Onkyo SKM-550S, SKF-550F, SKC-550C, HT-R550, SKB-550 User Manual

...
7.1ch Home Theater System
HT-SR800
Instruction Manual
Contents
Introduction ..................................... 2
Connection .................................... 19
Turning On & First Time Setup..... 36
Basic Operation
Playing your AV components....... 42
Listening to the Radio.................. 44
Thank you for purchasing an Onkyo 7.1ch Home Theater System. Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new 7.1ch Home Theater Sys­tem. Please retain this manual for future reference.
Enjoying the Listening Modes ..... 48
Advanced Operation..................... 55
Troubleshooting ............................ 65
E
n
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

Important Safety Instructions

1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radia­tors, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are pro­vided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience recepta­cles, and the point where they exit from the appara­tus.
11. Only use attachments/accessories specified by the manufacturer.
12.
Use only with the cart, stand, tripod, bracket, or table spec­ified by the manufacturer, or sold with the apparatus. When a cart is used, use cau­tion when moving the cart/ apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
PORTABLE CART WARNING
S3125A
WARNING
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to
persons. The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
AVIS
RISQUE DE CHOC ELECTRIQUE
NE PAS
OUVRIR
15. Damage Requiring Service Unplug the apparatus from the wall outlet and refer servicing to qualified service personnel under the following conditions: A. When the power-supply cord or plug is damaged, B. If liquid has been spilled, or objects have fallen
into the apparatus,
C. If the apparatus has been exposed to rain or
water,
D. If the apparatus does not operate normally by
following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the apparatus to its normal operation,
E. If the apparatus has been dropped or damaged in
any way, and
F. When the apparatus exhibits a distinct change in
performance this indicates a need for service.
16. Object and Liquid Entry Never push objects of any kind into the apparatus through openings as they may touch dangerous volt­age points or short-out parts that could result in a fire or electric shock. The apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases shall be placed on the apparatus. Don’t put candles or other burning objects on top of this unit.
17. Batteries Always consider the environmental issues and fol­low local regulations when disposing of batteries.
18. If you install the apparatus in a built-in installation, such as a bookcase or rack, ensure that there is ade­quate ventilation. Leave 20 cm (8") of free space at the top and sides and 10 cm (4") at the rear. The rear edge of the shelf or board above the apparatus shall be set 10 cm (4") away from the rear panel or wall, creating a flue-like gap for warm air to escape.
2

Precautions

1. Recording Copyright
only, recording copyrighted material is illegal with­out the permission of the copyright holder.
2. AC Fuse
serviceable. If you cannot turn on the unit, contact your Onkyo dealer.
3. Care
over with a soft cloth. For stubborn stains, use a soft cloth dampened with a weak solution of mild deter­gent and water. Dry the unit immediately afterwards with a clean cloth. Don’t use abrasive cloths, thin­ners, alcohol, or other chemical solvents, because they may damage the finish or remove the panel let­tering.
4. Power WARNING
BEFORE PLUGGING IN THE UNIT FOR THE FIRST TIME, READ THE FOLLOWING SEC­TION CAREFULLY. AC outlet voltages vary from country to country.
Make sure that the voltage in your area meets the voltage requirements printed on the unit’s rear panel (e.g., AC 230–240 V, 50 Hz or AC 120 V, 60 Hz).
The power cord plug is used to disconnect this unit from the AC power source. Make sure that the plug is readily operable (easily accessible) at all times.
Pressing the [STANDBY/ON] button to select Standby mode does not fully shutdown the unit. If you do not intend to use the unit for an extended period, remove the power cord from the AC outlet.
5. Never Touch this Unit with Wet Hands
handle this unit or its power cord while your hands are wet or damp. If water or any other liquid gets inside this unit, have it checked by your Onkyo dealer.
6. Handling Notes
• If you need to transport this unit, use the original
• Do not leave rubber or plastic items on this unit
• This unit’s top and rear panels may get warm
• If you do not use this unit for a long time, it may
—The AC fuse inside the unit is not user-
—Occasionally you should dust the unit all
packaging to pack it how it was when you origi­nally bought it.
for a long time, because they may leave marks on the case.
after prolonged use. This is normal.
not work properly the next time you turn it on, so be sure to use it occasionally.
—Unless it’s for personal use
—Never
For U.S. models
FCC Information for User
CAUTION:
The user changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interfer­ence in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accor­dance with the instructions, may cause harmful interfer­ence to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful inter­ference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dif­ferent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV tech­nician for help.
For Canadian Models
NOTE:
COMPLIES WITH CANADIAN ICES-003. For models having a power cord with a polarized plug:
CAUTION:
MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
THIS CLASS B DIGITAL APPARATUS
TO PREVENT ELECTRIC SHOCK,
Modèle pour les Canadien
REMARQUE:
LA CLASSE B EST CONFORME À LA NORME NMB-003 DU CANADA. Sur les modèles dont la fiche est polarisée:
ATTENTION:
TRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRE­SPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.
CET APPAREIL NUMÉRIQUE DE
POUR ÉVITER LES CHOCS ÉLEC-
3

