COMPONENTS IDENTIFIED BY MARK ON THE
SCHEMATIC DIAGRAM AND IN THE PARTS LIST ARE
CRITICAL FOR RISK OF FIRE AND ELECTRIC SHOCK.
REPLACE THESE COMPONENTS WITH ONKYO
PARTS WHOSE PART NUMBERS APPEAR AS SHOWN
IN THIS MANUAL.
MAKE LEAKAGE-CURRENT OR RESISTANCE
MEASUREMENTS TO DETERMINE THAT EXPOSED
PARTS ARE ACCEPTABLY INSULATED FROM THE
SUPPLY CIRCUIT BEFORE RETURNING THE
APPLIANCE TO THE CUSTOMER.
RC-479S
SPECIFICATION
Amplifier SectionGeneral
Power Output
Front L/R: 65 W + 65 W
Center: 65 W
Surround L/R: 65 W + 65 W
(8 , 20 Hz~20 kHz, FTC)
Dynamic Power: 160 W + 160 W (3 , Front)
125 W + 125 W ( 4 , Front)
85 W + 85 W (8 , Front)
THD
(Total Harmonic Distortion): 0.08 % (Power Rated)
Damping Factor: 60 (Front, 1 kHz, 8 )
Input Sensitivity and Impedance:
Output Level and Impedance: 200 mV/ 470 (REC OUT)
Frequency Response: 10 Hz~100 kHz/ +1 dB, -3 dB (Direct
mode)
Tone Control: +12 dB, -12 dB, 50 Hz (BASS)
+12 dB, -12 dB, 20 kHz (TREBLE)
SN Ratio: 100 dB (LINE, IHF-A)
Speaker Impedance: 8 ~16
200 mV/ 47 k (LINE)
Video Section
Input Sensitivity/Output Level and Impedance:
1 Vp-p /75 (Composite)
Power Supply: AC 120 V, 60 Hz
Power Consumption: 4.2 A
Stand-by Power Consumption: 1.6 W
Dimensions (W x H x D): 435 x 150 x 365 x mm
17 1/8 x 5 7/8 x 14 3/8 inches
Weight: 8.4 kg
18.5 lbs
Video Inputs
A/V Input: DVD, VIDEO 1, VIDEO 2, VIDEO 3
Video Outputs
A/V Output: MONITOR, VIDEO 1
Audio Inputs
Digital Inputs: 1 (Optical), 1 (Coaxial)
Analog Inputs: DVD (MULTICHANNEL), CD, TAPE,
VIDEO 1, VIDEO 2, VIDEO 3
Multichannel Inputs: 6
Audio Outputs
Analog Outputs: TAPE, VIDEO 1
Subwoofer Pre Outputs: 1
Speaker Outputs: 5 + 2
Phones: 1
TX-SR302
Tuner Section
FM
Tuning Frequency Range: 87.5 MHz~108.0 MHz
Usable Sensitivity: Stereo 17.2 dBf 2 V (75 IHF)
Mono 11.2 dBf 1 V (75 IHF)
S/N Ratio: Stereo 70 dB (IHF-A)
Mono 76 dB (IHF-A)
THD: Stereo 0.3 % (1 kHz)
Mono 0.2 % (1 kHz)
Frequency Response : 30 Hz~ 15 kHz / +1 dB, -1 dB
Stereo Separation: 45 dB (1 kHz )
AM
Tuning Frequency Range: 530 kHz~1710 kHz
Usable Sensitivity: 30 V
S/N Ratio: 40 dB
THD: 0.70 %
Specifications and features are subject to change without notice.
SERVICE PROCEDURES
TX-SR302
1. Replacing the fuses
This symbol located near the fuse indicates that the
fuse used is show operating type, For continued protection against
fire hazard, replace with same type fuse, For fuse rating, refer to
the marking adjacent to the symbol.
Ce symbole indique que le fusible utilise est e lent.
Pour une protection permanente, n'utiliser que des fusibles de meme
type. Ce demier est indique la qu le present symbol est apposre.
REF. NO.
F6901
F6901 or
F6902
F6902 or
F901
F901 or
F903
F903 or
After correcting the original service problem perform the
following safety check before releasing the set to the customer
Connect the insulating-resistance tester between the plug of
power supply cord and terminal GND on the back panel.
Specifications: More than 10Mohm at 500V
5. Memory Preservation
This unit does not require memory preservation batteries.
A built-in memory power backup system preserves the contents of
memory during power failures and even when the power cord is unplugged.
The power cord must be plugged in order to charge the backup system.
The memory preservation period after the unit has been turned off varies
depending on climate and placement of the unit. On average, memory
contents are protected over a period of a few weeks after the time the unit
has been turned off.
This period is shorter when the unit is exposed to a very humid climate.
3. To initialize the unit
This device employs a microprocessor to perform various
functions and operations. If interference generated by an external
power supply, radio wave, or other electrical sauce results in accident
which causes the specified operations and functions to operate
abnormally.
