Onkyo MB-S1 User Manual
Hard Disk Music Library
MB-S1
Contents
Before using 2
Instruction Manual
Thank you for purchasing the Onkyo Hard Disk Music
Library.
Please read this manual thoroughly before making
connections and plugging in the unit. Following the
instructions in this manual will enable you to obtain
optimum performance and listening enjoyment from
your new Hard Disk Music Library. Please retain this
manual for future reference.
Facilities and connections 7
Setup and operation 26
Remote controller 56
Appendix 71
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
Important Safeguards
WARNING
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lightning flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of uninsulated
“dangerous voltage” within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to
alert the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
AVIS
RISQUE DE CHOC ELECTRIQUE
OUVRIR
NE PAS
1. Read Instructions – All the safety and operating instructions
should be read before the appliance is operated.
2. Retain Instructions – The safety and operating instructions
should be retained for future reference.
3. Heed Warnings – All warnings on the appliance and in the
operating instructions should be adhered to.
4. Follow Instructions – All operating and use instructions
should be followed.
5. Cleaning – Unplug the appliance from the wall outlet before
cleaning. The appliance should be cleaned only as recommended by the manufacturer.
6. Attachments – Do not use attachments not recommended by
the appliance manufacturer as they may cause hazards.
7. Water and Moisture– Do not use the appliance near water –
for example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool; and the
like.
8. Accessories – Do not place the appliance on an unstable cart,
stand, tripod, bracket, or table. The appliance may fall, causing
serious injury to a child or adult, and serious damage to the
appliance. Use only with a cart, stand, tripod, bracket, or table
recommended by the manufacturer, or sold with the appliance.
Any mounting of the appliance should follow the
manufacturer’s instructions, and
should use a mounting accessory
recommended by the manufacturer.
9. An appliance and cart combination should be moved with care.
Quick stops, excessive force, and
uneven surfaces may cause the
appliance and cart combination to
overturn.
10. Ventilation – Slots and openings in the cabinet are provided
for ventilation and to ensure reliable operation of the appliance
and to protect it from overheating, and these openings must not
be blocked or covered. The openings should never be blocked
by placing the appliance on a bed, sofa, rug, or other similar
surface. The appliance should not be placed in a builtin installation such as a bookcase or rack unless proper ventilation is provided. There should be free space of at least 5 cm (2 in.) and an
opening behind the appliance.
11. Power Sources – The appliance should be operated only from
the type of power source indicated on the marking label. If you
are not sure of the type of power supply to your home, consult
your appliance dealer or local power company.
12. Grounding or Polarization – The appliance may be equipped
with a polarized alternating current line plug (a plug having one
blade wider than the other). This plug will fit into the power
outlet only one way. This is a safety feature. If you are unable to
insert the plug fully into the outlet, try reversing the plug. If the
plug should still fail to fit, contact your electrician to replace
your obsolete outlet. Do not defeat the safety purpose of the
polarized plug.
PORTABLE CART WARNING
S3125A
2
13. Power-Cord Protection – Powersupply cords should be
routed so that they are not likely to be walked on or pinched by
items placed upon or against them, paying particular attention
to cords at plugs, convenience receptacles, and the point where
they exit from the appliance.
14. Lightning – For added protection for the appliance during a
lightning storm, or when it is left unattended and unused for
long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to
the appliance due to lightning and power-line surges.
15. Overloading – Do not overload wall outlets, extension cords,
or integral convenience receptacles as this can result in a risk of
fire or electric shock.
16. Object and Liquid Entry – Never push objects of any kind
into the appliance through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or
electric shock. Never spill liquid of any kind on the appliance.
17. Servicing – Do not attempt to service the appliance yourself as
opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service
personnel.
18. Damage Requiring Service – Unplug the appliance form the
wall outlet and refer servicing to qualified service personnel
under the following conditions:
A. When the power-supply cord or plug is damaged,
B. If liquid has been spilled, or objects have fallen into the appli-
ance,
C. If the appliance has been exposed to rain or water,
D. If the appliance does not operate normally by following the
operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of
other controls may result in damage and will often require extensive work by a qualified technician to restore the appliance
to its normal operation,
E. If the appliance has been dropped or damaged in any way, and
F. When the appliance exhibits a distinct change in performance
– this indicates a need for service.
19. Replacement Parts – When replacement parts are required, be
sure the service technician has used replacement parts specified
by the manufacturer or have the same characteristics as the
original part. Unauthorized substitutions may result in fire,
electric shock, or other hazards.
20. Safety Check – Upon completion of any service or repairs to
the appliance, ask the service technician to perform safety
checks to determine that the appliance is in proper operation
condition.
21. Wall or Ceiling Mounting – The appliance should be mounted
to a wall or ceiling only as recommended by the manufacturer.
22. Heat – The appliance should be situated away from heat
sources such as radiators, heat registers, stoves, or other appliances (including amplifiers) that produce heat.
23. The apparatus shall not be exposed to dripping or splashing and
that no objects filled with liquids, such as vases shall be placed
on the apparatus.
Precautions
1. Recording Copyright
Recording of copyrighted material for other than personal use is
illegal without permission of the copyright holder.