Speaker Precautions

Placement
• The speaker cabinets are made out of wood and are therefore sensitive to extreme temperatures and humidity, do not put them in locations subject to direct sunlight or in humid places, such as near an air condi­tioner, humidifier, bathroom, or kitchen.
• Do not put water or other liquids close to the speakers. If liquid is spilled over the speakers, the drive units may be damaged.
• Speakers should only be placed on sturdy, flat surfaces that are free from vibration. Putting them on uneven or unstable surfaces, where they may fall and cause dam­age, will affect the sound quality.
• Subwoofer is designed to be used in the upright verti­cal position only. Do not use it in the horizontal or tilted position.
• If the unit is used near a turntable, CD player or DVD player, howling or slipping of sound may occur. To prevent this, move the unit away from the turntable, CD player or DVD player otherwise lower the unit’s output level.
Using Close to a TV or Computer
TVs and computer monitors are magnetically sensitive devices and as such are likely to suffer discoloration or picture distortion when conventional speakers are placed nearby. To prevent this, the SKF-550F and SKC-550C feature internal magnetic shielding. In some situations, however, discoloration may still be an issue, in which case you should turn off your TV or monitor, wait 15 to 30 minutes, and then turn it back on again. This normally activates the degaussing function, which neutralizes the magnetic field, thereby removing any discoloration effects. If discoloration problems persist, try moving the speakers away from your TV or monitor. Note that discol­oration can also be caused by a magnet or demagnetizing tool that’s too close to your TV or monitor.
Input Signal Warning
The speakers can handle the specified input power when used for normal music reproduction. If any of the follow­ing signals are fed to them, even if the input power is within the specified rating, excessive current may flow in the speaker coils, causing burning or wire breakage:
1.
Interstation noise from an untuned FM radio.
2.
Sound from fast-forwarding a cassette tape.
3.
High-pitched sounds generated by an oscillator, elec­tronic musical instrument, and so on.
4.
Amplifier oscillation.
5.
Special test tones from audio test CDs and so on.
6.
Thumps and clicks caused by connecting or discon­necting audio cables (Always turn off your amplifier before connecting or disconnecting cables.)
7.
Microphone feedback.
4

Enjoying Home Theater

Speaker Sets A and B
You can use two sets of speakers with the AV receiver:
Speaker set A
*While speaker set B is on, speaker set A is reduced to 5.1-channel playback.
Speaker set B
*Only analog input sources are output by speaker set B.
Speaker set A Speaker set B Indicator Output
(included speakers) should be used in your main listening room for up to 7.1-channel playback.
(not included) can be used in another room and offers 2-channel stereo playback.
TUNING
PRESET
AB
SPEAKERS
D
SETUP ENTER
SETUP MIC
TUNING MODE
CLEAR
A B
A
On
Off
STANDBY/ON
STANDBY
MULTI CH C
PHONES
ABSPEAKERS
AUXCBL/SATVCR/DVR
DVD
TONE DISPLAYSTEREO DIMMER MEMORY
LISTENING MODE
TUNERTAPE
DIGITAL INPUT
On
Off Set A: 7.1 channels
On Set B: 2 channels
Off No sound
RETURN
VIDEO
speaker set A
MASTER VOLUME
or
AUX INPUT
AUDIOLR
B
Set A: 5.1 channels Set B: 2 channels
and
speaker set B
.
CH
TV
DISC
VOL
INPUT
GUIDE
TOP MENU
SP A / B
PLAYLIST/CAT PLAYLIST/CAT
SETUP RETURN
ALBUM
ENTER
VOL
PREVIOUS
MENU
MUTING
Main Room (speaker set A, the supplied speakers)
Center speaker
Front right
speaker
Surround
right
speaker
right speaker
Subwoofer
Surround
left
speaker
Front left
speaker
Surround back
Surround back
left speaker
* While speaker set B is on, the surround
back speakers output no sound.
Sub Room (speaker set B)
* Digital input sources are not output
by speaker set B. Connect your source component with an analog connection.
5

Package Contents

Make sure you have the following items:
AV receiver (HT-R550)
Surround and Surround back speakers (SKM-550S/SKB-550)
Remote controller and two batteries (AA/R6)
Indoor FM antenna
AM loop antenna
Speaker setup microphone
Speaker terminal tool
Subwoofer (SKW-550)
(Red) (White)
Speaker cable for front speakers 11 ft. (3.5 m)
(Green)
Speaker cable for center speaker 10 ft. (3 m)
(Blue) (Gray)
(Brown) (Tan)
Speaker cables for surround speakers 30 ft. (9 m)
Front speakers (SKF-550F)
Center speaker (SKC-550C)
6
RCA cable for subwoofer connection 10 ft. (3 m)
4 floor pads for the subwoofer
* In catalogs and on packaging, the letter at the end of the
product name indicates the color. Specifications and oper­ation are the same regardless of color.

Features

Amplifier
• 7-channel amplifier
• 110 watts per channel rms into 8 ohms, 2 channels driven at 1 kHz, less than 0.9% total harmonic distor­tion (FTC rating)
• WRAT (Wide Range Amplifier Technology)
• Optimum Gain Volume Circuitry
• Audyssey 2EQ/HTIB room correction
*1
Processing
• Dolby*2 Digital EX and Dolby Pro Logic IIx
• DTS, DTS-ES Matrix/Discrete, DTS Neo:6, and DTS
*3
96/24
• Neural Surround
*4
(North American models only)
• Theater-Dimensional*5 virtual surround sound
• Linear PCM 192 kHz/24-bit D/A converters on all channels
• Pure Audio listening mode (not North American model)
•Powerful and highly accurate 32-bit DSP processing
Audio/Video
•2 HDMI*6 inputs, 1 output
• Adjustable crossover (40, 50, 60, 80, 100, 120, 150, 200 Hz)
• HDTV-capable component video (3 inputs, 1 output)
•3 S-Video inputs, 2 outputs
•4 assignable digital inputs (2 optical, 2 coaxial)
• Subwoofer pre out
• Color-coded 7.1 multichannel input for use with Super Audio CD and DVD-Audio
• A/B speaker drive
• Color-coded speaker terminal posts
*1
Manufactured under license from Audyssey Laboratories. U.S. and foreign patents pending. Audyssey 2EQ/HTIB is a trademark of Audyssey Laboratories.
*2
Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic” and the double-D symbol are regis­tered trademarks of Dolby Laboratories.
*3
“DTS” and “DTS-ES | Neo: 6” are registered trademarks of DTS, Inc. “96/24” is a trademark of DTS, Inc.
*4
Neural Surround name and related logos are trademarks owned by Neural Audio Corporation.
*5
Theater-Dimensional is a trademark of Onkyo Corpora­tion.
*6
HDMI, the HDMI logo and High Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing, LLC. This unit incorporates HDMI technology.
*7
®
XM Ready Radio Inc. All rights reserved.
is a registered trademark of XM Satellite
Tuner
•XM*7 Satellite Radio (North American models only)
*XM Passport System required; sold separately.
• SIRIUS*8 Satellite Radio (North American models only)
• 40 radio presets
• AM/FM auto tuning
Remote Controller
• Preprogrammed for use with other AV components
Speaker
• Color-coded speaker terminals and speaker cables
• Subwoofer Auto standby function
• Magnetically shielded front and center speakers
*8
©2005 SIRIUS Satellite Radio Inc. “SIRIUS,” the SIRIUS dog logo, channel names and logos are trademarks of SIR­IUS Satellite Radio Inc. Available only in the contiguous United States (excluding Alaska and Hawaii) and Canada.
7
Getting Started in Five Easy Steps
1. Hookup
Connect the speakers and your AV components to the AV receiver.
page 19
XM
SIRIUS
HDMI
ASSIGNABLE
OUT
IN 1IN 2
ANTENNA
FMAM75
DIGITAL IN
ASSIGNABLE
COAX­IAL 1
(DVD)
2
(CBL/SAT)
OPTICAL
1
(VCR/DVR)
2
(CD)
REMOTE CONTROL
OUT
CBL/SAT IN
VCR/DVR IN
DVD IN
COMPONENT VIDEO
OUT
IN IN
RR
CD
TAPE
Y
C
B/PB
CR/PR
LL
L
MONITOR
CBL/SAT
VCR/DVR
DVD
OUT
V
R
V
S
S
SURROUND BACK
SPEAKERS
OUT
IN IN
FRONT
SURROUND
SURR BACK
CENTER
INININ
OUT
L
R
SUB
WOOFER
CBL/SAT
VCR/DVR
DVD
L
R
SURROUND
FRONT
CENTER
SPEAKERS
SPEAKERS A
SPEAKER
PRE OUT
L
SUB WOOFER
L
R
R
FRONT
SPEAKERS B
2. Turning On
With the hookup complete, you’re ready to switch on.
page 36
3. First Time Setup
A few simple settings to get the very best from your system.
page 37
HDMI Video
Setup
Automatic
Speaker Setup
4. Playing Your AV Components
Enjoying movies and music.
page 42
5. Using the Listening Modes
Time to really enjoy your home theater system!
page 48
Digital Input
Input Display
8