To perform a result, please follow the procedure below.
1. Press and the hold down the VIDEO 1 button , then press the
STANDBY/ON button when the unit is Power ON.
2. After " Clear " is displayed, the preset memory and each mode
stored in the memory, are initialized and will return to the
factory settings.
4. How to check version of microprocessor?
Main microprocessor Q7008
1. Press and the hold down the DISPLAY button , then press the
STANDBY/ON button when the unit is Power ON.
Version is displayed on FL display only for 3 seconds.
ex.
Version 04212a
2. Press the STANDBY/ON button to Power Off.
OPERATION CHECK-1
DC VOLTAGE DETECTION PROTECTORS
[NOTE1]
Limit time to apply voltage is 0.5 to 1.0 seconds each channel.
When protection operation does not occur at once, try several times.
[NOTE2]
Don't connect speakers or any load.
Don't short speaker terminals.
1. Set the unit to test mode " Test-1-00 " .
1-1. Press and the hold down the CD button , then press the STANDBY/ON button when the unit is Power ON.
1-2. Press the DVD button, while the " Test - _ " is shown.
Unit will be in the state of " Test-1-00 ".
2. Apply DC voltage (+1.5 to +3V) to MULTI CHANNEL (FL, FR, SL, SR, C) terminal, each channel.
3. Check that " Protect " is shown.
4. Apply DC voltage (-1.5 to -3V) to MULTI CHANNEL (FL, FR, SL, SR, C) terminal, each channel.
5. Check that " Protect " is shown.
6. Press the STANDBY/ON button.
FL display
Test - _
Test - 1-00
Clear
0.5 sec.
Disappears
TX-SR302
CURRENT DETECTION PROTECTORS
[NOTE]
In the state of test mode" Test-4-29 ", the pulse waveform output for checking from speaker terminal automatically.
Therefore, oscillator is unnecessary.
1. Set the unit to test mode " Test-4-29 "
1-1. Press and the hold down the CD button , then press the STANDBY/ON button when the unit is Power ON.
1-2. Press the VIDEO 3 button, while the" Test - _ " is shown.
Unit will be in the state of " Test-4-00 ".
1-3. Repeat and press SPEAKERS B button to the " Test-4-29 " is shown.
2. Connect the lord resister (3 ohms) to the speaker terminals.
3. Check that the" Protect " is not shown, and speaker relays not turn OFF.
4. Check the each speaker terminals.
5. Connect the lord resister (1.5 ohms) to the speaker terminals.
6. Check that the " Protect " is shown, and speaker relays turn OFF immediately.
7. Check the each speaker terminals.
8. Press the STANDBY/ON button.
FL display
Test - _
Test - 4-00
Test - 4-29
Disappears
Clear
OPERATION CHECK-2
OUTPUT LEVEL & THERMAL DETECTION
Regarding the power supply system of this unit.
<Function>
1. High-voltage mode
Usually, the power supply supplies high voltage to the power amplifier circuit when the relay (RL6901) is turned On.
2. Low-voltage mode
When as follows, a power supply changes to the state of supplying low voltage when the relay (RL6901) in turned Off.
(1) Excessive output signal is continuously outputted from power amplifier.
(2) Temperature of a heat sink over 80 degrees.
<Purpose>
1. The loss which power amplifier generates is decreased. As a result, the miniaturization of a heat sink is realized.
2. Corresponds to a safety standard.
TX-SR302
<Block diagram>
POWER AMP.
THERMAL
SENSOR
R6380
Q6303
THERMAL
DETECTION
SPEAKER
OUT
OUTPUT
LEVEL
DETECTION
VOLH/
THPRO
+B1
HIGH
VOLTAGE
MODE
LOW
VOLTAGE
MODE
-B1
Q7008
2
MAIN
MICROPROCESSOR
+/- 49 V
+/- 28.9 V
23
SEC1H
RL6901
D6903
RL6902
D6904
Q6303
F6901
F6902
High
Low
Low
High
<Necessity for a check of operation>
May not notice the fuse (F6901, F6902) broken in the case of repair.
Because the power supply is continuing supplying voltage from the High side of SEC1 at high-voltage mode.
When a power supply circuit changes to low voltage mode, amplifier does not operate.
Therefore, it is very important to check operation of this power supply system containing a fuse.
<Procedure>
[NOTE]
Don't connect speakers or any load.
Don't short speaker terminals.
(1) Set the unit is Multi channel input state.
(2) Set the master volume into the minimum.
(3) Apply sine wave signal to MULTI CHANNEL INPUT (FL+FR+C+SL) terminals.
(4) Connect an oscilloscope to speaker terminal of FL channel.
(5) Adjust master volume so that a speaker output may become distortion about 5%.
SEC1
PRI.
T901 MAIN
TRANSFORMER
High-voltage
(6) Check that the RL6901 and RL6902 are turned Off after about 5 seconds progress.
