COMPONENTS IDENTIFIED BY MARK ON THE
SCHEMATIC DIAGRAM AND IN THE PARTS LIST ARE
CRITICAL FOR RISK OF FIRE AND ELECTRIC SHOCK.
REPLACE THESE COMPONENTS WITH ONKYO
PARTS WHOSE PART NUMBERS APPEAR AS SHOWN
IN THIS MANUAL.
MAKE LEAKAGE-CURRENT OR RESISTANCE
MEASUREMENTS TO DETERMINE THAT EXPOSED
PARTS ARE ACCEPTABLY INSULATED FROM THE
SUPPLY CIRCUIT BEFORE RETURNING THE
APPLIANCE TO THE CUSTOMER.
SPECIFICATIONS
2
TX-SR500/E
AMPLIFIER SECTION
Continuous Average Power output (FTC)
All channels:
Continuous Power output (DIN)85 watts 5 at 6 ohms
Maximum Power output (EIAJ) 115 watts 5 at 6 ohms
Dynamic power output:160 watts 2 at 3 ohms
Total Harmonic Distortion:0.08% at rated power
IM Distortion:0.08% at rated power
Damping Factor:60 at 8 ohms
Input Sensitivity and Impedance
DIGITAL INPUT (OPTICAL 1, 2):
DIGITAL INPUT (COAXIAL):
LINE (CD, VIDEO 1, 2, 3, TAPE):
Multichannel Input
(DVD FRONT L/C/R, SURR L/R):
(SUBWOOFER):36 mV, 50 kohms
Output Level and Impedance
Rec out (TAPE, VIDEO 1): 200 mV, 470 ohms
Pre out (SUBWOOFER): 1 V, 470 ohms
Frequency Response:
Tone Control
Bass:±12 dB at 50 Hz
Treble:±12 dB at 20 kHz
Signal-to-Noise Ratio:
Muting:-50 dB
65 watts per channel min. RMS at 8 ohms,
2 channels driven from 20 Hz to 20 kHz
with no more than 0.08% total harmonic
distortion.
125 watts 2 at 4 ohms
85 watts 2 at 8 ohms
0.08% at 1 watt output
0.08% at 1 watt output
0.5 Vp-p, 75 ohms
0.5 Vp-p, 75 ohms
200 mV, 50 kohms
200 mV, 50 kohms
10 Hz to 10 kHz, +1/ -3 dB (Direct mode)
CD/TAPE: 100 dB (IHF-A, Direct mode)
VIDEO SECTION
Input Sensitivity and Impedance
VIDEO (DVD, VIDEO 1, 2, 3):
S VIDEO (DVD, VIDEO 1, 2, 3):
Output Level and Impedance
VIDEO (VIDEO 1, 2, MONITOR):
S VIDEO (VIDEO 1, 2, MONITOR):
1 Vp-p, 75 ohms
1 Vp-p, 75 ohms (Y)
0.28 Vp-p, 75 ohms (C)
1 Vp-p, 75 ohms
1 Vp-p, 75 ohms (Y)
0.28 Vp-p, 75 ohms (C)
TUNER SECTION
FM
Tuning Range:87.5-108.0 MHz (50 kHz steps)
Usable Sensitivity
Mono:11.2 dBf, 1.0 µV (75 ohms, IHF)
Stereo:17.2 dBf, 2.0 µV (75 ohms, IHF)
11.2 dBf, 0.9 µV (75 ohms, DIN)
17.2 dBf, 23 µV (75 ohms DIN)
50 dB Quieting Sensitivity
Mono:17.2 dBf, 2.0 µV (75 ohms)
Stereo:37.2 dBf, 20.0 µV (75 ohms)
Capture Ratio:2.0 dB
Image Rejection Ratio
North American models:40 dB
Other models:85 dB
IF Rejection Ratio:90 dB
Signal-to-Noise Ratio
Mono:76 dB, IHF
Stereo:70 dB, IHF
Alternate Channel Attenuation: 55 dB, IHF, ±400 kHz
Selectivity:50 dB (DIN)
AM Suppression Ratio:50 dB
Total Harmonic Distortion
Mono:0.2%
Stereo:0.3%
Frequency Response:30 Hz-15 kHz, ±1.0 dB
Stereo Separation:45 dB at 1 kHz
AM
Tuning Range
North American models:530-1,710 kHz (10 kHz steps)
European & Australian models:
Worldwide models:531-1,602 kHz (9 kHz steps),
Usable Sensitivity:30 µV
Image Rejection Ratio:40 dB
IF Rejection Ratio:40 dB
Signal-to-Noise Ratio:40 dB
Total Harmonic Distortion:0.7%
Dimensions (W H D):17-1/8" 5-7/8" 14-13/16"
Weight
North American models:18.7 lbs., 8.5 kg
Other models:19.4 lbs., 8.8 kg
AC 120 V, 60 Hz4.0 A
AC 230-240 V, 50 Hz 320 W
AC 220-230 V and 120 V
switchable,
435 150 376 mm
50/60 Hz 320 W
REMOTE CONTROL
Transmitter:Infrared
Signal range:Approx. 16 ft., 5 meters
Power supply:Two "AA" batteries (1.5 V 2)
Specifications and features are subject to change without notice.