Contents

Introduction
Important Safety Instructions ....................2
Precautions .................................................3
Speaker Precautions ..................................4
Enjoying Home Theater..............................5
Speaker Sets A and B ...................................5
Package Contents.......................................6
Features .......................................................7
Getting to Know the AV Receiver............10
Remote Controller.....................................13
Speakers ....................................................18
Connection
Connecting Your Speakers ......................19
Connecting Antennas...............................22
Connecting Your Components ................24
About AV Connections ................................24
Connecting Audio and Video Signals
to the AV Receiver .................................... 25
Which Connections Should I Use?..............25
TV or Projector DVD player
Components with HDMI ..............................29
VCR or DVD Recorder for Playback ...........30
VCR or DVD Recorder for Recording.......... 31
Camcorder, Games Console,
or Other Device.........................................31
Satellite, Cable, Set-top box,
or Other Video Source ..............................32
CD Player or Turntable................................33
RI Dock........................................................34
Cassette, CDR, MiniDisc,
or DAT Recorder.......................................34
Connecting Onkyo Components
Connecting the Power Cord ........................35
..........................................26
.................................................27
..........35
Turning On & First Time Setup
Basic Operation
Playing Your AV Components ................ 42
Basic AV Receiver Operation ..................... 42
Using the Multichannel DVD Input.............. 43
Displaying Source Information.................... 43
Listening to the Radio.............................. 44
Listening to AM/FM Stations....................... 44
Presetting AM/FM Stations ......................... 45
Common Functions.................................. 46
Setting the Display Brightness.................... 46
Adjusting the Bass and Treble.................... 46
Muting the AV Receiver .............................. 46
Using the Sleep Timer ................................ 47
Using Headphones ..................................... 47
Adjusting Speaker Levels ........................... 47
Enjoying the Listening Modes
Using the Listening Modes...................... 48
Selecting Listening Modes.......................... 48
About the Listening Modes ......................... 50
Using the Late Night Function
(Dolby Digital only) ................................... 52
Using the CinemaFILTER........................... 52
Using the Audio Adjust Settings ................. 52
Advanced Operation
Recording.................................................. 55
Advanced Setup ....................................... 56
Advanced Speaker Settings ....................... 56
Digital Input Signal Formats ....................... 61
Correcting Sound and Picture Sync ........... 61
Controlling Other Components............... 62
Entering Remote Control Codes................. 62
Remote Control Codes for Onkyo
Components Connected via .............. 63
Resetting REMOTE MODE Buttons ........... 63
Resetting the Remote Controller ................ 63
Turning On the AV Receiver ....................36
First Time Setup........................................37
Automatic Speaker Setup
(Audyssey 2EQ/HTIB)...............................37
HDMI Video Setup.......................................40
Digital Audio Input Setup.............................41
Changing the Input Display .........................41
Troubleshooting ....................................... 65
If you can’t resolve an issue, try resetting the AV receiver by holding down the [VCR/DVR] button and pressing the [STANDBY/ON] button.
Specifications ........................................... 69
9