And the power supply changes to low-voltage mode.
Low-voltage
(7) Adjust the master volume so that output voltage may become half.
(8) Check that the RL6901 and RL6902 are turned On after 2 to 3 minutes.
And the power supply returns to high-voltage mode.
OPERATION CHECK-3
OUTPUT LEVEL & THERMAL DETECTION
<Check by test mode>
The following is the procedure of checking detection operation of a microprocessor in false, by using test mode.
OUTPUT LEVEL DETECTION
1. Set the unit to test mode " Test-3-2 "
1-1. Press and the hold down the CD button , then press the STANDBY/ON button when the unit is Power On.
TX-SR302
Test - _
1-2. Press the VIDEO 2 button, while the" Test - _ " is shown.
Unit will be in the state of " Test-3-00 ".
Test - 3-00
1-3. Repeat and press SPEAKERS B to while the " Test-3-2 " is shown.
Test - 3-02
2. Apply signal (sine wave 1kHz, -1.5dBV) to MULTI CHANNEL (FL, FR, SL, SR, C) terminal, each channel.
3. Check that FM STEREO indicator is shown.
FM STEREO
FM STEREO
Test - 3-02
4. Press the STANDBY/ON button.
0.5 sec.
Clear
THERMAL DETECTION
1. Set the unit to test mode " Test-3-2 "
Refer to the clause of "Output level detection".
2. Connect the resistor (2.7 kohms, 1W) between " HT1 " and " COM " terminals of P6301.
Disappears
2.7 kohms
1W
P6301
COM
3. Check that FM STEREO indicator is shown.
TH1
FM STEREO
Test - 3-02
4. Press the STANDBY/ON button.
0.5 sec.
Clear
30
TH1
COM
TH2
P6301
Front side
U16
NAAF-8245
POWER AMPLIFIER PC BOARD
FM STEREO
Disappears
OPERATION CHECK-4
DSP DEBUG MODE
<Regarding the DSP debug mode>
TIn this test mode, the check with normal communication of a microprocessor and the data of DSP and DIR is possible.
This information is a help to find the cause of failure.
<How to go in DSP debug mode>
1. Press and hold down the DISPLAY button, then press the STANDBY/ON button when the unit is power ON.
TX-SR302
FL display
<Ex.>
2. Press the DISPLAY button, while the" Version 04212a " is shown.
Version 04212a
1 sec.
DSP Debug Mode
<How to exit>
Press STANDBY/ON button.
<Explanation of each parameter>
Details of FL display
142568793
DIR
1
UNLOCK
E = UNLOCK
= LOCK
Digital Selector
2
D = DIGITAL
A = ANALOG
1 = COAX
2 = OPT1
3 = OPT2
4 = Others
DC VOLTAGE
DETECTION &
OVER CURRENT
DETECTION
Q6701~6703
VOLTAGE
LEVEL SENSOR
RL6600
RL6604
RL6601
RL6603
D6703
PHONES
L
FRONT
SPEAKERS-A
R
CENTER
SPEAKER
L
SURROUND
SPEAKERS
R
L
FRONT
SPEAKERS-B
R
-12VAF
+5V
MICROPROCESSOR
SUB
MICROPROCESSOR
VIDEO SECTION
PRE-AMPLIFIER
SECTION
SELDA
SELCL
DSP IC
SELMUT
POWER SUPPLY
+5.6V
NJM78M56A
-VP
Q9501
+12V
Q6405
78M12
-12VAF
Q6402
78M12
-12VAF
Q6403
79M12
+5VDSP
Q6931
Q4606
78M05
POWER
AMPLIFIER SECTION
+B1-B1
D6903
AMUT
RL6901
RL6902
FL TUBE
SEC1H/L
CONTROL
Q6901
RELAY
+B2
SEC1H
D921
-924
+B1L+B1H
D6904
D9502
-9504
D9509
-9512
FLAC
FLAC
R6380
THERMAL
SENSOR
SUB
TRANSFORMER
T902
SEC1
PRI.
SEC2
SEC3
T901
MAIN
TRANSFORMER
D6704
F901
VOLH/THPRO
POWER
RL901
P902
AC OUTLET
PRO
SPF
SPCS
SPB
HPDET
AC IN
120V 60Hz
A
BCDEFGH
SCHEMATIC DIAGRAMS-1
PRE-AMPLIFIER SECTION
CD
1
TAPE OUT
TAPE IN
VIDEO-3 IN
VIDEO-2 IN
2
VIDEO-1 OUT
VIDEO-1 IN
DVD
SURROUND R
SURROUND L
SUB WOOFER
CENTER
3
4
NOTE
THE COMPONENTS IDENTIFIED BY MARK ARE CRITICAL FOR SAFETY
REPLACE ONLY WITH PART NUMBER SPECIFIED.
VOLTAGE (MEASURED WITH VOLTMETER) IS DC VOLTAGE.(NO INPUT SIGNAL).