2. Power
WARNING
BEFORE PLUGGING IN THE UNIT FOR THE FIRST TIME,
READ THE FOLLOWING SECTION CAREFULLY.
The voltage of the available power supply differs according to
country or region. Be sure that the power supply voltage of the area
where this unit will be used meets the required voltage (e.g., AC
230 V, 50 Hz or AC 120 V, 60 Hz) written on the rear panel.
Turning off the standby button does not shut off the power completely. So the power cord should be removed from the AC outlet
when the unit is not used for a prolonged time.
3. Do not touch this unit with wet hands
Do not handle this unit or power cord when your hands are wet or
damp. If water or any other liquid enters the case, take this unit to
an authorized service center for inspection.
4. Location of this unit
Place this unit in a well-ventilated location.
Take special care to provide plenty of ventilation on all sides of this
unit especially when it is placed in an audio rack. If ventilation is
blocked, this unit may overheat and malfunction.
Do not expose this unit to direct sunlight or heating units as this
unit’s internal temperature may rise and shorten the life of the
pickup.
Avoid damp and dusty places and places directly affected by vibrations from the speakers. In particular, avoid placing the unit on or
above one of the speakers.
Be sure this unit is placed in a horizontal position. Never place it on
its side or on a slanted surface as it may malfunction.
Do not place near tuners or TV sets.
If placed next to a TV or tuner, it may cause reception interference
resulting in some noise in the TV or tuner output.
5. Care
From time to time you should wipe the front and rear panels and the
cabinet with a soft cloth. For heavier dirt, dampen a soft cloth in a
weak solution of mild detergent and water, wring it out dry, and
wipe off the dirt. Following this, dry immediately with a clean
cloth.
Do not use rough material, thinners, alcohol or other chemical solvents or cloths since these could damage the finish or remove the
panel lettering.
6. Points to remember
If this unit is brought from a cold environment to a warm one or is
in a cold room that is quickly heated, condensation may form on the
pickup, preventing proper operation. In this case, remove the disc
and leave the power ON for about one hour to remove the condensation.
When transporting this unit, be careful not to bump it.
DANGER:
INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCK FAILED OR DEFEATED. AVOID DIRECT EXPOSURE
TO BEAM.
CAUTION:
THIS PRODUCT UTILIZES A LASER. USE OF CONTROLS
OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES
OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.
For U.S. model
The laser is covered by a housing which prevents exposure during
operation or maintenance. However, this product is classified as a
Laser Product by CDRH (Center for Devices and Radiological
Health) which is a department of the Food and Drug Administration. According to their regulations 21 CFR section 1002.30, all
manufactures who sell Laser Products must maintain records of
written communications between the manufacturer, dealers and
customers concerning radiation safety. If you have any complaints
about instructions or explanations affecting the use of this product,
please feel free to write to the address on the back page of this
manual. When you write us, please include the model number and
serial number of your unit.
In compliance with Federal Regulations, the certification, identification and the period of manufacture are indicated on the rear
panel.
FCC INFORMATION FOR USER
CAUTION:
The user changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to
operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for
help.
Declaration of Conformity
We,
ONKYO EUROPE
ELECTRONICS GmbH
INDUSTRIESTRASSE 20
82110 GERMERING,
GERMANY
declare in own responsibility, that the ONKYO product described
in this instruction manual is in compliance with the corresponding
technical standards such as EN60065, EN55013, EN55020 and
EN61000-3-2, -3-3.
GERMERING, GERMANY
I. MORI
ONKYO EUROPE ELECTRONICS GmbH
Memory Preservation
This unit does not require memory preservation batteries. A
built-in memory power back-up system preserves the contents
of the memory during power failures and even when the unit is
unplugged. The unit must be plugged-in in order to charge the
back-up system.
The memory preservation period after the unit has been unplugged varies depending on climate and placement of the
unit. On the average, memory contents are protected over a
period of a few weeks after the last time the unit was unplugged. This period is shorter when the unit is exposed to a
highly humid climate.
3
Precautions
For Canadian model
NOTE: THIS CLASS B DIGITAL APPARATUS COMPLIES
WITH CANADIAN ICES-003.
For models having a power cord with a polarized plug:
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH
WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
Modele pour les Canadien
REMARQUE: CET APPAREIL NUMÉRIQUE DE LA
CLASSE B EST CONFORME À LA NORME NMB-003 DU
CANADA.
Sur les modèles dont la fiche est polarisée:
ATTENTION: POUR ÉVITER LES CHOCS
ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE
DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA
PRISE ET POUSSER JUSQU’AU FOND.
For European model
This unit contains a semiconductor laser system and is classified as
a “CLASS 1 LASER PRODUCT”. So, to use this model properly,
read this Instruction Manual carefully. In case of any trouble,
please contact the store where you purchased the unit. To prevent
being exposed to the laser beam, do not try to open the enclosure.
“CLASS 1 LAS ER
PRODUCT”
This label on the left hand panel states that:
1. This unit is a CLASS 1 LASER PRODUCT and employs a laser
inside the cabinet.
2. To prevent the laser from being exposed, do not remove the
cover. Refer servicing to qualified personnel.
