental issues and follow local regulations when disposing of batteries.

18. If you install the apparatus in a built-in installation, such as a bookcase or rack, ensure that there is adequate ventilation. Leave 20 cm (8") of free space at the top and sides and 10 cm (4") at the rear. The rear edge of the shelf or board above the apparatus shall be set 10 cm (4") away from the rear panel or wall, creating a ﬂue-like gap for warm air to escape.

Precautions

1. Recording Copyright

—Unless it’s for personal use only, recording copyrighted material is illegal without the permission of the copyright holder.

2. AC Fuse

—The AC fuse inside the unit is not userserviceable. If you cannot turn on the unit, contact your Onkyo dealer.

3. Care

—Occasionally you should dust the unit all over with a soft cloth. For stubborn stains, use a soft cloth dampened with a weak solution of mild detergent and water. Dry the unit immediately afterwards with a clean cloth. Don’t use abrasive cloths, thinners, alcohol, or other chemical solvents, because they may damage the ﬁnish or remove the panel lettering.

4. Power WARNING

BEFORE PLUGGING IN THE UNIT FOR THE FIRST TIME, READ THE FOLLOWING SECTION CAREFULLY. AC outlet voltages vary from country to country.

Make sure that the voltage in your area meets the voltage requirements printed on the unit’s rear panel (e.g., AC 230–240 V, 50 Hz or AC 120 V, 60 Hz).

Some models have a voltage selector switch for compatibility with power systems around the world. Before you plug in such a model, make sure that the voltage selector is set to the correct voltage for your area. Before you plug in this model, make sure that the voltage selector is set to the correct voltage for your area. If it isn’t, use a small screwdriver to set it as appropriate. For example, if the voltage in your area is 120 volts, set the selector to “120V.” If it’s between 220 and 240 volts, set it to “220-240V.”

DIGITAL IN

COA XIAL

OPTICAL

REMOTE CONTROL

COMPONENT

VIDEO

VIDEO 2 IN

VIDEO 1 IN DVD IN

IN IN

OUT

LRLRL

CD TAPE

OUT

ANTENNA

FMAM75

VIDEO 2 VIDEO 1

VOLTAGE

SELECTOR

IN IN IN

OUT

IN IN

OUT

VIDEO 2 VIDEO 1 DVD

SURROUND BACK

MONITOR

DVD

OUT

SURROUND

CENTER

FRONT

SUB WOOFER

SPEAKERS

SURR BACK

120V

220-240V

FRONT

CENTER

SURROUND

SPEAKERS A

SPEAKER

SPEAKERS

FRONT

SPEAKERS B

PRE OUT

SUB WOOFER

AC OUTLET

VOLTAGE

SWITCHED

SELECTOR

100W

MAX.

120V

220-240V

AV RECEIVER

Pressing the [STANDBY/ON] button to select Standby mode does not fully shutdown the unit. If you do not intend to use the unit for an extended period, remove the power cord from the AC outlet.

5. Never Touch this Unit with Wet Hands—

handle this unit or its power cord while your hands are wet or damp. If water or any other liquid gets inside this unit, have it checked by your Onkyo dealer.

6. Handling Notes

• If you need to transport this unit, use the original

packaging to pack it how it was when you originally bought it.

• Do not leave rubber or plastic items on this unit

for a long time, because they may leave marks on the case.

Never

• This unit’s top and rear panels may get warm after prolonged use. This is normal.

• If you do not use this unit for a long time, it may not work properly the next time you turn it on, so be sure to use it occasionally.

For U.S. models

FCC Information for User

CAUTION:

The user changes or modiﬁcations not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

For Canadian Models

NOTE:

COMPLIES WITH CANADIAN ICES-003. For models having a power cord with a polarized plug:

CAUTION:

MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

THIS CLASS B DIGITAL APPARATUS

TO PREVENT ELECTRIC SHOCK,

Modèle pour les Canadien

REMARQUE:

LA CLASSE B EST CONFORME À LA NORME NMB-003 DU CANADA. Sur les modèles dont la ﬁche est polarisée:

ATTENTION:

TRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.

CET APPAREIL NUMÉRIQUE DE

POUR ÉVITER LES CHOCS ÉLEC-

Precautions

—Continued

Supplied Accessories

For British models

Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualiﬁed service personnel.

IMPORTANT

The wires in the mains lead are coloured in accordance with the following code:

Blue: Neutral Brown: Live

As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black. The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.

IMPORTANT

The plug is ﬁtted with an appropriate fuse. If the fuse needs to be replaced, the replacement fuse must approved by ASTA or BSI to BS1362 and have the same ampere rating as that indicated on the plug. Check for the ASTA mark or the BSI mark on the body of the fuse. If the power cord’s plug is not suitable for your socket outlets, cut it off and ﬁt a suitable plug. Fit a suitable fuse in the plug.

For European Models

Declaration of Conformity

We,

ONKYO EUROPE ELECTRONICS GmbH LIEGNITZERSTRASSE 6, 82194 GROEBENZELL, GERMANY

declare in own responsibility, that the ONKYO product described in this instruction manual is in compliance with the corresponding technical standards such as EN60065, EN55013, EN55020 and EN61000-3-2, -3-3.

GROEBENZELL, GERMANY

Make sure you have the following accessories:

Remote controller and two batteries (AA/R6)

Indoor FM antenna

AM loop antenna

Power-plug adapter

Only supplied in certain countries. Use this adapter if your AC outlet does not match with the plug on the AV receiver’s power cord. (Adapter varies from country to country.)

Left

Front

Right

Zone 2

Surround

SP-B

Zone 2

Front

Left

Front

Right

SP-B

Left

SP-B

Right

Surround

Front

Left

Front

Right

SP-B

Left

SP-B

Right

Speaker Cable

Speaker cable labels

* In catalogs and on packaging, the letter at the end of the

product name indicates the color. Speciﬁcations and operation are the same regardless of color.