ALL PNP TRANSISTORS ARE EQUIVALENT TO 2SA1015-GR UNLESS OTHERWISE NOTED.
ALL NPN TRANSISTORS ARE EQUIVALENT TO 2SC1815-GR UNLESS OTHERWISE NOTED.
ALL DIODES ARE EQUIVALENT TO 1SS133 UNLESS OTHERWISE NOTED.
ELECTROLYTIC CAPACITORS ( ) ARE IN uF/WV.
ALL CAPACITORS ARE IN pF/50WV UNLESS OTHERWISE NOTED.
EX) 030- 3pF 330- 33pF 331- 330pF 333- 0.033uF
ALL RESISTORS ARE IN OHMS 1/4WATTS UNLESS OTHERWISE NOTED.
THE THICK LINES ON PC BOARD ARE THE PRINTING SIDE OF THE PARTS.
EX) PRINTING SIDE
CIRCUIT IS SUBJECT TO CHANGE FOR IMPROVEMENT.
THE COMPONENTS IDENTIFIED BY MARK ARE CRITICAL FOR SAFETY
REPLACE ONLY WITH PART NUMBER SPECIFIED.
VOLTAGE (MEASURED WITH VOLTMETER) IS DC VOLTAGE.(NO INPUT SIGNAL).
ALL PNP TRANSISTORS ARE EQUIVALENT TO 2SA1015-GR UNLESS OTHERWISE NOTED.
ALL NPN TRANSISTORS ARE EQUIVALENT TO 2SC1815-GR UNLESS OTHERWISE NOTED.
ALL DIODES ARE EQUIVALENT TO 1SS133 UNLESS OTHERWISE NOTED.
ELECTROLYTIC CAPACITORS ( ) ARE IN uF/WV.
ALL CAPACITORS ARE IN pF/50WV UNLESS OTHERWISE NOTED.
EX) 030- 3pF 330- 33pF 331- 330pF 333- 0.033uF
ALL RESISTORS ARE IN OHMS 1/4WATTS UNLESS OTHERWISE NOTED.
THE THICK LINES ON PC BOARD ARE THE PRINTING SIDE OF THE PARTS.
EX) PRINTING SIDE
CIRCUIT IS SUBJECT TO CHANGE FOR IMPROVEMENT.
<Note>
NC=No mount of parts.
HPDET
GND
HPL
HPE
HPR
JL7502B
E7501
NC
L7501 022M
NC
L7502 022M
NC
C7518
102J
L7503 022M
U04
C7519
102J
C7520
102J
HEADPHONE JACK
PC BOARD
!
P7501
PHONES
NAETC-7405
A
SCHEMATIC DIAGRAMS-3
DRIVER AMPLIFIER SECTION
NAAF-7866
BCDEFGH
1
U08
DRIVER
AMPLIFIER
PC BOARD
2
3
SL
R5003
1K
C5003
101K
R5043
D5003
MTZJ5.6B
SR
R5004
1K
C5004
101K
R5044
D5004
MTZJ5.6B
2.2K
2.2K
C5013
22/16
C5014
22/16
R5013
56K
R5103
100K
R5014
56K
R5104
100K
R5093
100K
-0.1V
R5023
330
-43.3V
C5023
10/50
R5094
100K
-0.1V
R5024
330
-43.3V
C5024
10/50
R5063
1.2K
R5064
1.2K
R5113
1K
C5033
NC
-0.7V
R5114
1K
C5034
NC
-0.7V
R5053
4.7K
Q5053
-44V
R5073
560
R5054
4.7K
Q5054
-44V
R5074
560
47.5V
C5073
0V
R5133
18K
C5113
10/100
R5134
18K
C5114
10/100
0V
NC
-47.5V
47.5V
C5074
NC
-47.5V
C5093
101J
R5173
120
C5094
101J
120
Q5013Q5003
C5103
10/100
C5043
100/16
R5083
3.3K
Q5014Q5004
C5104
10/100
C5044
100/16
R5084
3.3K
1.0V
C5083
040D
(1/4W)
1.0V
C5084
040D
R5174
(1/4W)
R5163
(1/4W)
120
48.1V
C5053
47/50
R5033
56K
-1V
Q5043
-48.1V
R5164
120(1/4W)
48.1V
Q5034
C5054
47/50
R5034
56K
-1V
Q5044
-48.1V
R5183
10
(1/4W)
R5184
10
(1/4W)
48.9V
NF
-B1
+B1
B+
B-
R5193
10
(1/4W)
-48.9V
48.9V
NF
-B1
+B1
B+
B-
R5194
10
(1/4W)
-48.9V
P6003A
TO NAAF-7875
P6004A
TO NAAF-7875
NOTE
THE COMPONENTS IDENTIFIED BY MARK ARE CRITICAL FOR SAFETY
REPLACE ONLY WITH PART NUMBER SPECIFIED.