For British model
Replacement and mounting of an AC plug on the power supply
cord of this unit should be performed only by qualified service personnel.
IMPORTANT
The wires in the mains lead are coloured in accordance with the
following code:
Blue : Neutral
Brown : Live
As the colours of the wires in the mains lead of this apparatus may
not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:
The wire which is coloured blue must be connected to the terminal
which is marked with the letter N or coloured black.
The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.
IMPORTANT
A 5 ampere fuse is fitted in this plug. Should the fuse need to be
replaced, please ensure that the replacement fuse has a rating of 5
amperes and that it is approved by ASTA or BSI to BS1362. Check
for the ASTA mark or the BSI mark on the body of the fuse.
IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE
SOCKET OUTLET IN YOUR HOME, THEN THE FUSE
SHOULD BE REMOVED AND THE PLUG CUT OFF AND DISPOSED OF SAFELY. THERE IS A DANGER OF SEVERE
ELECTRICAL SHOCK IF THE CUT OFF PLUG IS INSERTED
INTO ANY 13 ampere SOCKET.
If in any doubt, please consult a qualified electrician.
4
Contents
Before using
Important Safeguards......................................... 2
Precautions ......................................................... 3
Contents .............................................................. 4
Features ............................................................... 6
Supplied accessories ......................................... 6
Before using this unit ......................................... 7
Setting the Voltage selector (Worldwide models only) ... 7
Installing the remote controller batteries ......................... 7
Using the remote controller.............................................. 7
Facilities and connections
Front panel facilities ........................................... 8
Remote controller ............................................. 10
Rear panel facilities .......................................... 12
Connections ...................................................... 15
Connecting your audio components .............................. 15
Connecting your video components .............................. 16
Connecting speakers ....................................... 19
Ideal speaker configuration ............................................ 19
Minimum speaker configuration for
surround sound playback ........................................ 19
Speaker placement.......................................................... 19
Connecting speakers ....................................................... 20
Connecting the speaker cable......................................... 20
Connecting a subwoofer ................................................. 20
Connecting the remote zone (Zone 2)
speakers ....................................................... 21
When using the ZONE 2 OUT terminals ...................... 21
Operating components not reached by the
remote controller signals (IR IN/OUT) ....... 22
If the remote controller signal does not reach
the TX-DS797 remote sensor ................................. 22
If the remote controller signal does not reach
other components .................................................... 22
Connecting the power ...................................... 23
Connecting antennas ....................................... 24
Assembling the AM loop antenna.................................. 24
Connecting the AM antenna cable ................................. 24
Connecting the included antennas ................................. 24
Connecting an FM outdoor antenna............................... 25
Connecting an AM outdoor antenna .............................. 25
Directional linkage ......................................................... 25
Connecting the antenna cable to the 75/300 Ω antenna adapter
(For all models other than European models) .............. 25
Setup and operation
Setup menus ..................................................... 26
Navigating through the Setup menu .............................. 27
Hardware Setup................................................. 28
0. Hardware Setup menu ............................................. 28
0-1. Speaker Impedance sub-menu ................................ 28
0-2. IR IN Setup sub-menu ............................................ 28
0-3. AM Frequency Step sub-menu ............................... 28
Speaker Setup ................................................... 29
1. Speaker Setup menu................................................. 29
1-1. Speaker Config sub-menu ...................................... 29
1-2. Speaker Distance sub-menu.................................... 30
1-3. Level Calibration sub-menu ................................... 31
1-4. Bass Peak Level (Bass Peak Level Manager*)
sub-menu ................................................................. 32
Input Setup ........................................................ 33
2. Input Setup menu ..................................................... 33
2-1. Digital Setup sub-menu .......................................... 33
2-2. Multichannel Setup sub-menu ................................ 34
2-3. Video Setup sub-menu ............................................ 35
2-4. Character Input sub-menu ...................................... 36
2-5. Intelli Volume sub-menu ......................................... 36
2-6. Listening Mode Preset sub-menu ........................... 37
Audio Adjust...................................................... 40
3. Audio Adjust Setup menu ........................................ 40
Preference ......................................................... 44
4. Preference menu ....................................................... 44
4-1. Volume Setup sub-menu ......................................... 44
4-2. Headphones Level Setup sub-menu ....................... 45
4-3. OSD Setup sub-menu.............................................. 45
4-4. OSD Position sub-menu ......................................... 45
Listening to Radio Broadcasts........................ 46
Tuning into a radio station ............................................. 46
Listening to a stereo radio station (FM mode) .............. 46
Presetting a radio station ................................................ 47
Selecting a preset radio station ...................................... 47
Erasing a preset radio station ......................................... 47
Listening to RDS broadcasts
(European models only).............................. 48
Listening to RDS broadcasts .......................................... 48
PTY program types in Europe........................................ 48
Displaying Radio Text (RT) ........................................... 49
Performing a PTY scan .................................................. 49
Performing a TP scan ..................................................... 49
5
Main Features
■ Encoding the music files on an audio CD in
(*1)
MP3 format
and decoding the MP3 music
files
• You can record tracks on an audio CD in MP3 format. The
tracks are compressed approximately 1/10 in data size
when using the standard 128kbps bitrate
(*2)
.