Left

Right

Surround

Right

Left

Surround

Right

Surround

Left

Right

Center

Zone 2

Surround Back

Zone 2

Right

Zone 2

Left

Center

Zone 2

Right

Zone 2

Left

Surround Back

Right

Surround Back

Left

Center

Surround Back

Right

Surround Back

Left

K. MIYAGI

ONKYO EUROPE ELECTRONICS GmbH

Features

Ampliﬁer

• 7-channel ampliﬁer

• 75 watts per channel rms into 8 ohms, 2 channels driven, 20 Hz to 20 kHz, less than 0.08% total harmonic distortion (FTC rating)

• WRAT (Wide Range Ampliﬁer Technology)

• Optimum Gain Volume Circuitry

Processing

• Dolby*1 Digital EX and Dolby Pro Logic IIx

• DTS, DTS-ES Matrix/Discrete, DTS Neo:6, and DTS

96/24

• Neural Surround

(North American models only)

• CinemaFILTER function

• Linear PCM 192 kHz/24-bit D/A converters on all channels

• Pure Audio listening mode (not North American model)

•Powerful and highly accurate 32-bit DSP processing

Audio/Video

• Adjustable crossover (40, 50, 60, 80, 100, 120, 150, 200 Hz)

• HDTV-capable component video (3 inputs, 1 output)

•3 S-Video inputs, 2 outputs

•4 assignable digital inputs (3 optical, 1 coaxial)

• Subwoofer pre out

• Color-coded 7.1 multichannel input for use with Super Audio CD and DVD-Audio

• A/B speaker drive

• Color-coded speaker terminal posts

Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic” and the double-D symbol are registered trademarks of Dolby Laboratories.

“DTS,” “DTS 96/24,” “DTS-ES,” and “Neo:6” are trademarks of Digital Theater Systems, Inc.

Neural Surround name and related logos are trademarks owned by Neural Audio Corporation.

Tuner

•XM*4 Satellite Radio (North American models only)

*XM Passport System required; sold separately.

• 40 AM/FM/XM presets

• AM/FM auto tuning

• RDS (Radio Data System) (Europe only)

Remote Controller

• Preprogrammed for use with other AV components

Enjoying Home Theater

Speaker Sets A and B

You can use two sets of speakers with the AV receiver:

Speaker set A

*While speaker set B is on, speaker set A is reduced to 5.1-channel playback.

Speaker set B

*Only analog input sources are output by speaker set B.

should be used in your main listening room for up to 7.1-channel playback.

can be used in another room and offers 2-channel stereo playback.

speaker set A

and

speaker set B

Speaker set A Speaker set B Indicator Output

Off

Off Set A: 7.1 channels

On Set B: 2 channels

Off No sound

A B

AV receiver

SPEAKERS

Remote

controller

Speaker Set A: Main Room

Front left and right speakers

These output the overall sound. Their role in a home theater is to provide a solid anchor for the sound image. They should be positioned facing the listener at about ear level, and equally spaced from the TV. Angle them inward.

Surround back left and right speakers

Center speaker

This speaker enhances the front left and right speakers, making sound movements distinct and providing a full sound image. For movies it’s used mainly for dialog. Position it close to your TV facing forward at about ear level, or at the same height as the front left and right speakers.

Corner

These speakers further enhance the realism of surround sound and improve sound localization behind the listener. Position them behind the listener about 2–3 feet (60–100 cm) above ear level.

Set A: 5.1 channels Set B: 2 channels

* While speaker set B is on, these

speakers output no sound.

Subwoofer

The subwoofer handles the bass sounds of the LFE (LowFrequency Effects) channel. In general, a good bass sound can be obtained by installing the subwoofer in a front corner, or at one-third the way along the wall, as shown.

Speaker Set B: Sub Room

1/3 wall length

Surround left and right speakers

These speakers are used for precise sound positioning and to add realistic ambience. Position them at the sides of the listener, or slightly behind, about 2–3 feet (60–100 cm) above ear level. Ideally they should be equally spaced from the listener.

Introduction

Important Safety Instructions ....................2

Precautions .................................................3

Supplied Accessories.................................4

Features .......................................................5

Enjoying Home Theater..............................6

Speaker Sets A and B ................................... 6

Getting to Know the AV Receiver..............8

Remote Controller.....................................11

Connection

Connecting Your Speakers ......................16

Connecting Antennas...............................18

Connecting Your Components ................20

About AV Connections ................................20

Connecting Audio and Video Signals

to the AV Receiver .................................... 21

Which Connections Should I Use?..............21

TV or Projector DVD player

VCR or DVD Recorder for Playback ...........25

VCR or DVD Recorder for Recording.......... 26

Camcorder, Games Console,

or Other Device.........................................26

Satellite, Cable, Set-top box,

or Other Video Source ..............................27

CD Player or Turntable................................28

HDD-compatible Component ......................29

Cassette, CDR, MiniDisc,

or DAT Recorder.......................................30

Connecting the Power Cord of Another

Component ...............................................30

Connecting Onkyo Components

Connecting the Power Cord ........................31

..........................................22

.................................................23

..........31

Turning On & First Time Setup

Turning On the AV Receiver ....................32

First Time Setup........................................33

Assigning Digital Inputs to Input Sources....33

Changing the Input Display .........................33

Minimum Speaker Impedance Setup

(not North American model)......................34

Speaker Configuration.................................34

Basic Operation

Playing Your AV Components ................ 36

Basic AV Receiver Operation ..................... 36

Using the Multichannel DVD Input.............. 37

Displaying Source Information.................... 37

Listening to the Radio.............................. 38

Listening to AM/FM stations ....................... 38

Presetting AM/FM Stations

and XM Channels..................................... 39

Listening to XM Satellite Radio

(North American Models Only) ................. 42

Common Functions.................................. 46

Setting the Display Brightness.................... 46

Adjusting the Bass and Treble.................... 46

Muting the AV Receiver .............................. 46

Using the Sleep Timer ................................ 47

Using Headphones ..................................... 47

Adjusting Speaker Levels ........................... 47

Enjoying the Listening Modes

Using the Listening Modes...................... 48

Selecting Listening Modes.......................... 48

About the Listening Modes ......................... 50

Using the Late Night Function .................... 52

Using the CinemaFILTER........................... 52

Using the Audio Adjust Settings ................. 52

Advanced Operation

Recording.................................................. 54

Advanced Setup ....................................... 55

Advanced Speaker Settings ....................... 55

Digital Input Signal Formats ....................... 57

Correcting Sound and Picture Sync ........... 58

Controlling Other Components............... 59

Entering Remote Control Codes................. 59

Remote Control Codes for Onkyo

Components Connected via .............. 60

Resetting REMOTE MODE Buttons ........... 60

Resetting the Remote Controller ................ 60

Troubleshooting ....................................... 62

If you can’t resolve an issue, try resetting the AV receiver by holding down the [VIDEO 1] button and pressing the [STANDBY/ON] button.