VOLTAGE (MEASURED WITH VOLTMETER) IS DC VOLTAGE.(NO INPUT SIGNAL).
ALL PNP TRANSISTORS ARE EQUIVALENT TO 2SA1015-GR UNLESS OTHERWISE NOTED.
4
ALL NPN TRANSISTORS ARE EQUIVALENT TO 2SC1815-GR UNLESS OTHERWISE NOTED.
ALL DIODES ARE EQUIVALENT TO 1SS133 UNLESS OTHERWISE NOTED.
ELECTROLYTIC CAPACITORS ( ) ARE IN uF/WV.
ALL CAPACITORS ARE IN pF/50WV UNLESS OTHERWISE NOTED.
EX) 030- 3pF 330- 33pF 331- 330pF 333- 0.033uF
ALL RESISTORS ARE IN OHMS 1/4WATTS UNLESS OTHERWISE NOTED.
THE THICK LINES ON PC BOARD ARE THE PRINTING SIDE OF THE PARTS.
EX) PRINTING SIDE
CIRCUIT IS SUBJECT TO CHANGE FOR IMPROVEMENT.
!
<Note>
NC=No mount of parts.
Refer to following table about the parts displayed by mark " ".
REF. NO.DESCRIPTION
Q5000-04,Q5010-14 KTC3200-BL OR 2SC1775A-E,F OR 2SC1845-E
Q5030-34KTA1024-Y,O OR 2SA949-Y,O
Q5040-44KTC3206-Y,O OR 2SC2229-Y,O
Q5050-54
KTC3200-BL,GR OR 2SC1775A-E,F OR 2SC1845-E,F
5
TO NADG-7401
ECESLESRERE
L
TX-SR302TX-SR302
P306A
E
E
E
E
E
E
E
E
TO NAAF-7875
E
P6011A
L
R5000
1K
C5000
101K
R5040
D5000
MTZJ5.6B
R
R5001
1K
C5001
101K
R5041
D5001
MTZJ5.6B
2.2K
2.2K
C5010
22/16
R5100
C5011
22/16
R5010
56K
100K
R5011
56K
R5101
100K
R5090
100K
-0.1V
R5020
330
-43.3V
C5020
10/50
R5091
100K
-0.1V
R5021
330
-43.3V
C5021
10/50
R5060
1.2K
R5061
1.2K
R5110
1K
C5030
NC
-0.7V
R5111
1K
C5031
NC
-0.7V
R5050
4.7K
Q5050
-44V
R5070
560
R5051
4.7K
Q5051
-44V
R5071
560
R5160
1.0V
C5080
040D
R5170
(1/4W)
1.0V
C5081
040D
R5171
(1/4W)
120 (1/4W)
48.1V
Q5030Q5033
C5050
47/50
R5030
56K
-1V
Q5040
-48.1V
R5161
120(1/4W)
48.1V
Q5031
C5051
47/50
R5031
56K
-1V
Q5041
-48.1V
47.5V
C5070
0V
R5130
18K
C5110
10/100
0V
R5131
18K
C5111
10/100
NC
-47.5V
47.5V
C5071
NC
-47.5V
C5090
101J
120
C5091
101J
120
Q5010Q5000
C5100
10/100
C5040
100/16
R5080
3.3K
Q5011Q5001
C5101
10/100
C5041
100/16
R5081
3.3K
R5180
10
(1/4W)
R5181
10
(1/4W)
48.9V
NF
-B1
+B1
B+
B-
R5190
10
(1/4W)
-48.9V
48.9V
NF
-B1
+B1
B+
B-
R5191
10
(1/4W)
-48.9V
P6000A
TO NAAF-7875
P6001A
TO NAAF-7875
C
R5002
1K
C5002
101K
R5042
2.2K
D5002
MTZJ5.6B
C5012
22/16
R5012
56K
R5102
100K
R5092
100K
-0.1V
R5022
330
-43.3V
C5022
10/50
R5062
1.2K
R5112
1K
C5032
NC
-0.7V
R5052
4.7K
Q5052
-44V
R5072
560
R5162
120
47.5V
C5072
NC
-47.5V
120
C5092
101J
R5172
(1/4W)
1.0V
C5082
040D
Q5012Q5002
C5102
R5082
3.3K
10/100
C5042
100/16
0V
R5132
18K
C5112
10/100
61.5V
Q5032
C5052
47/50
R5032
56K
-1V
Q5042
-48.1V
(1/4W)
R5182
10
(1/4W)
NF
-B1
+B1
B+
B-
R5192
10
(1/4W)
-48.9V
48.9V
P6002A
TO NAAF-7875
TX-SR302TX-SR302
A
SCHEMATIC DIAGRAMS-4
POWER AMPLIFIER SECTION
NAAF-7875
1
2
3
4
SL
-B1
+B1
TO NAAF-7866
SR
-B1-B1
+B1+B1
TO NAAF-7866
BCDEFGH
U17
POWER AMPLIFIER PC BOARD
R6033
390
R6003
5.6K
P6003
R6013
3.9K
NF
B+
B-
R6043
1K
R6053
3.9K
R6034
390
R6004
5.6K
P6004
R6014
3.9K
NFNF
B+B+
B-B-
R6044
1K
R6054
3.9K
1.1V
1V
0.2V
Q6013
-0.3V
R6023
NC
-48.9V
1V
Q6014
-0.3V
NC
-48.9V
Q6023
1.1V
Q6024
-1.1V
IID
-0.3V
0.2V
R6024
IID
-0.3V
<Note>
NC=No mount of parts.