• Available encoding bitrates are no compression (PCM),
96kbps, 128kbps, and 192kbps.
• You can display and edit the ID3 tag(*3) information
including song title, album title and artist name.
• You can record from the built-in CD player, digital input
and analog input. In addition, you can record (transfer) the
tracks stored on PC through USB interface.
• Sorting feature using the file information including ID3
tags is available for various playback modes.
• You can mark any tracks you like as your favorites and
play only the favorite tracks.
■ Playing audio CDs and CD-Rs
• You can play CD-Rs containing audio data in MP3 format
as well as ordinary audio CDs.
• You can copy the MP3 files recorded on a CD-R to the
internal hard disk drive (HDD) 10 times faster than when
recording tracks from an audio CD (when using the
QUICK REC feature).
*1 MP3
An audio compression format that is part of MPEG1 image
compression technology.
*2 bitrate
The maximum amount of data that can be processed by a system per
second.
Bit is the minimum unit for showing 0 and 1 in digital data.
kbps is the abbreviation of kilo bit per second. The larger the bitrate
is used, the greater the encoded file size is.
3
*
ID3 tag
The area for storing character information on MP3 file.
You can add up to 128 bytes of character information such as album
title and artist name. Each information will be limited to 30
characters long. The information entered in the ID3 tag area can be
displayed and edited on the player which supports ID3 tag.
■ Longer hours recording with the internal
hard disk drive (HDD)
• FDB (Fluid Dynamic Bearing) motor employed in the
HDD section has the lowest vibration characteristics
suited for audio device with motor. This enables stability
in playback.
• You can record and play MP3 music files many hours
using the HDD. More than 350 hours of music can be
recorded onto the 20GB HDD when using standard
128kbps bitrate.
• Timer recording feature allows you to record long hour
programs away from the MB-S1.
■ Transferring music files from PC to the
MB-S1
• The MP3 files stored on PC can be transferred to the MBS1 through USB interface using the Carry Tunes (attached
file transfer software).
6
Supplied accessories
Check that the following accessories are supplied with the MB-S1.
Audio connection cables × 2Remote controller × 1
Batteries (AA, R6 or UM-3) × 2
CD-ROM × 1 USB cable × 1
Before using this unit
Installing the remote controller batteries
1. Remove the battery compartment cover by pressing
and sliding the cover.
2. Insert two AA (R6 or UM-3) batteries into the battery
compartment. Carefully follow the polarity diagram
(positive (+) and negative (–) symbols) inside the
battery compartment.
cable × 1
Instruction manual × 1
Warranty card × 1
Using the remote controller
Point the remote controller toward the remote control sensor. The
STANDBY indicator lights up when the unit receives a signal from
the remote controller.
Remote control sensor
MB-S1
3. After batteries are installed and seated correctly,
replace the compartment cover.
Notes:
• Do not mix new batteries with old batteries or different kinds of
batteries.
• To avoid corrosion, remove the batteries if the remote controller
is not to be used for a long time.
• Remove dead batteries immediately to avoid damage from
corrosion. If the remote controller does not operate smoothly,
replace both the batteries at the same time.
• The life of the batteries supplied is about six months but this will
vary depending on usage.
6
STANDBY indicator
30˚
30˚
Approx. 16 feet
(5 meters)
Notes:
• Place the unit away from strong light such as direct sunlight or
inverted fluorescent light which can prevent proper operation of
the remote controller.
• Using another remote controller of the same type in the same
room or using the unit near equipment which uses infrared rays
may cause operational interference.
• Do not put objects on the remote controller. Its buttons may be
pressed by mistake and drain the batteries.
• Make sure the audio rack doors do not have colored glass.
Placing the unit behind such doors may prevent proper remote
controller operation.
• If there is any obstacle between the remote controller and the
remote control sensor, the remote controller will not operate.
Parts names and functions
Front panel
The numbers within the brackets are the pages where the part or function is introduced.
1
STANDBY/ON
ON
STANDBY
USB
K
DISPLAY CD DUBBINGTEXT HDD REC REC MODE
IHG FEDC B A 0 9
J
FAVORITE IT
EXTERNAL INPUT
3
PLAY MODE
MENU/EXIT
C D HDD
4
MULTI JOG
PUSH TO ENTER
OPERATION
5
62
EDIT/CLEAR
NOYES
PLAY LIST
HARD DISK MUSIC LIBRARY
STOP PLAY PAUSE
/
MB-S
8
7
1
1
STANDBY/ON button [xx]
Turns on the MB-S1 or lets it enter the standby state.
2
MENU/EXIT button [xx]
Switches the menu mode. Press this button while selecting any
menu item exits the menu.
3
PLAY MODE/YES button [xx]
Switches play mode combined with use of the jog dial.
4
MULTI JOG dial
Usually, used for selecting the group number (folder). While setting
any mode, used for selecting the parameters for a mode. Also, press
this dial to confirm the entry.
5
EDIT/CLEAR/NO button [xx]
Press this button to enter the state for setting modes or parameters.
When you are asked to select Yes or No, this button works as NO
selection. While editing ID3 tag information, this button works as
CLEAR button for canceling the entry.