Specifications ........................................... 66

Getting to Know the AV Receiver

Front Panel

North American Model

3 5 6 74

STANDBY/ON

PHONES

Other Models

STANDBY/ON

PURE AUDIO

PHONES

STANDBY

DVDMULTI CH C

VCR

SPEAKERS

TONE

DVDMULTI CH C

VCR

TONE

VIDEO

3VIDEO 2VIDEO 1

LISTENING MODE

3VIDEO 2VIDEO 1

LISTENING MODE

TUNERTAPE

DIGITAL

DISPLAYSTEREO DIMMER MEMORY

INPUT

TUNERTAPE

DIGITAL

DISPLAYSTEREO RT/PTY/TP MEMORY

INPUT

CLEAR

TUNING

MODE

CLEAR

TUNING PRESET

TUNING MODE

MASTER VOLUME

ENTER

SETUPRETURN

VIDEO 3 INPUT

VIDEO

AUDIOLR

TJKLMNOPQ8 9RS

MASTER VOLUME

ENTER

SETUPRETURN

VIDEO 3 INPUT

VIDEO

AUDIOLR

For detailed information, see the pages in parentheses.

STANDBY/ON button (32)

Sets the AV receiver to On or Standby.

STANDBY indicator (32)

Lights up when the AV receiver is on Standby and ﬂashes while a signal is being received from the remote controller.

Remote-control sensor (11)

Receives control signals from the remote controller.

Display

See “Display” on page 9.

Input selector buttons (36)

Select the input sources. The [MULTI CH] button selects the multichannel

DVD input.

(European model only)

Arrow/TUNING/PRESET and ENTER buttons

When AM, FM, or XM is selected, the TUNING [] [ ] buttons are used for radio tuning, and the PRESET [ ] [ ] buttons are used to select radio

presets (see page 39). With the setup menus, they work as arrow buttons and are used to select and set items. The ENTER button is also used with the setup menus.

MASTER VOLUME control (36)

Sets the volume of the AV receiver to MIN, 1 through 79, or MAX.

PHONES jack (47)

This 1/4-inch phone jack is for connecting a standard pair of stereo headphones for private listening.

SPEAKERS A and B buttons (6, 36)

Turn speaker sets A and B on or off.

Getting to Know the AV Receiver

—Continued

TONE, [–], and [+] buttons (46)

Used to adjust the bass and treble.

STEREO button (48)

Selects the Stereo listening mode.

LISTENING MODE [ ]/[ ] buttons (48)

Select the listening modes.

DISPLAY button (37)

Displays various information about the currently selected input source.

DIGITAL INPUT button (33, 57)

Used to assign the digital inputs and to specify the format of digital input signals.

DIMMER or RT/PTY/TP button (41, 46)

Adjusts the display brightness. On the European model, this is the RT/PTY/TP but-

ton, and it’s used with RDS (Radio Data System). See “Using RDS (European Models Only)” on page 40.

Display

MEMORY button (39)

Used when storing or deleting radio presets.

TUNING MODE button (38)

Selects the Auto or Manual tuning mode for AM and FM radio.

RETURN button

Selects the previously displayed setup menu.

SETUP button

Used to access the setup menus.

VIDEO 3 INPUT (26, 54)

Used to connect a camcorder, games console, and so on. There are jacks for composite video and analog audio.

PURE AUDIO button and indicator (48)

The North American model doesn’t have this button and indicator.

Selects the Pure Audio listening mode. The indicator lights up when this mode is selected.

2134

For detailed information, see the pages in parentheses.

A and B speaker indicators (6, 36)

Indicator A lights up when speaker set A is on. Indicator B lights up when speaker set B is on.

MUTING indicator (46)

Flashes while the AV receiver is muted.

Listening mode and format indicators (50)

Show the selected listening mode and the format of digital audio signals.

Radio indicators

TUNED (38):

tion.

AUTO (38):

Auto Tuning is selected, and disappears when Manual Tuning mode is selected.

RDS (European models only) (40):

when tuned to a radio station that supports RDS (Radio Data System).

Lights up when tuned to a radio sta-

For AM and FM radio, lights up when

Lights up

XM (North American models only) (42):

Lights up when XM radio is selected.

MEMORY (39):

stations.

FM STEREO (38):

reo FM station.

SLEEP indicator (47)

Lights up when the Sleep function has been set.

Message area

Displays various information about the selected input source.

Lights up when presetting radio

Lights up when tuned to a ste-

Getting to Know the AV Receiver

Rear Panel

(North American model only)

B 8

4 53 6

—Continued

(Only some models)

COA XIAL

OPTICAL

DIGITAL IN

REMOTE CONTROL

VIDEO 2 IN

COMPONENT

VIDEO 1 IN DVD IN

IN IN

CD TAPE

VIDEO

OUT

LRL

ANTENNA

FMAM75

VIDEO 2 VIDEO 1

IN IN IN

OUT

IN IN

OUT

VIDEO 2 VIDEO 1 DVD

9 J K L M N P

DIGITAL IN OPTICAL 1, 2, 3, and COAXIAL

These optical and coaxial digital audio inputs are for connecting components with optical or coaxial digital audio outputs, such as CD and DVD players.

XM antenna (on North American models)

This jack is for connecting an XM Passport System, sold separately (see page 42).

COMPONENT VIDEO

A DVD player, TV, or other component that supports component video can be connected here.

AM ANTENNA

These push terminals are for connecting an AM antenna.

FM ANTENNA

This jack is for connecting an FM antenna.

MONITOR OUT

The S-Video or composite video output should be connected to a video input on your TV or projector.

FRONT SPEAKERS A, SURROUND SPEAKERS, CENTER SPEAKER, and SURROUND BACK SPEAKERS

These terminal posts are for connecting speaker set A.

VOLTAGE SELECTOR (Only some models)

This voltage selector provides compatibility with power systems around the world (see page 3).

REMOTE CONTROL

This Remote Interactive jack can be connected to the jack on another -capable Onkyo component. To use , you must make an analog audio

connection (RCA) between the AV receiver and the other component, even if they are connected digitally.