Refer to following table about the parts displayed by mark " ".
REF. NO.DESCRIPTION
Q6010-60142SC1740S-R, S
Q6020-60242SC1740S-R, S
Q6030-60312SC5171
Q6040-60412SA1930
Q6032-60342SC5171
Q6042-60442SA1930
Q6050-60512SC5242-R, O OR MN150S-Y, P, O
Q6052-6054MN130S-Y, P, O OR 2SC5242-O, R
Q6060-60612SA1962-R, O OR MP150S-Y, P, O
Q6062-6064MP130S-Y, P, O OR 2SA1962-O, R
Q6070-60742SC2631-R, S
Q6601-6603,Q6901 KTC3199-GR, 2SC1740S-R, S, 2SC2458-GR
Q6701,6702KTC3200-BL, GR OR 2SC1775A-E, F OR 2SC1845-E, F
Q6703KTA1268-GR, BL OR 2SA992-E, F
Q6303
Q6033
-1.1V
0.5V
R6073
100
(1/4W)
-0.5V
Q6043
R6074
100
(1/4W)
-0.5V
Q6044
0.5V
P6083
ID+
ID-
C6043
47/50
R6133
NC
C6033
NC
Q6034
P6084
ID+
ID-
C6044
47/50
R6134
NC
C6034
NC
KTA1267-GR OR 2SA933S-R, S
R6083
2.2
(1/4W)
R6093
2.2
(1/4W)
R6084
2.2
(1/4W)
R6094
2.2
(1/4W)
0.5V
-0.5V
C6233
473J
R6233
8.2
0.5V
-0.5V
C6234
473J
R6234
8.2 (1W)
0V
R6103
0.22 x 2
(2W)
(1W)
0V
R6104
0.22 x 2
(2W)
48.9V
Q6053
R6143
22K
R6153
0V
Q6063
R6173
48.9V
Q6054
R6144
22K
0V
Q6064
R6174
12K
D6003
R6154
12K
D6004
47K
47K
R6163
33K
Q6073
R6164
33K
Q6074
R6193
330K
D6013
R6183
47K
R6194
330K
D6014
R6184
47K
E-B1
E+B1
EB+
EB-
E
E
E
E
E
P6011
D6904
RBV602
D5SBA20
RS603M
D6903
C6907
104J
C6905
334J/100
C6904
334J/100
C6906
104J
F6901
8A-UL,
8A-T/UL-ST2
RL6902
RL6901
JL6951A
TO NAPS-7878
D6906
TO NAPS-7878
F6902
8A-UL, 8A-T/UL-ST2
C6920
NC
0.1V
0.8V
Q6901
JL6952A
R6902
1K
NOTE
THE COMPONENTS IDENTIFIED BY MARK ARE CRITICAL FOR SAFETY
REPLACE ONLY WITH PART NUMBER SPECIFIED.
VOLTAGE (MEASURED WITH VOLTMETER) IS DC VOLTAGE.(NO INPUT SIGNAL).
ALL PNP TRANSISTORS ARE EQUIVALENT TO 2SA1015-GR UNLESS OTHERWISE NOTED.
ALL NPN TRANSISTORS ARE EQUIVALENT TO 2SC1815-GR UNLESS OTHERWISE NOTED.
ALL DIODES ARE EQUIVALENT TO 1SS133 UNLESS OTHERWISE NOTED.
ELECTROLYTIC CAPACITORS ( ) ARE IN uF/WV.
ALL CAPACITORS ARE IN pF/50WV UNLESS OTHERWISE NOTED.
EX) 030- 3pF 330- 33pF 331- 330pF 333- 0.033uF
ALL RESISTORS ARE IN OHMS 1/4WATTS UNLESS OTHERWISE NOTED.
THE THICK LINES ON PC BOARD ARE THE PRINTING SIDE OF THE PARTS.
EX) PRINTING SIDE
CIRCUIT IS SUBJECT TO CHANGE FOR IMPROVEMENT.
!