Power supply and voltage vary depending on the area in which
the unit is
purchased.
SERVICE PROCEDURES
3
1. Replacing the fuses
TX-SR500/E
This symbol located near the fuses indicates that the
fuse used is fast operating type. For continued protection against
fire hazard, replace with same type fuse. For fuse rating refer to
the marking adjacent to the symbol.
Ce symbole indique que le fusible utlise est a rapide.
Pour une protection permanente, n'untiliser que fusibles de
meme type. Ce darnier est la qu le present symbol est
appse.
CIRCUIT NO. PART NO. DESCRIPTION
F6901,252198 or8A-UL or
F69022522618A-T/UL-ST2,Fuse <D>
2520998A-EAK,Fuse <O>
F901 252166 or6.3A-UL/T-237 or
2522606.3A-T/UL-ST2,Fuse <D/T/A/R/Q>
F902 252076 or3.15A-SE-EAK or
2522423.15A-SE-TL250V,Fuse <O>
F903 252075 or2.5A-SE-EAK or
252241
2.5A-SE-TL250V,Fuse <O>
Note: <D>:120V model only
<O>: Other models except 120V model
<T>: Asian model only for 230V
<R>: Chinese model only
<Q>: Hongkong model only
<A>: Australian model only
2. To initialize the unit
This device employs a microprocessor to perform various
functions and operations. If interference generated by an external
power supply, radio wave, or other electrical source results in
accident which causes the specified operations and functions to
operate abnormally.
To perform a result, please follow the procedure below.
1.Press and hold down the VIDEO-1 button, then press the
STANDBY/ON button.
2.After "clear" is displayed, the preset memory and each
mode stored in the memory, such as surround, are
initialized and will return to the factory setting.
5.Setting the voltage selector (Worldwide models
only)
Worldwide models are equipped with a voltage selector to conform
with local power supplies. Be sure to set this switch to match the
voltage of the power supply in your area before plugging in the unit.
Determine the proper voltage for your area: 220-230 V or 120 V. If
the preset voltage is not correct for your area, insert a screwdriver
into the groove in the switch. Slide the switch all the way to the
upper (120 V) or to the lower (220-230 V), whichever is appropriate.
FM
AM
ANTENNA
SUBWOOFER
PRE OUT
DIGITAL INPUT
OPTICAL
IN
CD
75
VIDEO 1
VIDEO 2
DVD MONITOR
IN
IN
IN
OUT
REMOTE
COAXIAL
CONTROL
12
OUT
IN
IN
IN
OUT
TAPE
FRONT
L
R
VIDEO 1
VIDEO 2
FRONT
SPEAKERS A
L
OUT
VIDEO
R
S VIDEO
SURR
CENTER
L
R
SUB
WOOFER
DVD
L
R
FRONT
SPEAKERS B
SURROUND
SPEAKERS
L
R
VOLTAGE
SELECTOR
220-230 V
CENTER
SPEAKER
120 V
AC OUTLET
VOLTAGE
SELECTOR
120 V
220-230 V
6.Setting the AM tuning step frequency
(Worldwide models only)
You can switch the AM band tuning steps between 9 kHz and
10 kHz.
The initial setting is 9 kHz. Please set the AM tuning step frequency
to match the AM band tuning step frequency in your area.
USA and Canadian models10 kHz
Other models9 kHz
Press MEMORY while holding down
TUNER.
3. Safety-check out
(Only U.S.A. model)
After correcting the original service problem, perform the
Note
All the preset stations are erased when you switch the AM band
tuning steps.
following safety check before releasing the set to the customer.