SURROUND BACK

SPEAKERS

MONITOR

DVD

OUT

FRONT

SURROUND

SURR BACK

CENTER

SUB WOOFER

SURROUND SPEAKERS

PRE OUT

SUB WOOFER

FRONT

SPEAKERS A

FRONT

SPEAKERS B

CENTER SPEAKER

AC OUTLET

AV RECEIVER

VOLTAGE

SELECTOR

120V

220-240V

AC 120V

SWITCHED

TOTAL120W

60Hz

1A MAX.

CD IN

This analog audio input is for connecting a CD player’s analog audio output.

TAPE IN/OUT

This analog audio input and output are for connecting a recorder with an analog audio input and output, such as a cassette deck, MD recorder, etc.

VIDEO 1 IN/OUT and VIDEO 2 IN

The VIDEO 1 inputs and outputs can be used to connect a VCR. The VIDEO 2 inputs can be used to connect another video source (e.g., cable/satellite receiver, set-top box, etc).

DVD IN

These jacks can be used to connect a DVD player with an analog multichannel audio output for SACD and DVD-Audio playback.

SUBWOOFER PRE OUT

A powered subwoofer can be connected here.

FRONT SPEAKERS B

These push terminals are for connecting speaker set B.

AC OUTLET

This switched AC outlet can be used to supply power to another AV component. The type of outlet depends on the country in which you purchased your AV receiver.

See pages 16–31 for hookup information.

Remote Controller

Installing the Batteries

To open the battery compartment, press

the small hollow and slide open the cover.

Insert the two supplied batteries (AA/R6)

in accordance with the polarity diagram inside the battery compartment.

Slide the cover shut.

Notes:

• If the remote controller doesn’t work reliably, try replacing the batteries.

• Don’t mix new and old batteries or different types of batteries.

• If you intend not to use the remote controller for a long time, remove the batteries to prevent damage from leakage or corrosion.

• Expired batteries should be removed as soon as possible to prevent damage from leakage or corrosion.

Aiming the Remote Controller

When using the remote controller, point it toward the AV receiver’s remote control sensor, as shown below.

Remote control sensor

AV receiver

STANDBY indicator

Approx. 16 ft. (5 m)

Notes:

• The remote controller may not work reliably if the AV receiver is subjected to bright light, such as direct sunlight or inverter-type ﬂuorescent lights. Keep this in mind when installing.

• If another remote controller of the same type is used in the same room, or the AV receiver is installed close to equipment that uses infrared rays, the remote controller may not work reliably.

• Don’t put anything on top of the remote controller, such as a book or magazine, because a button may be pressed continuously, thereby draining the batteries.

• The remote controller may not work reliably if the AV receiver is installed in a rack behind colored glass doors. Keep this in mind when installing.

• The remote controller will not work if there’s an obstacle between it and the AV receiver’s remote control sensor.

Remote Controller

—Continued

Using the Remote Controller

Including the AV receiver, the remote controller can be used to control up to seven different components. The remote controller has a speciﬁc operating mode for use with each type of component. Modes are selected by using the six REMOTE MODE buttons.

■

RECEIVER/TAPE Mode

In RECEIVER/TAPE mode, you can control the AV receiver and an Onkyo cassette recorder connected via .

■

DVD and CD/MD/CDR/HDD Modes

With these modes, you can control a DVD player and CD, MD, CDR, or HDD player or recorder. By entering the appropriate remote control code, you can control Onkyo components or components made by other manufacturers (see page 59).

■

TV, VCR and SAT/CABLE Modes

With these modes, you can control a TV, VCR, and satellite or cable receiver. You must enter the appropriate remote control code ﬁrst (see page 59).

REMOTE MODE

RECEIVER

TAPE

Press one of the REMOTE MODE buttons to select a mode.

DVD

M D/CDR

HDD

VCR

CABLE

SAT

RECEIVER

TAPE

DVD

M D/CDR

HDD

VCR

CABLE

SAT

RECEIVER/TAPE Mode

RECEIVER/TAPE mode is used to control the AV receiver. It can also be used to control an Onkyo cassette recorder connected via .

RECEIVER

TAPE

ON/STANDBY

INPUT SELECTOR

123

456

789

10 11 12

D TUN

--/---

INPUT

GUIDE

TOP MENU

SP A / B

PLAYLIST/CAT PLAYLIST/CAT

V2V

MULTI CH

DIMMER

VOL

REMOTE MODE

RECEIVER

TAPE

DVD

ENT

SLEEP

ALBUM

ENTER

C DTAPE TUNER

CLR

DISC

DVD

D/CDR

C D

HDD

VCR

CABLE

SAT

VOL

MUTING

SETUPRETURN

LISTENING MODE

SURROUND

STEREO

RANDOM

SUBTITLE

AUDIO REPEAT

TEST TONE

CH SEL

PLAY MODE

DISPLAY

LEVEL

L NIGHT

LEVEL

CINE FLTR

HDDDVDVCR

P Q

Use the buttons supported by that mode to control the component.

RECEIVER/TAPE mode:

see right column

DVD mode:

see page 14

CD/MD/CDR/HDD mode:

see page 15

TV, VCR, SAT/CABLE modes:

see page 61

Note:

Some of the remote controller operations described in this manual may not work as expected with other components.

Buttons

1, 2, 3

, and 4 are used when the TUNER

or TAPE input is selected.

647M

Remote Controller

—Continued

For detailed information, see the pages in parentheses.

ON/STANDBY button (32)

Sets the AV receiver to On or Standby.

INPUT SELECTOR buttons (36)

Used to select the input sources.

MULTI CH button (37)

Selects the multichannel DVD input.

DIMMER button (46)

Adjusts the display brightness.

SP A/B button (6, 36)

Used to turn speaker sets A and B on or off.

Arrow [ ]/[ ]/[ ]/[ ] and ENTER buttons

Used to select and adjust settings.

RETURN button

Selects the previously displayed setup menu.

LISTENING MODE buttons (48)

Used to select the listening modes. These buttons work in all remote controller modes.

STEREO button

Selects the Stereo listening mode.

SURROUND button

Selects the Dolby and DTS listening modes and the Neural Surround listening mode (North American model only).

[ ]/[ ] buttons

Used to select the available listening modes.