D6903, 6904:
C6901
8200/56
C6902
8200/56
NC
NC
C6903
104J
D6901
D6902
P6906
5
P931
+13VSSPF
+13VS+13VSPRO
MPUGNDPOWER
MPUGND+13VS
POWERPOWER
D6706
D6705
C6708
223Z
NC
NC
TO NAPS-7877
TO NAAF-7866
P6011
L
R6030
390
R6000
5.6K
P6000
R6010
3.9K
NF
R6040
1K
TO NAAF-7866
R6050
3.9K
R
R6031
390
R6001
5.6K
P6001
R6011
3.9K
R6041
TO NAAF-7866
1K
R6051
3.9K
C
R6032
390
R6002
5.6K
P6002
R6012
3.9K
NF
-B1
+B1
B+
B-
R6042
TO NAAF-7866
1K
R6052
3.9K
R6020
IID
0.2V
R6021
IID
0.2V
R6022
IID
0.2V
-0.3V
-0.3V
-0.3V
1V
Q6010
-48.9V
1V
Q6011
NC
1V
Q6012
-0.3V
NC
-0.3V
-48.9V
-0.3V
NC
-48.9V
1.1V
1.1V
1.1V
Q6020
-1.1V
Q6021
-1.1V
Q6022
-1.1V
R6070
100
(1/4W)
-0.5V
Q6040
R6071
100
(1/4W)
Q6041
R6072
100
(1/4W)
-0.5V
Q6042
0.5V
0.5V
-0.5V
0.5V
Q6030
C6040
47/50
Q6031
C6041
47/50
Q6032
C6042
47/50
R6130
NC
C6030
NC
R6131
NC
C6031
NC
R6132
NC
C6032
NC
R6080
2.2
(1/4W)
P6080
ID+
ID-
P6081
ID+
ID-
P6082
ID+
ID-
R6090
2.2
(1/4W)
R6081
2.2
(1/4W)
R6091
2.2
(1/4W)
R6082
2.2
(1/4W)
R6092
2.2
(1/4W)
-0.5V
C6230
473J
R6230
8.2
C6231
473J
R6231
8.2
C6232
473J
R6232
8.2
0.5V
0V
R6100
0.22 x 2
(1W)
0.5V
0V
R6101
0.22 x 2
-0.5V
(1W)
0.5V
R6102
0.22 x 2
-0.5V
(1W)
(2W)
(2W)
0V
(2W)
48.9V
Q6050
R6140
22K
0V
Q6060
48.9V
Q6051
R6141
22K
0V
Q6061
R6171
48.9V
Q6052
R6142
22K
0V
Q6062
R6150
12K
R6170
47K
D6000
D6001
R6152
12K
R6172
47K
D6002
R6151
12K
47K
R6160
33K
Q6070
R6161
33K
Q6071
R6162
33K
Q6072
R6190
330K
D6010
R6180
47K
R6191
330K
D6011
R6181
47K
R6192
330K
D6012
R6182
47K
R6306
NAETC-8256
TH1
COM
P6301
D6307
D6306
R6307
2.2K
10K
+24V
JL6402A
TH1
24V
Q6303
0V
R6308
4.7K
LSPE
RSPE
CSPE
LSSPE
RSSPE
JL6402B
THERMAL SENSOR
R6380
PTFL04BE471Q
2N34B0(90)
JL6804A
TO NAETC-7870
JL6803A
LSP
RSP
CSP
LSSP
RSSP
R6851
390
(1/2W)
R6850
(1/2W)
390
TO NAETC-7870
U26
THERMAL
SENSOR
PC BOARD
D6701
C6701
220/6.3
0V
R6702
10K
R6701
22K
R6708
33K
Q6701 Q6702
C6703
223Z
48.9V
50V
D6702
C6704
1/50
+B1
48.9V
Q6703
0V
R6704
47K
D6703
MTZJ5.1BD6704
C6706
100/6.3
R6706
220K
MTZJ5.1B
5.6K
R6709
R6710
12K
0.05V
R6601
24V
24V
Q6602Q6603Q6601
0.8V
R6603
1K
1K
R6602
0V0V
1K
VOLH/THPRO
BRLD
FRLD
CSRLD
+24V
HPL
HPR
+24V
MPUGND
SEC1H
SPB
SPCS
JL6805A
TO NAETC-7870
P6931
E
TO NAETC-7868
RLGND
TX-SR302TX-SR302
A
BCDEFGH
SCHEMATIC DIAGRAM-5
SPEAKER TERMINAL & POWER SUPPLY SECTION
NAETC-7870
1
2
U12
SPEAKER TERMINAL
PC BOARD
JL6803B
LSP
RSP
CSP
LSSP
RSSP
TO NAAF-7875
D6600
D6601
C6601
D6604
C6600
C6604
RL6600
RL6601
RL6603
RL6604
103J
103Z
103J
FRONT SPEAKERS-B
P6800
L
R
L
R
FRONT SPEAKERS-A
CENTER
SPEAKER
P6802
L
R
NAPS-7877
R92482
(1/2W)
D925
0.1V
C901
103M
/275VAC
F903
5A/125V
P902
SURROUND
SPEAKERS
R926
4.7K
R923
Q921
2SC2458-GR
KTC3199-GR
2SC1740S-R,S
RL901
F901
6.3A/125V
+13VS
+13VS
MPUGND
POWER
1K
P912
P911
TO NNAF-7875
P931A
NAPS-7876
U18
TERMINAL
PC BOARD
P912A
P911A
3
7
JL6805B
BRLD
FRLD
CSRLD
+24V
TO NAAF-7875
JL6804B
LSPE
RSPE
CSPE
LSSPE
RSSPE
3
TO NAAF-7875
U19
POWER SUPPLY PC BOARD
P917
P918
4
P901
AC-H
120V 60HZ
AC-G
P901A
NC
J6306
E921
J5320
R921
C921
223Z
C923
223Z
D921-D924
GP104003E OR
RL1N4003
T902
NPT-1492D
AC OUTLET
120W 1A MAX
D921
D923
C922
220/35
D922
D924
5
NOTE
THE COMPONENTS IDENTIFIED BY MARK ARE CRITICAL FOR SAFETY
REPLACE ONLY WITH PART NUMBER SPECIFIED.