Getting to Know the AV Receiver

Front Panel

North American Model
2
1
STANDBY/ON
STANDBY
3 5 6 74
TUNING
MASTER VOLUME
PRESET
MULTI CH C D
PHONES
ABSPEAKERS
DVD
TONE DISPLAYSTEREO DIMMER MEMORY
Other Models
STANDBY/ON
STANDBY
PURE AUDIO
DVDMULTI CHPURE AUDIO C D
PHONES
ABSPEAKERS
TONE
V
For detailed information, see the pages in parentheses.
A
STANDBY/ON button (36)
Sets the AV receiver to On or Standby.
STANDBY indicator (36)
B
Lights up when the AV receiver is on Standby and flashes while a signal is being received from the remote controller.
C
Remote-control sensor (13)
Receives control signals from the remote controller.
Display
D
See “Display” on page 11.
Input selector buttons (42)
E
Select the input sources. The [MULTI CH] button selects the multichannel
DVD input.
AUXCBL/SATVCR/DVR
LISTENING MODE
AUXCBL/SATVCR/DVR
LISTENING MODE
TUNERTAPE
DIGITAL INPUT
TUNING MODE
CLEAR
SETUP ENTER
SETUP MIC
RETURN
AUX INPUT
VIDEO
AUDIOLR
UJKLMNOPQ8 9RTS
MASTER VOLUME
TUNING
PRESET
TUNERTAPE
DISPLAYSTEREO DIMMER MEMORY
DIGITAL INPUT
Arrow/TUNING/PRESET and ENTER buttons
F
TUNING MODE
CLEAR
When the tuner is selected, the TUNING [ ] [ ] buttons are used for radio tuning, and the PRESET
[] [ ] buttons are used to select radio presets (see page 45). With the setup menus, they work as arrow buttons and are used to select and set items. The ENTER button is also used with the setup menus.
G
MASTER VOLUME control (42)
Sets the volume of the AV receiver to MIN, 1 through 79, or MAX.
H
PHONES jack (47)
This 1/4-inch phone jack is for connecting a stan­dard pair of stereo headphones for private listening.
SPEAKERS A and B buttons (5, 42)
I
Turn speaker sets A and B on or off.
SETUP ENTER
SETUP MIC
RETURN
AUX INPUT
VIDEO
AUDIOLR
10
Getting to Know the AV Receiver
—Continued
TONE, [–], and [+] buttons (46)
J
Used to adjust the bass and treble.
STEREO button (48)
K
Selects the Stereo listening mode.
LISTENING MODE [ ]/[ ] buttons (48)
L
Select the listening modes.
DISPLAY button (43)
M
Displays various information about the currently selected input source.
DIGITAL INPUT button (41, 61)
N
Used to assign the digital inputs and to specify the format of digital input signals.
O
DIMMER button (46)
Adjusts the display brightness.
MEMORY button (45)
P
Used when storing or deleting radio presets.

Display

TUNING MODE button (44)
Q
Selects the Auto or Manual tuning mode for AM and FM radio.
R
SETUP button
Used to access the setup menus.
SETUP MIC (38)
S
The automatic speaker setup microphone connects here.
T
RETURN button
Selects the previously displayed setup menu.
AUX INPUT (31, 55)
U
Used to connect a camcorder, games console, and so on. There are jacks for composite video and analog audio.
V
PURE AUDIO button and indicator (48)
The North American model doesn’t have this button and indicator.
Selects the Pure Audio listening mode. The indica­tor lights up when this mode is selected.
213 5
6
For detailed information, see the pages in parentheses.
A and B speaker indicators (5, 42)
1
Indicator A lights up when speaker set A is on. Indi­cator B lights up when speaker set B is on.
2
MUTING indicator (46)
Flashes while the AV receiver is muted.
Input signal format indicators
3
Show the audio signal format of the current input source.
4
Listening mode indicators (50)
Show the selected listening mode.
Radio indicators
5
FM STEREO (44):
reo FM station.
Lights up when tuned to a ste-
4
7
8
AUTO (44):
Auto Tuning mode is selected, and disappears when Manual Tuning mode is selected.
TUNED (44):
tion.
6
SLEEP indicator (47)
Lights up when the Sleep function has been set.
7
Message area
Displays various information about the selected input source.
8
Audyssey indicator (37)
Lights up during automatic speaker setup.
For AM and FM radio, lights up when
Lights up when tuned to a radio sta-
11
Getting to Know the AV Receiver

Rear Panel

7 8
1 2 53 6
DIGITAL IN
ASSIGNABLE
COAX­IAL
1
(DVD)
2
(CBL/SAT)
OPTICAL
1
(VCR/DVR)
2
(CD)
REMOTE CONTROL
CBL/SAT IN
IN 1IN 2
Y
B/PB
C
CR/PR
OUT
VCR/DVR IN
DVD IN
COMPONENT VIDEO
OUT
IN IN
RR
CD
LL
TAPE
4
HDMI
ASSIGNABLE
OUT
V
S
L
R
CBL/SAT
CBL/SAT
ANTENNA
VCR/DVR
OUT
IN
IN
OUT
VCR/DVR
FMAM75
IN IN
IN
FRONT
SIRIUS
MONITOR
DVD
OUT
SURROUND
DVD
—Continued
(North American model only)
9
XM
L
V
R
S
SURROUND BACK
SPEAKERS
SURR BACK
CENTER
SUB
WOOFER
SURROUND SPEAKERS
L
R
PRE OUT
SUB
WOOFER
SPEAKERS A
FRONT
L
R
SPEAKERS B
FRONT
L
R
CENTER
SPEAKER
J K L M N O
A
DIGITAL IN OPTICAL 1, 2 and COAXIAL 1, 2
These optical and coaxial digital audio inputs are for connecting components with optical or coaxial digital audio outputs, such as CD and DVD players.
B
HDMI IN 1, 2, and OUT
These jacks are for connecting HDMI-compatible components. Audio and video signals received by the HDMI IN jacks pass through to the HDMI OUT jack.
COMPONENT VIDEO
C
A DVD player, TV, or other component that sup­ports component video can be connected here.
AM ANTENNA
D
These push terminals are for connecting an AM antenna.
FM ANTENNA
E
This jack is for connecting an FM antenna.
MONITOR OUT
F
The S-Video or composite video output should be connected to a video input on your TV or projector.
SIRIUS antenna (North American models
G
only)
This jack is for connecting a SIRIUS Satellite Radio antenna (see the separate SIRIUS instructions).
H
XM antenna (North American models only)
This jack is for connecting an XM Passport System, sold separately (see the separate XM instructions).
I
FRONT SPEAKERS A, SURROUND SPEAKERS, CENTER SPEAKER, and SURROUND BACK SPEAKERS
These terminal posts are for connecting speaker set A.
P
J
K
L
M
N
O
P
REMOTE CONTROL
This Remote Interactive jack can be connected to the jack on another -capable Onkyo com­ponent. To use , you must make an analog audio
connection (RCA) between the AV receiver and the other component, even if they are connected digi­tally.
CD IN
This analog audio input is for connecting a CD player’s analog audio output.
TAPE IN/OUT
This analog audio input and output are for connect­ing a recorder with an analog audio input and out­put, such as a cassette deck, MD recorder, etc.
VCR/DVR IN/OUT and CBL/SAT IN
The VCR/DVR inputs and outputs can be used to connect a VCR or DVR (digital video recorder).
The CBL/SAT inputs can be used to connect a cable/satellite receiver, set-top box, etc.
DVD IN
These jacks can be used to connect a DVD player with an analog multichannel audio output for SACD and DVD-Audio playback.
SUBWOOFER PRE OUT
A powered subwoofer can be connected here.
FRONT SPEAKERS B
These push terminals are for connecting speaker set B.
See pages 19–35 for hookup information.
12