TEST TONE, CH SEL, LEVEL-, and LEVEL+ buttons (35, 47, 57)

Used to adjust the level of each speaker.

DISPLAY button (37)

Displays various information about the selected input source.

REMOTE MODE buttons (12)

Used to select the remote controller modes. When a remote controller button is pressed, the REMOTE MODE button for the currently selected mode lights up.

SLEEP button (47)

Used with the Sleep function.

VOL [ ]/[ ] button (36)

Adjusts the volume of the AV receiver regardless of the currently selected remote controller mode.

MUTING button (46)

Mutes or unmutes the AV receiver.

SETUP button

Used to access the setup menus.

CINE FLTR button (52)

Used with the CinemaFILTER function.

L NIGHT button (52)

Used with the Late Night function.

■

Buttons used when the TUNER input is selected

To select the Tuner (AM/FM/XM) as the input source, press:

RECEIVER

Number, D TUN, and ENT buttons (39, 43)

Used to select AM and FM radio stations and XM radio channels directly.

CH +/– button (39)

Used to select radio presets.

Arrow [ ]/[ ]/[ ]/[ ] and ENTER buttons

For AM and FM, the Up and Down [ ]/[ ] buttons are used for tuning.

North American model only

For XM, the Up and Down [ ]/[ ] buttons are used to select channels, and the [ENTER] button is used to change the search mode. The Left and Right

[ ]/[ ] buttons are used to select categories.

■

Buttons used when the TAPE input is selected

To select your Cassette deck as the input source, press:

RECEIVER

Playback buttons

On twin cassette decks, only deck B can be controlled.

Play [ ] button

Starts playback.

Stop [ ] button

Stops playback.

Reverse Play [ ] button

Starts reverse playback.

Rewind and FF [ ]/[ ] buttons

The Rewind [ ] button starts rewind. The FF [] button starts fast forward.

TUNER

TAPE

Remote Controller

—Continued

DVD Mode

By default, the remote controller is set to control an Onkyo DVD player.

To select your DVD player as the input source, press:

DVD

REMOTE MODE

RECEIVER

TAPE

DVD

C DTAPE TUNER

CLR

ENT

SLEEP

DISC

ALBUM

ENTER

MULTI CH

DVD

D/CDR

C D

HDD

VCR

CABLE

SAT

DVD

VOL

MUTING

SETUPRETURN

RECEIVER

ON/STANDBY

INPUT SELECTOR

123

V1V2V

456

MULTI CH

789

10 11 12

D TUN

--/---

DIMMER

VOL

INPUT

GUIDE

TOP MENU

SP A / B

PLAYLIST/CAT PLAYLIST/CAT

LISTENING MODE

SURROUND

8 9

STEREO

RANDOM

SUBTITLE

AUDIO REPEAT

TEST TONE

CH SEL

PLAY MODE

DISPLAY

LEVEL

L NIGHT

LEVEL

CINE FLTR

HDDDVDVCR

N O

647M

ON/STANDBY button

Sets the DVD player to On or Standby.

Number buttons

Used to enter title, chapter, and track numbers and times for locating speciﬁc points.

DISC +/– button

Selects discs on a DVD changer.

TOP MENU button

Selects a DVD’s top menu.

Arrow [ ]/[ ]/[ ]/[ ] and ENTER buttons

Used to navigate DVD menus and the DVD player’s onscreen setup menus.

RETURN button

Exits the DVD player’s onscreen setup menus.

Playback buttons

From left to right: Pause, Play, Stop, Fast Reverse, Fast Forward, Previous, and Next.

SUBTITLE button

Selects subtitles.

AUDIO button

Selects foreign language soundtracks and audio formats (e.g., Dolby Digital or DTS).

DISPLAY button

Displays information about the current disc, title, chapter, or track, including elapsed time, remaining time, total time, and so on.

CLR button

Cancels functions and clears entered numbers.

MENU button

Displays a DVD’s menu.

SETUP button

Used to access the DVD player’s onscreen setup menus.

RANDOM button

Used with the random playback function.

REPEAT button

Used with the repeat playback functions.

VCR, DVD, and HDD buttons

Used to select VCR, HDD (hard disk drive), or DVD playback on a VCR/DVD recorder with a built-in hard disk drive.

PLAY MODE button

Selects play modes on components with selectable play modes.

Remote Controller

—Continued

CD/MD/CDR/HDD Mode

By default, the remote controller is set to control an Onkyo CD player.

To select the input source, press:

C D

RECEIVER

TAPE

* If you’re using an MD, CDR, or HDD component, you

must change the Input Display (see page 33).

ON/STANDBY

INPUT SELECTOR

123

V1V

456

MULTI CH

789

10 11 12

D TUN

--/---

DIMMER

VOL

INPUT

GUIDE

TOP MENU

SP A / B

PLAYLIST/CAT PLAYLIST/CAT

CD player

MD or CD recorder

Next generation HDD-

compatible component

REMOTE MODE

DVD

RECEIVER

TAPE

D/CDR

C D

HDD

DVD

VCR

C DTAPE TUNER

CABLE

SAT

CLR

ENT

SLEEP

DISC

VOL

ALBUM

MUTING

ENTER

SETUPRETURN

M D/CDR

C D

HDD

ON/STANDBY button

Sets the component to On or Standby.

Number buttons

Used to enter track numbers and times for locating speciﬁc points on CD/MD players.

DISC/ALBUM +/– button

Selects discs on a CD changer, or the next or previous album on an HDD-compatible component.

Arrow [ ]/[ ] and ENTER buttons

Used to navigate menus on an HDD-compatible component.

Playback buttons

From left to right: Pause, Play, Stop, Fast Reverse, Fast Forward, Previous and Next.

DISPLAY button

Displays information about the current disc or track on a CD player or MD/CD recorder, including elapsed time, remaining time, total time, and so on. On an HDD-compatible component, it turns on the back light for 30 seconds.

CLR button

Cancels functions and clears entered numbers on a CD player or MD/CD recorder.

MENU button

Used to navigate menus on an HDD-compatible component.

PLAYLIST [ ]/[ ] buttons

Selects the previous or next playlist on an HDDcompatible component.

RANDOM button

Used with the random/shufﬂe playback function.

REPEAT button

Used with the repeat playback functions.