Connect the insulating-resistance tester between the plug of power
supply cord and screw on the back panel.
Specifications: 3.3Mohm+/-10% at 500V.
4. Memory Preservation
This unit does not require memory preservation batteries. A
built-in memory po wer back-up system preserves the contents
of the memory during power failures and even when the unit is
unplugged. The unit must be plugged in order to charge the
back-up system.
The memory preservation period after the unit has been
unplugged varies depending on climate and placement of the
unit. On the average, memory contents are protected over a
period of a few weeks after the last time the unit has been
unplugged. This period is shorter when the unit is exposed to a
highly humid climate.
EXPLODED VIEW
4
P901
33
33
11
Chinese
model only
32
31
U12
U13
U24
TX-SR500/E
54
U31
U1
P101
U7
54
U9
U23
2
U22
2
17
17
33
U20
U19
T901
F903
F901
F902
U21
2
21
22
23
12
Q6050
F6901
F6902
9
9
U17
U11
56
8
13
2
Q6064
5
7
55
2
8
U18
2
U10
10
*
U4
6
21
22
23
2
3
U5
4 & U18:Except 120V model
*
P7001
P7503
*
4
17
U3
U6
25
52
2
53
16
1
2
51
24
53
TX-SR500/E
TX-SR500/E
5
EXPLODED VIEW-PARTS LIST
REF.NO. PART NO.DESCRIPTION
127111268Front bracket <B>
27111269Front bracket <S>
27111270Front bracket <G>
28381300883TTB+8B,Self-tapping screw
3821430103P+10FN(BC),Pan head screw
428325497AKnob,power <B>
28325499AKnob, power <G>
28325547AKnob, power <S>
527100416Chassis
627190503AKGLS-8RF,Holder
727190813KGPS-10RF,Holder
827190428AKGLS-10RF,Holder
98304400894TTC+8C(BC),Self-tapping screw
U11A928501-1ANADG-7401-1A,DSP circuit PC board ass'y <D>
1A928501-1BNADG-7401-1B,DSP circuit PC board ass'y <P>
1A928501-1CNADG-7401-1C,DSP circuit PC board ass'y <A/K>
1A928501-1DNADG-7401-1D,DSP circuit PC board ass'y <T/R/Q>
U31A928503-1ANADIS-7403-1A,Display circuit PC board ass'y <D>
1A928503-1BNADIS-7403-1B,Display circuit PC board ass'y <O>
U41A928504-1ANASW-7404-1A,Standby switch PC board ass'y <D>
1A928504-1BNASW-7404-1B,Standby switch PC board ass'y <O>
U51A928505-1ANAETC-7405-1A,Headphone terminal PC board ass'y <D>
1A928505-1BNAETC-7405-1B,Headphone terminal PC board ass'y <O>
U61A928506-1ANAETC-7406-1A,Front video PC board ass'y <D>
1A928506-1BNAETC-7406-1B,Front video PC board ass'y <O>
U71A928507-1ANAETC-7407-1A,Connector PC board ass'y <D>
1A928507-1BNAETC-7407-1B,Connector PC board ass'y <O>
U91A928509-1ANAAF-7409-1A, Power amplifier driver PC board ass'y <D>
1A928509-1BNAAF-7409-1B, Power amplifier driver PC board ass'y <O>
U101A928510-1ANAETC-7410-1A,Regulator PC board ass'y <D>
1A928510-1BNAETC-7410-1B,Regulator PC board ass'y <O>
U111A928511-1ANAETC-7411-1A,Secondary circuit PC board ass'y <D>
1A928511-1BNAETC-7411-1B,Secondary circuit PC board ass'y <O>
U121A928512-1ANAETC-7412-1A,Speaker terminal PC board ass'y <D>
1A928512-1BNAETC-7412-1B,Speaker terminal PC board ass'y <O>
U131A928513-1ANAETC-7413-1A,PC board for holder <D>
1A928513-1BNAETC-7413-1B,PC board for holder <O>
U171A928517-1ANAAF-7417-1A,Power amplifier PC board ass'y <D>
1A928517-1BNAAF-7417-1B,Power amplifier PC board ass'y <P>
1A928517-1CNAAF-7417-1C,Power amplifier PC board ass'y <A>
1A928517-1DNAAF-7417-1D,Power amplifier PC board ass'y <R>
1A928517-1ENAAF-7417-1E,Power amplifier PC board ass'y <T/Q>
1A928517-1FNAAF-7417-1F,Power amplifier PC board ass'y <K>
U181A928518-1BNASW-7418-1B,Power switch PC board ass'y <P>
1A928518-1CNASW-7418-1C,Power switc h PC board ass'y <A>
1A928518-1DNASW-7418-1D,Power switc h PC board ass'y <R>
1A928518-1ENASW-7418-1E,Power switch PC board ass'y <T/Q>
1A928518-1FNASW-7418-1F,Power switch PC board ass'y <K>
!