Remote Controller

Installing the Batteries

To open the battery compartment, press
1
the small hollow and slide open the cover.
Insert the two supplied batteries (AA/R6)
2
in accordance with the polarity diagram
inside the battery compartment.
Slide the cover shut.
3
Notes:
• If the remote controller doesn’t work reliably, try replacing the batteries.
• Don’t mix new and old batteries or different types of batteries.
• If you intend not to use the remote controller for a long time, remove the batteries to prevent damage from leakage or corrosion.
• Expired batteries should be removed as soon as possi­ble to prevent damage from leakage or corrosion.

Aiming the Remote Controller

When using the remote controller, point it toward the AV receiver’s remote control sensor, as shown below.
Remote control sensor
AV receiver
STANDBY indicator
Approx. 16 ft. (5 m)
Notes:
• The remote controller may not work reliably if the AV receiver is subjected to bright light, such as direct sun­light or inverter-type fluorescent lights. Keep this in mind when installing.
• If another remote controller of the same type is used in the same room, or the AV receiver is installed close to equipment that uses infrared rays, the remote control­ler may not work reliably.
• Don’t put anything on top of the remote controller, such as a book or magazine, because a button may be pressed continuously, thereby draining the batteries.
• The remote controller may not work reliably if the AV receiver is installed in a rack behind colored glass doors. Keep this in mind when installing.
• The remote controller will not work if there’s an obsta­cle between it and the AV receiver’s remote control sensor.
13
Remote Controller
—Continued

Using the Remote Controller

Including the AV receiver, the remote controller can be used to control up to seven different components. The remote controller has a specific operating mode for use with each type of component. Modes are selected by using the six REMOTE MODE buttons.

RECEIVER/TAPE Mode

In RECEIVER/TAPE mode, you can control the AV receiver and an Onkyo cassette recorder connected via .
DVD and CD/MD/CDR/DOCK Modes
With these modes, you can control a DVD player and CD player, MD recorder, CDR, or RI dock. By entering the appropriate remote control code, you can control Onkyo components or components made by other manufactur­ers (see page 62).
TV, VCR and SAT/CABLE Modes
With these modes, you can control a TV, VCR, and satellite or cable receiver. You must enter the appropriate remote control code first (see page 62).
1
REMOTE MODE
RECEIVER
TAPE/AMP
Press one of the REMOTE MODE buttons to select a mode.
DVD
M D/CDR
D
C
DOCK
TV
VCR
CABLE
SAT
RECEIVER
TAPE/AMP
DVD
M D/CDR
C
D
DOCK
TV
VCR
CABLE
SAT
RECEIVER/TAPE Mode
RECEIVER/TAPE mode is used to control the AV receiver. It can also be used to control an Onkyo cassette recorder connected via .
RECEIVER
TAPE/AMP
K
L
M
N
O
1
2
3
1
2
3
5
6
7
4
STANDBY/ON
INPUT SELECTOR
123
VCR/DVR
456
AUX
789
10 11 12
+
10
D TUN
--/---
TV
INPUT
GUIDE
TOP MENU
SP A / B
PLAYLIST/CAT PLAYLIST/CAT
SETUP RETURN
CBL/SAT
MULTI CH
0
DIMMER
VOL
REMOTE MODE
RECEIVER
TAPE/AMP
DVD
CLR
ENT
SLEEP
DISC
ALBUM
ENTER
DVD
M
D/CDR
C D
DOCK
TV
VCR
C DTAPE TUNER
CABLE
SAT
CH
VOL
PREVIOUS
MENU
MUTING
4
LISTENING MODE
SURROUND
8
9
J
STEREO
RANDOM
SUBTITLE
AUDIO REPEAT
TEST TONE
CH SEL
PLAY MODE
DISPLAY
LEVEL
L NIGHT
-
LEVEL
CINE FLTR
HDDDVDVCR
+
P Q
2
Use the buttons supported by that mode to control the compo­nent.
RECEIVER/TAPE mode:
see right column
DVD mode:
see page 16
CD/MD/CDR/DOCK mode:
see page 17
TV, VCR, SAT/CABLE modes:
see page 64
Note:
Some of the remote controller operations described in this manual may not work as expected with other com­ponents.
14
Buttons
1, 2, 3
, and 4 are used when the TUNER
or TAPE input is selected.
-
681M
RC
Remote Controller
—Continued
For detailed information, see the pages in parentheses.
A
STANDBY/ON button (36)
Sets the AV receiver to On or Standby.
B
INPUT SELECTOR buttons (42)
Used to select the input sources.
MULTI CH button (43)
C
Selects the multichannel DVD input.
DIMMER button (46)
D
Adjusts the display brightness.
E
SP A/B button (5, 42)
Used to turn speaker sets A and B on or off.
F
Arrow [ ]/[ ]/[ ]/[ ] and ENTER buttons
Used to select and adjust settings.
G
SETUP button
Used to access the setup menus.
LISTENING MODE buttons (48)
H
Used to select the listening modes. These buttons work in all remote controller modes.
STEREO button
Selects the Stereo listening mode.
SURROUND button
Selects the Dolby and DTS listening modes and the Neural Surround listening mode (North American model only).
[ ]/[ ] buttons
Used to select the available listening modes.
I
TEST TONE, CH SEL, LEVEL-, and LEVEL+ buttons (47, 59)
Used to adjust the level of each speaker.
J
DISPLAY button (43)
Displays various information about the selected input source.
K
REMOTE MODE buttons (14)
Used to select the remote controller modes. When a remote controller button is pressed, the REMOTE MODE button for the currently selected mode lights up.
SLEEP button (47)
L
Used with the Sleep function.
VOL [ ]/[ ] button (42)
M
Adjusts the volume of the AV receiver regardless of the currently selected remote controller mode.
N
MUTING button (46)
Mutes or unmutes the AV receiver.
RETURN button
O
Selects the previously displayed setup menu.
P
CINE FLTR button (52)
Used with the CinemaFILTER function.
Q
L NIGHT button (52)
Used with the Late Night function.
Buttons used when the TUNER input is selected
To select the Tuner (AM/FM) as the input source, press:
RECEIVER
1
Number, D TUN, and ENT buttons (45)
Used to select AM and FM radio stations directly.
2
CH +/– button (45)
Used to select radio presets.
3
Arrow [ ]/[ ] buttons
For AM and FM, the Up and Down [ ]/[ ] but­tons are used for tuning.
Buttons used when the TAPE input is selected
To select your Cassette deck as the input source, press:
RECEIVER
Playback buttons
4
On twin cassette decks, only deck B can be con­trolled.
Play [ ] button
Starts playback.
Stop [ ] button
Stops playback.
Reverse Play [ ] button
Starts reverse playback.
Rewind and FF [ ]/[ ] buttons
The Rewind [ ] button starts rewind. The FF [] button starts fast forward.
8
TUNER
7
TAPE
15
Remote Controller
—Continued