PLAY MODE button

Used to select play modes on components with selectable play modes.

LISTENING MODE

SURROUND

STEREO

RANDOM

SUBTITLE

AUDIO REPEAT

TEST TONE

CH SEL

PLAY MODE

DISPLAY

LEVEL

CINE FLTR

L NIGHT

HDDDVDVCR

647M

Connecting Your Speakers

Speaker Conﬁguration

For the best surround-sound experience, you should connect seven speakers and a powered subwoofer.

The following table shows which channels you should use based on the number of speakers that you have.

Number of speakers: 234567

Front left

Front right

Center

Surround left

Surround right

Surround back*

Surround back left

Surround back right

*If you’re using only one surround back speaker, connect it to the left (L) SURROUND BACK SPEAKERS terminals.

✓✓✓✓✓✓

✓ ✓✓✓

✓✓✓✓

✓

No matter how many speakers you use, a powered subwoofer is recommended for a really powerful and solid bass.

Before using the AV receiver, you must specify which speakers are connected and their sizes (see page 34).

To get the very best from your surround-sound system, you should also set the advanced speaker settings (see page 55.)

Attaching the Speaker Labels

The AV receiver’s positive (+) speaker terminals are color-coded for ease of identiﬁcation. (The negative (–) speaker terminals are all black.)

Speaker terminal Color

Front left White

Front right Red

Center Green

Surround left Blue

Surround right Gray

Surround back left Brown

Surround back right Tan

The supplied speaker labels are also color-coded and you should attach them to the positive (+) side of each speaker cable in accordance with the above table. All you need to do then is to match the color of each label to the corresponding speaker terminal.

Speaker Connection Precautions

Read the following before connecting your speakers:

•

North American models:

with an impedance of between 6 and 16 ohms. If you use speakers with a lower impedance, and use the ampliﬁer at high volume levels for a long period of time, the built-in amp protection circuit may be activated.

•

Other models:

You can connect speakers with an impedance of between 4 and 16 ohms. If the impedance of any of the connected speakers is 4 ohms or more, but less than 6 ohms, be sure to set the minimum speaker impedance to “4 ohms” (see page 34). If you use speakers with a lower impedance, and use the ampliﬁer at high volume levels for a long period of time, the built-in amp protection circuit may be activated.

• Disconnect the power cord from the wall outlet before making any connections.

• Read the instructions supplied with your speakers.

•Pay close attention to speaker wiring polarity. In other words, connect positive (+) terminals to only positive (+) terminals, and negative (–) terminals to only negative (–) terminals. If you get them the wrong way around, the sound will be out of phase and will sound unnatural.

• Unnecessarily long or very thin speaker cables may affect the sound quality and should be avoided.

• Be careful not to short the positive and negative wires. Doing so may damage the AV receiver.

• Don’t connect more than one cable to each speaker terminal. Doing so may damage the AV receiver.

• Don’t connect a speaker to several terminals.

You can connect speakers

Connecting Your Speakers

—Continued

Connecting Speaker Set A

Strip 5/8" (15 mm) of insu-

lation from the ends of the speaker cables, and twist the bare wires tightly, as shown.

Unscrew the terminal. Fully insert the bare wire,

making sure that it’s touching the threaded shaft in the center. Screw the terminal tight.

5/8" (15 mm)

Connecting a Powered Subwoofer

Using a suitable cable, connect the AV receiver’s SUBWOOFER PRE OUT to the input on your powered subwoofer. If your subwoofer is unpowered and you’re using an external ampliﬁer, connect the SUBWOOFER PRE OUT to it’s input.

Note:

Make sure the plugs are pushed in all the way.

Connecting Speaker Set B

Strip 3/8" (10 mm) of insu-

lation from the ends of the speaker cables, and twist the bare wires tightly, as shown.

While pressing the lever, insert

the wire into the hole, and then release the lever.

Make sure that the terminals are gripping the bare wires, not the insulation.

Note:

While speaker set B is on, speaker set A is reduced to

5.1-channel playback.

Speaker Set A

Front right

speaker

3/8" (10 mm)

Front left

speaker

The following illustration shows which speaker should be connected to each pair of terminals.

If you’re using only one surround back speaker, connect it to the left (L) SURROUND BACK SPEAKERS terminals.

DIGITAL IN

COA XIAL

OPTICAL

REMOTE CONTROL

COMPONENT

VIDEO 2 IN

VIDEO 1 IN DVD IN

IN IN

CD TAPE

Front right

ANTENNA

VIDEO

OUT

VIDEO 2 VIDEO 1

IN IN IN

OUT

IN IN

OUT

LRL

OUT

VIDEO 2 VIDEO 1 DVD

speaker

Speaker Set B

FMAM75

MONITOR

DVD

OUT

SURROUND

FRONT

Front left

speaker

CENTER

SUB WOOFER

SURROUND BACK

SPEAKERS

SURR BACK

SURROUND

FRONT

SPEAKERS

CENTER

SPEAKERS A

SPEAKER

AV RECEIVER

AC OUTLET

AC 120V

SWITCHED

TOTAL120W 1A MAX.

LINE INPUT

60Hz

FRONT

SPEAKERS B

PRE OUT

SUB WOOFER

Powered

subwoofer

SURROUND BACK

SPEAKERS

Surround

back right

speaker

SURROUND SPEAKERS

Surround

back left speaker

Center

speaker

FRONT

SPEAKERS A

CENTER

SPEAKER

Surround

right

speaker

Surround

left

speaker

Connecting Antennas

This section explains how to connect the supplied indoor FM antenna and AM loop antenna, and how to connect commercially available outdoor FM and AM antennas.

The AV receiver won’t pick up any radio signals without any antenna connected, so you must connect the antenna to use the tuner.

AM antenna push terminals FM antenna jack

DIGITAL IN

COA XIAL

OPTICAL

REMOTE CONTROL

COMPONENT

VIDEO

VIDEO 2 IN

VIDEO 1 IN DVD IN

IN IN

OUT

LRLRL

CD TAPE

OUT

ANTENNA

FMAM75

VIDEO 2 VIDEO 1

DVD

IN IN IN

OUT

IN IN

FRONT

OUT

VIDEO 2 VIDEO 1 DVD

SURROUND BACK

MONITOR

OUT

SURROUND

CENTER

SUB WOOFER

FRONT

CENTER

SURROUND

SPEAKERS A

SPEAKERS

SURR BACK

SPEAKER

SPEAKERS

FRONT

SPEAKERS B

PRE OUT

SUB WOOFER

AC OUTLET

AC 120V

60Hz

SWITCHED

TOTAL120W 1A MAX.