6
PLAY LIST button [xx]
Switches the play lists combined with use of the jog dial. You can
store up to 100 play lists on memory of the MB-S1.
7
STOP
button [xx]
Stops the playback of CD or HDD.
8
PLAY PAUSE
/
button [xx]
Starts playing or recording tracks on CD or HDD.
Press this button while playing or recording, the MB-S1 pauses.
Press it again resumes playing or recording.
9
button [xx]
Press to locate the beginning of the next track. Hold down to fast
forward.
10
button [xx]
Press to locate the beginning of the current or previous track. Hold
down to rewind.
11
HDD button [xx]
Activates the HDD section.
12
CD button [xx]
Activates the CD player section.
13
EXTERNAL INPUT [xx]
Selects the external input source.
The input sources switches in the order of DIGITAL-1 (optical),
DIGITAL-2 (coaxial), and ANALOG.
14
REC MODE button [xx]
Switches recording mode.
The recording modes switch in the order of PCM, MP3 96Kbps,
MP3 128Kbps, and MP3 192Kbps.
15
HDD REC button [xx]
Puts the MB-S1 in recording standby state. Press it again to select a
group which the recorded tracks will belong to.
16
FAVORITE IT button [xx]
Marks the currently selected or played track as your favorite.
Pressing the button again unmarks the track.
17
CD DUBBING button [xx]
Copies whole CD onto the MB-S1's HDD with ease.
18
TEXT button [xx]
Enters the mode for entering and editing characters.
19
DISPLAY button [xx]
Switches the information displayed in the display area (TITLE,
ALBUM, ARTIST, GENRE, DATE, GROUP). Displays the letter
you entered while editing information.
20
(open/close) button [xx]
Opens and closes the CD tray.
21
USB port [xx]
Connects the PC. You can transfer MP3 audio files from a PC to the
MB-S1’s HDD using the Carry Tunes PC software.
The MB-S1 supports the hot plug capability, allowing you to
7
connect or disconnect without turning the PC off.
Parts names and functions
Front panel display
The numbers within the brackets are the pages where the part or function is introduced.
1
2 4 5 6 7
3
8
9
1
PLAY MODE indicators [xx]
The indicator showing current play mode lights.
2
FAVORITE indicator [xx]
Lights while your favorite tracks are played.
3
ALL indicator [xx]
Lights when the all tracks are played regardless of the play mode.
4
CD mode indicator [xx]
Lights when you are playing CD.
5
HDD mode indicator [xx]
Lights when you are playing tracks recorded on the hard disk drive.
“QUICK” lights when the quick recording (copying tracks) mode is
operating. “MP3” lights when the tracks are recorded in MP3
format.
6
DIGITAL 1 2, ANALOG indicators [xx]
Lights when the DIGITAL 1 (optical), DIGITAL 2 (coaxial), or
ANALOG (analog) is selected for input source.
7
NAVI indicator [xx]
Lights when the display shows the current position of the track
played.
FA0 B C D E
11
REPEAT/REPEAT 1 indicator [xx]
Lights when the tracks are played repeatedly. “REPEAT 1” lights
when the single track is played repeatedly.
12
RANDOM indicator [xx]
Lights when the tracks on the hard disk drive are played in random
order.
13
T.PLAY and T.REC indicators [xx]
Lights when the timer recording or playing operation is reserved.
14
TOTAL, SINGLE, and REMAIN indicators [xx]
Lights when the playing time information is shown in the versatile
area.
15
MP3, PCM, 96, 128, and 192 indicators [xx]
Shows the encode mode for the current track. When you play the
MP3 track, “MP3” indicator lights with “96”, “128”, or “192”
indicator according to the track's bitrate. When any other bitrate is
used for the MP3 track, only “MP3” indicator lights.
16
Level indicator [xx]
Shows the audio level for the current track or the position currently
playing.
8
PLAY LIST indicator [xx]
Lights when the tracks registered with the play list are played.
9
TITLE, ALBUM, ARTIST, GENRE, and
DATE indicators [xx]
Shows the display mode for the versatile area.
10
Multi function display
8
Parts names and functions
Remote controller
The numbers within the brackets are the pages where the part or function is introduced.
1
36
8
7
0
B
E
G
I
J
45 2
9
A
D
C
F
H
K
L
6
DISPLAY button [xx]
Press to change the display mode.
7
CLOCK button [xx]
Press to display the current day of the week and time.
8
EXT INPUT button [xx]
Press to select the input source.
With each press of the button, the input source switches in the order
of DIGITAL 1, DIGITAL 2, and ANALOG.
9
OPERATION buttons [xx]
CD: Turns the operation mode into the CD mode.
HDD: Turns the operation mode into the HDD mode.
10
HDD REC button [xx]
Press to enter the recording standby state. Then press again to select
the target recording group.
11
REC MODE button [xx]
Press to select the recording mode.
With each press of the button, the recording mode switches in the
order of PCM, MP3 96Kbps, MP3 128Kbps, and MP3 192Kbps.
M
1
ON button [xx]
Press to turn the MB-S1 on and off.
2
STANDBY button [xx]
Press to turn the MB-S1 into the standby state.
3
DIMMER button [xx]
Press to change the brightness of the display.