DVD Mode

By default, the remote controller is set to control an Onkyo DVD player.
To select your DVD player as the input source, press:
6
DVD
REMOTE MODE
RECEIVER
TAPE/AMP
DVD
ENT
SLEEP
ALBUM
ENTER
C DTAPE TUNER
CLR
CH
DISC
or
DVD
M
D/CDR
C D
DOCK
TV
VCR
CABLE
SAT
VOL
PREVIOUS
MENU
MUTING
5
MULTI CH
DVD
K
L
M
1
2
3
4
5
6
RECEIVER
STANDBY/ON
INPUT SELECTOR
123
CBL/SAT
V
CR/DVR
456
AUX
MULTI CH
789
10 11 12
+
0
10
D TUN
--/---
DIMMER
TV
VOL
INPUT
GUIDE
TOP MENU
SP A / B
PLAYLIST/CAT PLAYLIST/CAT
SETUP RETURN
7
LISTENING MODE
SURROUND
8 9
J
STEREO
RANDOM
SUBTITLE
AUDIO REPEAT
TEST TONE
CH SEL
PLAY MODE
DISPLAY
LEVEL
L NIGHT
-
LEVEL
CINE FLTR
HDDDVDVCR
+
N O
P
Q
-
RC
681M
A
STANDBY/ON button
Sets the DVD player to On or Standby.
B
Number buttons
Used to enter title, chapter, and track numbers and times for locating specific points.
C
DISC +/– button
Selects discs on a DVD changer.
TOP MENU button
D
Selects a DVD’s top menu.
Arrow [ ]/[ ]/[ ]/[ ] and ENTER buttons
E
Used to navigate DVD menus and the DVD player’s onscreen setup menus.
SETUP button
F
Used to access the DVD player’s onscreen setup menus.
Playback buttons
G
From left to right: Pause, Play, Stop, Fast Reverse, Fast Forward, Previous, and Next.
SUBTITLE button
H
Selects subtitles.
AUDIO button
I
Selects foreign language soundtracks and audio for­mats (e.g., Dolby Digital or DTS).
DISPLAY button
J
Displays information about the current disc, title, chapter, or track, including elapsed time, remaining time, total time, and so on.
CLR button
K
Cancels functions and clears entered numbers.
MENU button
L
Displays a DVD’s menu.
M
RETURN button
Exits the DVD player’s onscreen setup menus.
N
RANDOM button
Used with the random playback function.
REPEAT button
O
Used with the repeat playback functions.
VCR, DVD, and HDD buttons
P
Used to select VCR, HDD (hard disk drive), or DVD playback on a VCR/DVD recorder with a built-in hard disk drive.
PLAY MODE button
Q
Selects play modes on components with selectable play modes.
16
Remote Controller
—Continued

CD/MD/CDR/DOCK Mode

By default, the remote controller is set to control an Onkyo CD player.
To select the input source, press:
9
C D
RECEIVER
TAPE
7
TAPE
7
or
* If you’re using an MD, CDR, or an RI Dock, you must
change the Input Display (see page 41).
STANDBY/ON
1
INPUT SELECTOR
2
3
4 5
123
CBL/SAT
V
CR/DVR
456
AUX
MULTI CH
789
10 11 12
+
0
10
D TUN
--/---
DIMMER
TV
VOL
INPUT
GUIDE
TOP MENU
SP A / B
PLAYLIST/CAT PLAYLIST/CAT
SETUP RETURN
CD player
MD or CD recorder
RI Dock
2
CBL/SAT
REMOTE MODE
RECEIVER
TAPE/AMP
M
DVD
C DTAPE TUNER
CLR
ENT
SLEEP
CH
DISC
ALBUM
PREVIOUS
MUTING
ENTER
DVD
D/CDR
C D
DOCK
TV
VCR
CABLE
SAT
VOL
MENU
M D/CDR
C D
DOCK
8
9
J
6
LISTENING MODE
SURROUND
7
STEREO
RANDOM
SUBTITLE
AUDIO REPEAT
TEST TONE
CH SEL
PLAY MODE
DISPLAY
LEVEL
L NIGHT
-
LEVEL
CINE FLTR
HDDDVDVCR
+
K L
M
A
STANDBY/ON button
Sets the component to On or Standby.
Number buttons
B
Used to enter track numbers and times for locating specific points on CD/MD players.
DISC/ALBUM +/– button
C
Selects discs on a CD changer, or the next or previ­ous album on an HDD-compatible component con­nected to an RI Dock.
TOP MENU button
D
Works as a Mode button when used with a DS-A2 RI Dock.
E
Arrow [ ]/[ ] and ENTER buttons
Used to navigate menus on an HDD-compatible component connected to an RI Dock.
F
Playback buttons
From left to right: Pause, Play, Stop, Fast Reverse, Fast Forward, Previous and Next.
G
DISPLAY button
Displays information about the current disc or track on a CD player or MD/CD recorder, including elapsed time, remaining time, total time, and so on. On an HDD-compatible component connected to an RI Dock, it turns on the back light for 30 seconds.
H
CLR button
Cancels functions and clears entered numbers on a CD player or MD/CD recorder.
I
MENU button
Used to navigate menus on an HDD-compatible component connected to an RI Dock.
J
PLAYLIST [ ]/[ ] buttons
Selects the previous or next playlist on an HDD­compatible component connected to an RI Dock.
K
RANDOM button
Used with the random/shuffle playback function.
L
REPEAT button
Used with the repeat playback functions.
M
PLAY MODE button
Used to select play modes on components with selectable play modes. Works as a Resume button when used with a DS-A2 RI Dock.
-
RC
681M
17