VOLTAGE (MEASURED WITH VOLTMETER) IS DC VOLTAGE.(NO INPUT SIGNAL).
ALL PNP TRANSISTORS ARE EQUIVALENT TO 2SA1015-GR UNLESS OTHERWISE NOTED.
ALL NPN TRANSISTORS ARE EQUIVALENT TO 2SC1815-GR UNLESS OTHERWISE NOTED.
ALL DIODES ARE EQUIVALENT TO 1SS133 UNLESS OTHERWISE NOTED.
ELECTROLYTIC CAPACITORS ( ) ARE IN uF/WV.
ALL CAPACITORS ARE IN pF/50WV UNLESS OTHERWISE NOTED.
EX) 030- 3pF 330- 33pF 331- 330pF 333- 0.033uF
ALL RESISTORS ARE IN OHMS 1/4WATTS UNLESS OTHERWISE NOTED.
THE THICK LINES ON PC BOARD ARE THE PRINTING SIDE OF THE PARTS.
EX) PRINTING SIDE
CIRCUIT IS SUBJECT TO CHANGE FOR IMPROVEMENT.
<Note>
NC=No mount of parts.
CAUTION
FOR CONTINUED PROTECTION
AGAINST FIRE HAZARD, REPLACE
ONLY WITH FUSE OF SAME TYPE
VA
AND RATING INDICATED.
THIS SYMBOL LOCATED NEAR THE FUSE INDICATES
THAT THE FUSE USED IS SLOW OPERATING TYPE
FOR CONTINUED PROTECTION AGAINST FIRE
HAZARD,REPLACE WITH SAME TYPE FUSE. FOR FUSE
RATING REFER TO THE MARKING ADJACENT TO THE SYMBOL.
ATTENTION
AFIN D'ASSURER UNE PROTECTION
PERMANENTE CONTRE LES RISQUES
D'INCENDIE, REMPLACER UNIQUEMENT
VA
PAR UN FUSIBLE DE MEME TYPE
ET CALIBRATION COMME INDIQUE.
!
NAETC-7868
U10
REGULATOR PC BOARD
Q6931
NJM78M56FA
C6933
10/16
O
G
I
120
(2W)
S3GND
+13VS
POWER
PRO
C6932
103Z
C6931
1000/25
D6932
D6932,6933:
GP104003E OR
RL1N4003
SPF
SPCS
SPB
SE1H
VOLH/THPRO
MPUGND
+24V
AGND
HPR
HPL
D6933
R6935
P6931A
FLAC1
FLAC2
MPUGND
MPUGND
HPL
AGND
HPR
+5.6V
+24V
S3
S3GND
S3GND
S3
S2
S2
S2
S2
+5.6V
POWER
SPF
SPCS
SE1H
SPB
VOLH/THPRO
PRO
MPUGND
+13VS
P7503B
TO NADIS-7403
P410A
TO NADG-7401
P411A
TO NADG-7401
CE SYMBOLE INDIQUE QUE LE FUSIBLE UTLISE EST
E LENT.POUR UNE PROTECTION PERMANENTE,N'UTILISER
QUE DES FUSIBLES DE MEME TYPE. CE DARNIER EST
INDIQUE LA QU LE PRESENT SYMBOL EST APPOSE.
NAETC-7869
U11
TERMINAL PC BOARD
T901
NPT-1510D
THERMAL FUSE
8
9
10
11
12
13
14
15
16
17
18
19
JL6951B
TO NAAF-7875
R9501
1
F9501
R9521
3.9
(1/2W)
C9513
223Z
R9502
(1/2W)
0.47
(1/2W)
NC
R9503
(1/2W)
0.22
U20
TERMINAL PC BOARD
JL6952B
TO NAAF-7875
JL9501B
TO NAAF-7875
JL9501
NAPS-7878
Loading...
+ 46 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.