4
COUNTER button [xx]
Press to change the displayed information for playing time.
5
SCROLL button [xx]
Press to scroll the display.
12
Press to start playing or recording. Pressing this button while
playing or recording, the MB-S1 pauses. Press the button again to
resume playing or recording.
13
Press to stop playing or recording.
14
While playing, press to jump to beginning of the current track and
the next track respectively. While stopped, press to select the track
you want to play.
15
When you want to play tracks in random order, press this button to
set the random play. The “RANDOM ON” lights in the display
area.
16
When you want to play a track or tracks repeatedly, use this button
to select the repeat playback mode.
17
Press to switch the playback mode.
ALBUM: Displays the album information.
ARTISTS: Displays the artist information.
GENRE: Displays the genre information.
DATE: Displays the date information.
GROUP: Displays the group information.
PLAYLIST: Displays the play list information.
/
(play/pause) button [xx]
(stop) button [xx]
/ button [xx]
RANDOM button [xx]
REPEAT button [xx]
PLAY MODE button [xx]
9
Parts names and functions
The numbers within the brackets are the pages where the part or function is introduced.
18
ADD TO PLAY LIST button [xx]
Press to add the current track to the play list.
21
FAVORITE IT button [xx]
Press to mark the current track as your favorite. Press again to
unmark the track.
19
SELECT button [xx]
Select the track using
/ buttons.
22
FAVORITE MODE button [xx]
Press to turn the favorite mode on and off. In the favorite mode,
20
Alphabetic letters/Symbols/Numeric (1 to 10)
only the tracks marked as your favorite are played.
buttons [xx]
23
Numeric: Press to select the track you want to play.
Alphabetic letters/SYMBOL/Numeric: Press to enter the name
of the disk, artist or track.
Genre buttons [xx]
Press to select the genre for playing the tracks registered with
respective genres.
CLEAR: Press to cancel the letter.
ENTER: Press to enter and confirm the letter while editing the
disc, artist, or track names.
TEXT: Press to enable editing the disc, artists, or track names.
Rear panel
The numbers within the brackets are the pages where the part or function is introduced.
DIGITAL
DIGITAL
INPUT
L
R
INPUT
ANALOG
OUTPUT
L
R
OPTICAL
OUTPUT
HARD DISK MUSIC LIBRARY
MODEL NO.
MB-S
2
1
OPTICAL
COAXIAL
REMOTE CONTROL
1
12 4
1
Analog input/output terminals (ANALOG) [xx]
3
Connect the analog devices such as tuner or cassette deck, and the
analog output from the digital devices such as CD player and others.
2
Digital input terminals (DIGITAL INPUT) [xx]
Connect the digital output from the digital devices such as CD
player, DVD player, MD player and others. Optical (OPTICAL)
and coaxial (COAXIAL) terminals are available.
3
connection terminals ( REMOTE CONTROL)
[xx]
Connect the Onkyo products equipped with the connection
terminals.
10
4
Digital output terminal (DIGITAL OUTPUT) [xx]
Connects the digital output from the MB-S1 to the digital input
terminals on the digital recording devices such as MD recorder, CD
recorder and DAT deck.
Under the SCMS and SDMI Water Mark* copyright protection
system, the output signal is limited to the AUDIO-CD signal from
the CD-ROM played or the audio signal of MP3 data recorded on
CD-ROM.
Note
The audio signal recorded on the MB-S1's hard disk drive is not
output digitally.
* SCMS and SDMI are a copy guard system for protecting
copyright. See page 17 for details.
Connecting the MB-S1
Here is an explanation of how to connect the main components to
the MB-S1 in the standard manner. There are many ways that any
one component can be connected, and it is up to you to decide
which method best fits your situation. The directions given here are
only one option and should only be thought of as such. It is best to
fully understand the nature of each connector and terminal as well
as each of your components and their features to ascertain which
method of connection is best.
• Be sure to always refer to the instructions that came with
the component that you are connecting.
• Do not plug in the power cord until all connections have
been made.
• For input jacks, red connectors (marked R) are used for the
right channel, and white connectors (marked L) are used for
the left channel.
• Do not bind audio/video connection cables with power cords
and speaker cables. Doing so may adversely affect the
picture and sound quality.
• When using the digital inputs, make sure to also connect the
analog connections whenever possible.
DIGITAL
DIGITAL
INPUT
OPTICAL
OUTPUT
2
1
OPTICALCOAXIAL
REMOTE CONTROL
L
L
R
R
OUTPUT
INPUT
ANALOG
• Insert all plugs and connectors securely. Improper
connections can result in noise, poor performance, or
damage to the equipment.
Improper connection
Inserted completely
• When using one of the optical input jacks, remove the
protective cap and keep it safely. When the jack is not used,
replace the protective cap.
• When using an optical input jack, always use an optical
fiber cable.
Optical digital input terminal
An optical digital input terminal is equipped
with a protection cap. When connecting, remove
this cap. When not using, put the cap back on
the terminal.
HARD DISK MUSIC LIBRARY
MODEL NO.