Speakers

Subwoofer (SKW-550)

For detailed information, see the pages in parentheses.
Front
1
Rear
(Not North American model)
POWER
ON
OFF
243
To AC outlet
A
STANDBY/ON indicator
Red: Subwoofer in standby mode Green: Subwoofer on
With the Auto Standby function, the SKW-550 automatically turns on when an input signal is detected in Standby mode. When there’s no input signal for a while, the SKW-550 automatically enters Standby mode.
B
OUTPUT LEVEL control (42)
This control is used to adjust the volume of the sub­woofer.
C
LINE INPUT (20)
This RCA input should be connected to the sub­woofer pre out on the AV receiver with supplied RCA cable.
D
POWER switch (Not North American model) (36)
Press this switch to the ON position to turn on the power. Press it to the OFF position to turn off the power.
Note:
The Auto Standby function turns the subwoofer on when the input signal exceeds a certain level. If the Auto Standby function does not work reliably, try slightly increasing or decreasing the subwoofer output level on the AV receiver (page 59).
Attaching and detaching the speaker grilles
Front and Center speakers have detachable grilles. Use the following method to attach or detach the grilles.
1. While holding the bottom edge of the speaker grille with your both hands, pull it gently toward you to remove the bottom of the grille.
2. In the same way, gently pull the upper edge of the speaker grille toward you to remove it from the main unit.
3. To replace the grill, push the projections at the corners into the grille plug holes on the speaker cabinet.
18
ReplacementRemoval

Connecting Your Speakers

Enjoying Home Theater

Thanks to the AV receiver’s superb capabilities, you can enjoy surround sound with a real sense of movement in your own home—just like being in a movie theater or concert hall. You can enjoy DVDs featuring DTS and Dolby Digital. With analog and digital TV, you can enjoy Dolby Pro Logic IIx and Onkyo’s own DSP surround listening modes.
Front left and right speakers (SKF-550F)
These output the overall sound. Their role in a home theater is to provide a solid anchor for the sound image. They should be positioned facing the listener at about ear level, and equally spaced from the TV. Angle them inward slightly so as to create a triangle, with the listener at the apex.
Surround back left and right speakers (SKB-550)
These speakers are necessary to enjoy Dolby Digital EX, DTS-ES
Center speaker (SKC-550C)
This speaker enhances the front left and right speakers, making sound movements distinct and providing a full sound image. For movies it’s used mainly for dialog.
Position it close to your TV facing forward at about ear level, or at the same height as the front left and right speakers.
Subwoofer (SKW-550)
The subwoofer handles the bass sounds of the LFE (Low-Frequency Effects) chan­nel. The volume and quality of the bass output from your subwoofer will depend on its position, the shape of your listening room, and your listening position. In gen­eral, a good bass sound can be obtained by installing the subwoofer in a front cor­ner, or at one-third the way along the wall, as shown.
Tip: To find the best position for your sub­woofer, while playing a movie or some music with good bass, experiment by plac­ing your subwoofer at various positions within the room, and choose the one that provides the most satisfying results.
Corner
1/3 wall length
Matrix, DTS-ES Discrete. They enhance the realism of surround sound and improve sound local­ization behind the listener. Posi­tion them behind the listener about 2–3 feet (60–100 cm) above ear level.
* While speaker set B is on,
these speakers output no sound.
If the subwoofer is placed on a hard floor (wood, vinyl, tile, etc.) and playback is very loud, the subwoofer's feet may damage the flooring. To prevent this, place the supplied pads underneath the sub­woofer's feet. The pads also provide a stable base for the subwoofer.
Surround left and right speakers (SKM-550S)
These speakers are used for precise sound positioning and to add realistic ambience.
Position them at the sides of the listener, or slightly behind, about 2–3 feet (60–100 cm) above ear level. Ideally they should be equally spaced from the listener.
19
Connecting Your Speakers
—Continued

Speaker Connection Precautions

Read the following before connecting your speakers:
•You can connect speakers with an impedance of between 8 and 16 ohms. If you use speakers with a lower impedance, and use the amplifier at high volume levels for a long period of time, the built-in amp pro­tection circuit may be activated.
• Disconnect the power cord from the wall outlet before making any connections.
•Pay close attention to speaker wiring polarity. In other words, connect positive (+) terminals to only positive (+) terminals, and negative (–) terminals to only nega­tive (–) terminals. If you get them the wrong way around, the sound will be out of phase and will sound unnatural.
• Unnecessarily long or very thin speaker cables may affect the sound quality and should be avoided.
• Be careful not to short the positive and negative wires. Doing so may damage the AV receiver.
• Don’t connect more than one cable to each speaker termi­nal. Doing so may damage the AV receiver.
• Don’t connect a speaker to several terminals.