AV RECEIVER

Connecting the Indoor FM Antenna

The supplied indoor FM antenna is for indoor use only.

Attach the FM antenna, as shown.

■

American Model

Insert the plug fully into the jack.

Connecting the AM Loop Antenna

The supplied indoor AM loop antenna is for indoor use only.

Assemble the AM loop antenna, inserting

the tabs into the base, as shown.

Connect both wires of the AM loop

antenna to the AM push terminals, as shown.

(The antenna’s wires are not polarity sensitive, so they can be connected either way around).

Make sure that the wires are attached securely and that the push terminals are gripping the bare wires, not the insulation.

Push Insert wire Release

■

Other Models

Insert the plug fully into the jack.

Once your AV receiver is ready for use, you’ll need to tune into an FM radio station and adjust the position of the FM antenna to achieve the best possible reception.

Use thumbtacks or something similar to

ﬁx the FM antenna into position.

Thumbtacks, etc.

Caution:

Be careful that you don’t injure yourself

when using thumbtacks.

Once your AV receiver is ready for use, you’ll need to tune into an AM radio station and adjust the position of the AM antenna to achieve the best possible reception.

Keep the antenna as far away as possible from your AV receiver, TV, speaker cables, and power cords.

If you cannot achieve good reception with the supplied indoor AM loop antenna, try using it with a commercially available outdoor AM antenna (see page 19).

If you cannot achieve good reception with the supplied indoor FM antenna, try a commercially available outdoor FM antenna instead (see page 19).

Connecting Antennas

—Continued

Connecting an Outdoor FM Antenna

If you cannot achieve good reception with the supplied indoor FM antenna, try a commercially available outdoor FM antenna instead.

FM 75

Notes:

• Outdoor FM antennas work best outside, but usable results can sometimes be obtained when installed in an attic or loft.

•For best results, install the outdoor FM antenna well away from tall buildings, preferably with a clear line of sight to your local FM transmitter.

• Outdoor antenna should be located away from possible noise sources, such as neon signs, busy roads, etc.

•For safety reasons, outdoor antenna should be situated well away from power lines and other high-voltage equipment.

• Outdoor antenna must be grounded in accordance with local regulations to prevent electrical shock hazards.

■

Using a TV/FM Antenna Splitter

It’s best not to use the same antenna for both FM and TV reception, as this can cause interference problems. If circumstances demand it, use a TV/FM antenna splitter, as shown.

Connecting an Outdoor AM Antenna

If good reception cannot be achieved using the supplied AM loop antenna, an outdoor AM antenna can be used in addition to the loop antenna, as shown.

Outdoor antenna

Insulated antenna cable

AM loop antenna

Outdoor AM antennas work best when installed horizontally outside, but good results can sometimes be obtained indoors by mounting horizontally above a window. Note that the AM loop antenna should be left connected.

Outdoor antenna must be grounded in accordance with local regulations to prevent electrical shock hazards.

TV/FM antenna splitter

To AV receiver To TV (or VCR)

Connecting Your Components

About AV Connections

• Before making any AV connections, read the manuals supplied with your other AV components.

• Don’t connect the power cord until you’ve completed and double-checked all AV connections.

Optical Digital Jacks

The AV receiver’s optical digital jacks have shutter-type covers that open when an optical plug is inserted and close when it’s removed. Push plugs in all the way.

Caution:

plug straight when inserting and removing.

AV Cables and Jacks

To prevent shutter damage, hold the optical

Video

Cable Jack Description

Component video cable

S-Video cable

Composite video cable

AV Connection Color Coding

RCA-type AV connections are usually color coded: red, white, and yellow. Use red plugs to connect right-channel audio inputs and outputs (typically labeled “R”). Use white plugs to connect left-channel audio inputs and outputs (typically labeled “L”). And use yellow plugs to connect composite video inputs and outputs.

Left (white)

Right (red)

(Yellow)

• Push plugs in all the way to make good connections (loose connections can cause noise or malfunctions).

•To prevent interference, keep audio and video cables away from power cords and speaker cables.

Component video separates the luminance (Y) and color difference signals (PR, PB), providing the best picture quality. (Some TV manufacturers label their component video jacks slightly differently.)

S-Video separates the luminance and color signals

and provides better picture quality than composite video.

Composite video is commonly used on TVs, VCRs,

and other video equipment. Use only dedicated composite video cables.

Analog audio

Composite video

Left (white)

Right (red)

(Yellow)

Right!

Wrong!

Audio

Cable Jack Description

Optical digital audio cable

Coaxial digital audio cable

Analog audio cable (RCA)

Multichannel analog audio cable (RCA)

Note:

The AV receiver does not support SCART connections.

COA XIAL

OPTICAL

This offers the best sound quality and allows you to enjoy Dolby Digital and DTS. The audio quality is the same as for coaxial.

This offers the best sound quality and allows you to enjoy Dolby Digital and DTS. The audio quality is the same as for optical.

This cable carries analog audio. It’s the most common connection format for analog audio and can be found on virtually all AV components.

This cable carries multichannel analog audio and is typically used to connect DVD players with a 7.1channel analog audio output. Several standard analog audio cables can be used instead of a multichannel cable.

Connecting Your Components

—Continued

Connecting Audio and Video Signals to the AV Receiver

By connecting both the audio and video outputs of your DVD player and other AV components to the AV receiver, you can switch the audio and video signals simultaneously simply by changing the input source on the AV receiver.

: Signal Flow

Video

Audio

Speakers (see page 17 for hookup details)

DVD player, etc.

Audio

TV, projector, etc.

Which Connections Should I Use?

The AV receiver supports several connection formats for compatibility with a wide range of AV equipment. The format you choose will depend on the formats supported by your other components. Use the following sections as a guide.

For video components, such as a DVD player, you must make an audio connection and a video connection.

Video Connection Formats

When choosing a connection format, bear in mind that the AV receiver doesn’t convert between formats, so only outputs of the same format as the input will output the signal.

Video Signal Flow Chart

DVD player,

etc.