MB-S
1
LRR L
6
Audio
connection
cable
1 2
LRLR
Analog
output
Analog
input
terminall Analog output Digital
4 3
LR
Amplifier Tuner, cassette tape CD/DVD/MD CD/MD recorder
cable
Coaxial
digital cable
output
Optical digital cable
:
Signal flow
Digital input
5
11
Connecting the MB-S1
Connecting to other components
Here is detailed explanation of how to connect the main
components to the MB-S1. When connecting, refer to the diagram
on page 14.
1. Connecting to an amplifier
Connect the analog terminals on the MB-S1 to the CD, TAPE, or
MD terminal on the amplifier.
Notice:
When you connect the MB-S1 to the Onkyo TX-L5, use the HD
terminal on the rear panel of the TX-L5
2. Connecting an external CD or DVD
player
When connecting a CD player, DVD player, CS tuner, or DAT deck
equipped with digital output terminals (OPTICAL/COAXIAL), you
can record the input source digitally using the MB-S1.
Connect the digital output terminals on a CD player, DVD player or
others to the DIGITAL INPUT (OPTICAL/COAXIAL) terminals
using audio digital cables. Use the optical digital cable for
OPTICAL terminal and the coaxial digital cable for COAXIAL
terminal.
When connecting devices, be sure to use the optical digital cable
commercially available.
4. Connecting an analog audio device
such as AM/FM tuner or cassette tape
deck
When connecting the audio output from an analog audio device
such as AM/FM tuner, cassette tape deck, or video deck to the MBS1, you can record the audio signal onto the HDD.
Connect the analog output terminals on the analog audio device to
the ANALOG INPUT terminal on the MB-S1.
Notes:
• Insert the plugs and connectors securely. Remember that
improper connection can result in noise, or malfunctions.
• Do not bundle the audio cables together with power cords or
speaker cables. Doing so may cause deterioration of the audio
signal.
• When you place the MB-S1 near a TV, the picture on the TV
may become poor and the output sound from the MB-S1 may be
distorted. In this case, place the unit away from the TV.
5. Connecting the power cord
Plug the power cord into a wall outlet.
White line
Wall outlet
3. Connecting a digital audio recorder
such as MD recorder or CD recorder
When connecting a CD recorder, MD recorder or DAT deck
equipped with digital input terminals (OPTICAL), you can perform
digital recording on the external digital audio recorder.
Connect the DIGITAL OUTPUT terminal (OPTCAL) on the MBS1 to the digital audio recorder such as CD recorder or MD
recorder. Use an optical digital audio cable.
When connecting devices, be sure to use an optical digital cable
commercially available.
Notes
• When you copy the audio source digitally, certain restrictions
will be applied. (page 14)
• Do not bundle the audio cables together with power cords or
speaker cables. Doing so may cause deterioration of the audio
signal.
• When you place the MB-S1 near a TV, the picture on the TV
may become poor and the output sound from the MB-S1 may be
distorted. In this case, place the unit away from the TV.
• When you connect the digital audio output on a DVD player to
the DIGITAL INPUT terminals on the MB-S1, set the output
type to PCM on the DVD player.
However, the PCM output setting is not available on some DVD
players. In this case, the audio signal will not be output even if
the DVD player and the MB-S1 are connected.
Longer slit
Note:
For better sound quality
The power cable of the MB-S1 has polarity.
Insert the plug matching the side with white line to the longer slit on
the wall outlet.
After connecting the power cable, the MB-S1 enters the standby
state.
PLAY MODE
EXTERNAL INPUT
MULTI JOG
MENU/EXIT
PUSH TO ENTER
OPERATION
C DHDD
EDIT/CLEAR
NOYES
PLAY LIST
HARD DISK MUSIC LIBRARY
STOP PLAY PAUSE
/
MB-S
1
STANDBY/ON
ON
STANDBY
USB
“STANDBY”
indication lights.
DISPLAY CD DUBBINGTEXT HDD REC REC MODE
FAVORITE IT
The date indication
blinks.
6. Connecting the Onkyo products
equipped with terminals
With Onkyo components that are equipped with a terminal, use
the supplied RI cable to connect the
of the MB-S1.
The
terminals are only effective if they are used in conjunction
with an Onkyo amplifier with a
component other than an Onkyo component with a
Doing so may damage the BB-S1.
The functions of the left and right terminals are the same.
Connect to either one.
Connecting the cable only does not make the system
operational. You must also connect the audio cables as well.
terminal to the terminal
connector. Do not connect to a
connector.
12
Notes on CD and the internal hard disk drive
Notes on discs
■ Notes on playing discs
Use the discs compatible with IEC standards such as the
CD with the logo (right) printed on it. You can also use
the CD-ROM containing MP3 audio data.
Do not play CD-ROMs intended for computer use or non-audio
compact discs. Doing so may cause high-pitched noises or other
unpredictable results that may damage speakers, amplifiers, and
other connected components.
Never use heart-shaped, octagonal, or other special shaped discs as
they may damage the internal mechanisms of the MB-S1.
■ Handling discs
Be careful not to touch the data side of the disc (the side that does
not have printing on it). Always hold discs by the edges or by using
the hole in the middle.
■ Cautions for disc storage
Do not store discs in locations exposed to direct sunlight, near heat
emitting devices, and other locations of excessive heat, or locations
of extremely low temperatures. Also, always store discs properly in
their protective cases.