Connecting Speaker Set A

The AV receiver’s positive (+) speaker terminals and speaker’s positive (+) terminals are color-coded for ease of identification. (The negative (–) speaker terminals are all black.) Match the color of each cable to the corre­sponding speaker terminal.
Speaker terminal Color
Front left White
Front right Red
Center Green
Surround left Blue
Surround right Gray
Surround back left Brown
Surround back right Tan
On the AV receiver, unscrew the terminal. Fully
1
insert the bare wires. Make sure that the bare wire is touching the inside of the pole. Screw the termi­nal tight.
On the speakers, while pressing
2
the terminal lever, insert the wire into the hole, and then release the lever.

Using the Speaker Terminal Tool

The supplied speaker terminal tool makes it easy to tighten and loosen the speaker terminals. If you are using banana plugs, to ensure optimum sound quality, tighten the speaker terminal before inserting the banana plug.
Using the supplied RCA cable, connect the AV
3
receiver’s SUBWOOFER PRE OUT to LINE INPUT on the subwoofer.
Make sure the cable is plugged all the way.

Connecting Speaker Set B (sold separately)

Strip 3/8" (10 mm) of insu-
1
lation from the ends of the speaker cables, and twist the bare wires tightly, as shown.
While pressing the lever, insert
2
the wire into the hole, and then release the lever.
Make sure that the terminals are gripping the bare wires, not the insulation.
Note:
When speaker set B is turned on, speaker set A is reduced to 5.1-channel playback.
3/8" (10 mm)
20
Connecting Your Speakers
—Continued
The following illustration shows which speaker should be connected to each pair of terminals.
Speaker Set A (supplied)
Front right
speaker
Center
speaker
Subwoofer
LINE INPUT
Surround
back right
speaker
Surround
back left speaker
Surround
right
speaker
Surround
left
speaker
Front left
speaker
XM
DIGITAL IN
ASSIGNABLE
COAX­IAL
1
(DVD)
2
(CBL/SAT)
OPTICAL
1
(VCR/DVR)
CBL/SAT IN
2
(CD)
REMOTE CONTROL
HDMI
OUT
ASSIGNABLE
IN 1IN 2
Y
V
C
B/PB
S
CR/PR
OUT
VCR/DVR IN
DVD IN
COMPONENT VIDEO
OUT
IN IN
LL
RR
L
R
CD
TAPE
CBL/SAT
INININ
CBL/SAT
SIRIUS
ANTENNA
FMAM75
L
MONITOR
VCR/DVR
DVD
OUT
V
R
S
SURROUND BACK
SURROUND
SPEAKERS
OUT
IN IN
FRONT
SURROUND
OUT
VCR/DVR
SPEAKERS
SURR BACK
CENTER
L
R
SUB
WOOFER
DVD

Wall Mounting

The speakers can easily be mounted on a wall by using the attached wall brackets.
To mount a front, surround, or sur­round back speaker vertically, use its wall bracket, as shown, to hang it on a screw that's securely screwed into the wall.
To mount the center speaker hori­zontally, use its two wall brackets, as shown, to hang it on two screws that are securely screwed into the wall.
L
R
FRONT
CENTER
SPEAKERS A
SPEAKER
PRE OUT
L
SUB
WOOFER
R
FRONT
SPEAKERS B
Front speaker
(SKF-550F)
SURROUND BACK
SPEAKERS
L
R
SURROUND SPEAKERS
Wall brackets
Surround and
Surround back speaker
(SKM-550S/SKB-550)
FRONT
SPEAKERS A
CENTER
SPEAKER
L
R
Front right
speaker
Front left
speaker
Speaker Set B
13" (330 mm)
Center speaker
(SKC-550C)
Caution:
A mounting screw’s ability to support a speaker depends on how well it’s anchored to the wall. If you have hollow walls, screw each mounting screw into a stud. If there are no studs, or the walls are solid, use suitable wall anchors.
Use screws with a head diameter of 5/16" (9 mm) or less and a shank diameter of 1/8" (4 mm) or less. With hollow walls, use a cable/pipe detector to check for any power cables or water pipes before making any holes.
Leave a gap of between 5/16" (7 mm) and 7/16" (10 mm) between the wall and the base of the screw head, as shown.
(We recommend that you consult a home installation professional.)
5/16" – 7/16"
(7 mm) – (10 mm)
Wall
21

Connecting Antennas

This section explains how to connect the supplied indoor FM antenna and AM loop antenna, and how to connect commercially available outdoor FM and AM antennas.
The AV receiver won’t pick up any radio signals without any antenna connected, so you must connect the antenna to use the tuner.
AM antenna push terminals FM antenna jack
OUT
ANTENNA
FMAM75
OUT
OUT
OUT
OUT

Connecting the Indoor FM Antenna

The supplied indoor FM antenna is for indoor use only.
Attach the FM antenna, as shown.
1
American Model
FM 75
Insert the plug fully into the jack.

Connecting the AM Loop Antenna

The supplied indoor AM loop antenna is for indoor use only.
Assemble the AM loop antenna, inserting
1
the tabs into the base, as shown.
Connect both wires of the AM loop
2
antenna to the AM push terminals, as shown.
(The antenna’s wires are not polarity sensitive, so they can be connected either way around).
Make sure that the wires are attached securely and that the push terminals are gripping the bare wires, not the insulation.
Push Insert wire Release
Other Models
FM 75
Insert the plug fully into the jack.
Once your AV receiver is ready for use, you’ll need to tune into an FM radio station and adjust the position of the FM antenna to achieve the best possible reception.
Use thumbtacks or something similar to
2
fix the FM antenna into position.
Thumbtacks, etc.
Caution:
Be careful that you don’t injure yourself
when using thumbtacks.
Once your AV receiver is ready for use, you’ll need to tune into an AM radio station and adjust the position of the AM antenna to achieve the best possible reception.
Keep the antenna as far away as possible from your AV receiver, TV, speaker cables, and power cords.
If you cannot achieve good reception with the supplied indoor AM loop antenna, try using it with a commer­cially available outdoor AM antenna (see page 23).
If you cannot achieve good reception with the supplied indoor FM antenna, try a commercially available out­door FM antenna instead (see page 23).
22
Loading...
+ 50 hidden pages