Output

AV Receiver

OUT

Input

TV,

projector,

etc.

Composite

S-Video

Component

Audio Connection Formats

When choosing a connection format, bear in mind that the AV receiver doesn’t convert between formats.

For example, audio signals connected to an OPTICAL or COAXIAL digital input are not output by the analog TAPE OUT, so if you want to record from, for example, your CD player, in addition to connecting it to a digital input, you must also connect it to the analog CD IN.

Audio Signal Flow Chart

CD player,

etc.

Output

AV Receiver

OUT

Input

Cassette

recorder, etc.

Optical

Coaxial

Analog

Multichannel

Connecting Your Components

cab

—Continued

Connecting a TV or Projector

Step 1: Video Connection

Choose a video connection that matches your TV ( , , or ), and then make the connection.

Step 2: Audio Connection

Choose an audio connection that matches your TV ( , , or ), and then make the connection.

A B

a b c

•With connection , you can listen to and record audio from your TV and listen via speaker set B.

•To enjoy Dolby Digital and DTS, use connection or . (For recording, use and , or and .)

a c

Connection AV receiver Signal ﬂow TV Picture quality

COMPONENT VIDEO OUT

MONITOR OUT S

MONITOR OUT V

VIDEO 2 IN L/R

DIGITAL IN COAXIAL

DIGITAL IN OPTICAL 2

DIGITAL IN

COA XIAL

OPTICAL

REMOTE CONTROL

VIDEO 2 IN

COMPONENT

VIDEO 1 IN DVD IN

IN IN

CD TAPE

VIDEO

OUT

⇒

⇐

OUT

Component video input

S-Video input Better

Composite video input

Analog audio L/R output

Digital coaxial output

Digital optical output

ANTENNA

FMAM75

VIDEO 2 VIDEO 1

IN IN IN

IN IN

VIDEO 2 VIDEO 1 DVD

DVD

OUT

FRONT

OUT

MONITOR

OUT

SURROUND

SURROUND BACK

SPEAKERS

CENTER

SUB WOOFER

SURR BACK

Best

Standard

PRE OUT

SUB WOOFER

FRONT

SPEAKERS A

SURROUND SPEAKERS

SPEAKERS B

FRONT

R S VIDEO

AUDIO

OUT

VIDEO

OUT

OPTICAL

OUT

YCOAXIAL

COMPONENT VIDEO IN

Connect one or the other Connection must be assigned (see page 33)

TV, projector, etc.

If your TV has no audio outputs, connect an audio output from your VCR or cable or satellite

Hint!

receiver to the AV receiver and use its tuner to listen to TV programs through the AV receiver (see pages 25 and 27).

Connecting Your Components

—Continued

Connecting a DVD player

Step 1: Video Connection

Choose a video connection that matches your DVD player ( , , or

A B C

You must connect the AV receiver to your TV via the same type of connection.

Step 2: Audio Connection

Choose an audio connection that matches your DVD player ( , , or ), and then make the connection.

), and then make the connection.

b c

•With connection , you can listen to and record audio from a DVD and listen via speaker set B.

•To enjoy Dolby Digital and DTS, use connection or . (For recording, use and , or and .)

b c a b a c

• If your DVD player has main left and right outputs and multichannel left and right outputs, be sure to use the main left and right outputs for connection .

Connection AV receiver Signal ﬂow DVD player Picture quality

COMPONENT VIDEO DVD IN

DVD IN S

DVD IN V

DVD IN FRONT

DIGITAL IN COAXIAL

DIGITAL IN OPTICAL 1

DIGITAL IN

COA XIAL

OPTICAL

REMOTE CONTROL

VIDEO 2 IN

COMPONENT

VIDEO 1 IN DVD IN

IN IN

CD TAPE

OUT

VIDEO

⇐

OUT

Component video output

S-Video output Better

Composite video output

Analog audio L/R output

Digital coaxial output

Digital optical output

ANTENNA

FMAM75

VIDEO 2 VIDEO 1

IN IN IN

IN IN

VIDEO 2 VIDEO 1 DVD

DVD

OUT

FRONT

OUT

MONITOR

OUT

SURROUND

SURROUND BACK

SPEAKERS

CENTER

SUB WOOFER

SURR BACK

Best

Standard

SURROUND

SPEAKERS

PRE OUT

SUB WOOFER

FRONT

SPEAKERS A

SPEAKERS B

FRONT

R S VIDEO

AUDIO

OUT

VIDEO

OUT

OPTICAL

OUT

YCOAXIAL

COMPONENT VIDEO OUT

Connect one or the other Connection must be assigned (see page 33)

DVD player

To connect a DVD player or DVD-Audio/SACD-capable player with a multichannel analog audio output, see page 24.

Connecting Your Components

—Continued

Hooking Up the Multichannel DVD Input

If your DVD player supports multichannel audio formats such as DVD-Audio or SACD, and it has a multichannel analog audio output, you can connect it to the AV receiver’s multichannel DVD input.

Use a multichannel analog audio cable, or several normal audio cables, to connect the AV receiver’s DVD IN FRONT L/R, CENTER, SURROUND L/R, SURR BACK L/R, and SUBWOOFER jacks to the 7.1-channel analog audio output on your DVD player. If your DVD player has a 5.1-channel analog audio output, don’t connect anything to the AV receiver’s SURR BACK L/R jacks.

DIGITAL IN

COA XIAL

OPTICAL

REMOTE CONTROL

VIDEO 2 IN

COMPONENT

VIDEO 1 IN DVD IN

IN IN

CD TAPE

OUT

VIDEO

ANTENNA

OUT

VIDEO 2 VIDEO 1

VIDEO 2 VIDEO 1 DVD

FMAM75

IN IN IN

OUT

IN IN

OUT

DVD

FRONT

MONITOR

OUT

SURROUND

SURROUND BACK

SPEAKERS

CENTER

SUB WOOFER

SURR BACK

SURROUND SPEAKERS

FRONT

SPEAKERS A

SUB WOOFER

FRONT

SPEAKERS B

PRE OUT

LLR

SURROUND

5.1 ch

FRONT

SURROUND

DVD

CENTER SUB

CENTER

SPEAKER

7.1 ch

SUB WOOFER

CENTER

WOOFER

SURR BACK

DVD player

+ 56 hidden pages