Onkyo TX-SR505E, TX SR575, TX-SR505 User Manual
QUICK SETUP
Speaker Set A Hookup
Model : TX-SR505/TX-SR505E/TX-SR575
Thank you for purchasing this product.
This quick setup sheet shows the typical hookup method for connecting
speakers and AV components (DVD player, TV, cable/satellite receiver).
For more detailed hookup information and operating instructions,
please see the Instruction Manual.
First of all,
turn on speaker set A.
Press the SPEAKERS [A] button on
the front panel. Make sure that speaker
indicator A is shown on the display.
BA
5/8''
(15mm)
Front right
speaker
Front left
speaker
Center
speaker
Turn off speaker set B when not in use.
Indicator should be off.
Speaker Set A Layout (Main Room)
Front
Front
Left
Sub
woofer
Sub
woofer
Surround
Surround
Left
Left
Left
TV
TV
Listener
Listener
Center
Center
Front
Front
Right
Right
Surround
Surround
Right
Right
Powered
subwoofer
Surround right
speaker
Surround back
right speaker
Surround back
left speaker
Surround
left speaker
Surround
Surround
Back
Back
Left
Left
Surround
Surround
Back
Back
Right
Right
See the other side of this sheet for the AV component hookup.
SN 29344423(C) Copyright 2007 ONKYO CORPORATION Japan. All rights reserved.
AV Component Hookup
See the other side of this sheet for the Speaker hookup.See the other side of this sheet for the Speaker hookup.
If you have an HDMI-compatible TV and players, you can connect them
to the AV receiver with HDMI cables. The audio and video signals received
via the HDMI inputs are output by the HDMI OUT as they are (pass-through).
To listen through the speakers connected to the AV receiver, please make
the audio connections shown below.
HDMI
IN
Sound off
To fully enjoy the AV receiver's
listening modes, turn off the
volume on your TV.
TV
IF NO HDMI
DIGITAL
OUT
COAXIAL
AUDIO
OUT
L
R
If your TV or player doesn't support HDMI, use the analog or digital
connections shown below.
VIDEO
OUT
DVD player
VIDEO 1
IN
Please ensure the monitor input
(VIDEO 1, VIDEO 2, VIDEO 3, etc.)
selected corresponds to actual
connection used.
TV
HDMI
OUT
COAXIAL
L
R
OUT
Cable/
satellite
Antenna input
(e.g..RF IN)
HDMI
OUT
DIGITAL
OUT
COAXIAL
AUDIO
Assigning the HDMI Input
If you connect a video component to an HDMI input,
you must assign that HDMI Input to an input selector in Setup.
If you make the same connections as shown here, you must
assign the "HDMI DVD" setting to "IN1", and assign the
"HDMI CBL" setting to "IN2".
L
OUT
R
AUDIO
OUT
DVD player
DIGITAL
Coaxial feed from TV antenna
If you are not using Cable/satellite
box, please refer to the instruction
manual.
On the front panel On the front panel
TUNING
PRESET
ENTER
SETUP
L
R
COAXIAL
DIGITAL
OUT
VIDEO
OUT
AUDIO
OUT
Cable/
satellite
Antenna input
(e.g..RF IN)
Assigning the Digital Input
If there's no sound, press the [DIGITAL INPUT]
button repeatedly until sound is heard. The digital input is
now properly assigned.
If you connect your DVD player to the AV receiver's
COAXIAL 1 DIGITAL IN, and your cable/satellite receiver
to the COAXIAL 2 DIGITAL IN, as shown, it's not necessary
to assign the digital input.
Coaxial feed from
TV antenna
If you are not using
Cable/satellite box,
please refer to the
instruction manual.
DIGITAL INPUT
Loading...