!
!
REF.NO. PART NO.DESCRIPTION
U191A928519-1ANAPS-7419-1A,Terminal PC board ass'y <D>
1A928519-1BNAPS-7419-1B,Terminal PC board ass'y <P>
1A928519-1CNAPS-7419-1C,Terminal PC board ass'y <A>
1A928519-1DNAPS-7419-1D,Terminal PC board ass'y <R>
1A928519-1ENAPS-7419-1E,Terminal PC board ass'y <T/Q>
1A928519-1FNAPS-7419-1F,Terminal PC board ass'y <K>
U201A928520-1ANAPS-7420-1A,Primary circuit PC board ass'y <D>
1A928520-1BNAPS-7420-1B,Primary circuit PC board ass'y <P>
1A928520-1CNAPS-7420-1C,Primary circuit PC board ass'y <A>
1A928520-1DNAPS-7420-1D,Primary circuit PC board ass'y <R>
1A928520-1ENAPS-7420-1E,Primary circuit PC board ass'y <T/Q>
1A928520-1FNAPS-7420-1F,Primary circuit PC board ass'y <K>
U211A928521-1ANAPS-7421-1A,Terminal PC board ass'y <D>
1A928521-1BNAPS-7421-1B,Terminal PC board ass'y <P>
1A928521-1CNAPS-7421-1C,Terminal PC board ass'y <A>
1A928521-1DNAPS-7421-1D,Terminal PC board ass'y <R>
1A928521-1ENAPS-7421-1E,Terminal PC board ass'y <T/Q>
1A928521-1FNAPS-7421-1F,Terminal PC board ass'y <K>
U221A928522-1ANAVD-7422-1A,Video terminal PC board ass'y <D>
1A928522-1BNAVD-7422-1B,Video terminal PC board ass'y <P>
1A928522-1CNAVD-7422-1C,Video terminal PC board ass'y <A>
1A928522-1DNAVD-7422-1D,Video terminal PC board ass'y <R>
1A928522-1ENAVD-7422-1E,Video terminal PC board ass'y <T/Q>
1A928522-1FNAVD-7422-1F,Video terminal PC board ass'y <K>
U231A928523-1ANAETC-7423-1A,PC board for holder <D>
1A928523-1BNAETC-7423-1B,PC board for holder <P>
1A928523-1CNAETC-7423-1C,PC board for holder <A>
1A928523-1DNAETC-7423-1D,PC board for holder <R>
1A928523-1ENAETC-7423-1E,PC board for holder <T/Q>
1A928523-1FNAETC-7423-1F,PC board for holder <K>
U241A928524-1ANAETC-7424-1A,Thermal detector circuit PC board ass'y <D>
1A928524-1BNAETC-7424-1B,Thermal detector circuit PC board ass'y <P>
1A928524-1CNAETC-7424-1C,Thermal detector circuit PC board ass'y <A>
1A928524-1DNAETC-7424-1D,Thermal detector circuit PC board ass'y <R>
1A928524-1ENAETC-7424-1E,Thermal detector circuit PC board ass'y <T/Q>
1A928524-1FNAETC-7424-1F,Thermal detector circuit PC board ass'y <K>
U251A928525-1FNAETC-7425-1F,PC board ass'y <K>
U31240134ATFCE1U114B,Tuner unit <D>
240135,TFCE1E512A,
240138A orENG06501QR or
240139A ENG07501QR,Tuner unit <O>
NOTE: THE COMPONENTS IDENTIFIED BY MARK !
ARE CRITICAL FOR RISK OF FIRE AND
ELECTRIC SHOCK. REPLACE ONLY WITH
PART NUMBER SPECIFIED.
Note:
<B>: Black model only
<G>: Golden model only
<S>: Silver model only
<D>: 120V model only
<P>: European model only
<T>: Worldwide model only
<K>: Korean model only
<A>: Australian model only
<R>: Chinese model only
<C>: Canadian model only
<Q>: Hongkong model only
<O>: Except 120V model