Note on the internal hard disc drive
■ Do not shake or carry around the MB-S1
while playing the tracks recorded on the
hard disc drive. Doing so may damage
the internal hard disk drive.
Never place labels or stickers on the data side or label side of the
discs. Also, do not write on the discs or allow them to become
scratched.
■ Cautions when using rented compact
discs
Do not use discs that have cellophane tape attached to them or
rental compact discs that have rental labels attached. If the tape is
sticking out or peeling off, the disc may not be able to be ejected
and the MB-S1 may become damaged.
■ Cleaning
Dirt and contaminants on discs can obstruct the pickup of the
signals and lead to deterioration the sound. When dirty, clean the
data side with a soft dry cloth, wiping from the inside of the disc
toward the outside.
If the dirt is excessive, soak the cloth in water, wring it out, and
then wipe the disc surface clean. Next, using a soft dry cloth, wipe
the moisture form the disc surface. Do not use conventional record
cleaners or antistatic agents. Also, never use benzene, thinners, or
other volatile agents as they may damage the disc surface.
Condensation
When moving the MB-S1 from a cold location to a hot location,
when quickly heating a cold location with a furnace, or other
similar situation, condensation may occur. This may not only
cause improper operation of the device, but may also damage
the discs and components. If condensation has occurred, turn on
the MB-S1 and leave it running for 1 to 2 hours. If you will not
use the MB-S1, then eject any disc inside.
13
Rules for recording digital input
The digital source connected to the MB-S1 is protected by copy
guard systems.
These limitations are intended for protecting the copyright and
restricting the behavior which violates the copyright.
SCMS (Guide to the serial copy management system)
This system is designed for permitting only one generation of digitalto-digital copying (the recording of the original digital signals as they
are) between digital audio devices.
• The digital signals recorded on MD, DAT, CD-R, or CDRW from the digital output terminals on the MB-S1 cannot
be recorded on any other media digitally. Here are the
examples when performing digital recording in MD
recorder.
1. When the digital audio data from the MB-S1 is recorded as
analog input source on a MD using MD recorder, the digital
signal on the MD can be recorded digitally onto another MD.
MB-S1
Analog input recording
❍ Digital input recording
❍ Analog input recording
MD recorder
MD
MD player MD recorder
• The digital audio source recorded on a media such as CD,
MD or DAT can be connected directly to the digital input
terminals on the MB-S1.
However, if the input digital signal to the MB-S1 was
digitally recorded from the digital source, you can not
record this digital input signal. Also, you can not monitor
this digital input signal as a digital input source.
1. The digital audio signal on CD-R/RW recorded digitally from
the CD can not be copied to the MB-S1’s HDD. When you
record such digital signals, connect the signals to the analog
input terminals.
CD player CD recorder
Digital input recording
CD-R
HDD CD
MB-S1
✕ Digital input recording
❍ Analog input recording
2. When the digital audio signal on CD was recorded from MD as
analog input source, you can record the audio signal on CD
digitally from digital input terminals on the MB-S1.
2. When the digital audio data from the MB-S1 is recorded as
digital input source on a MD using MD recorder, the digital
signal on the MD cannot be recorded digitally onto another MD.
If you want to record the digital signal on the MD, perform
analog input recording.
MB-S1
Digital input recording
✕ Digital input recording
❍ Analog input recording
MD recorder
MD
MD playerMD recorder
Note:
For media or music performance including radio program, CD, record,
music tape, and original music cassette, music elements of lyrics and
melodies are equally protected by the copyright law. Therefore, to sell,
transfer, distribute, and lease those music media above, and use them
as BGM in public space such as stores are prohibited.
CD player MD recorder
Analog input recording
MD
MD playerMB-S1
❍ Digital input recording
❍ Analog input recording
SDMI (Secure Digital Music Initiative) WM
The MB-S1 supports the data with the Water Mark which conforms
to the SDMI standards.
This water mark is designed for copy control, and some discs
contains the water mark can not be duplicated.
SDMI is a project for establishing formats which allows secure
music distribution and sales over Internet. The project is co-founded
by RIAA and five companies from U.S. music industry.
The materials you recorded using the MB-S1 are for private use
only. Under the copyright law, you can not use recorded materials
without permission from the copyright holder.
14
Understanding the basic operations before
using the MB-S1
The MB-S1 allows you to play audio CDs or CD-R discs containing
MP3 music files just like ordinary CD players. In addition, the MBS1 can store the music data on its hard disk drive (HDD), allowing
you to enjoy the various playback functions such as long-hour
playback or play list playback.
■ Managing the music information on the
MB-S1
The MB-S1 manages the music information in groups and tracks.
The number of group and track is shown on the display when the
“GROUP” indicator lights.
When using the MB-S1 for playing CDs, only the number of group
and track is displayed and you can select the tracks according to the
group or the track number. When using or playing the tracks
recorded on the MB-S1’s HDD, the various music information is
available, including the name of album and artist, genre, date, and
favorite marking, as well as the number of group and track.
Registering additional track information enables you to sort the
track, play only the favorite tracks, display the tracks information
and select the track according to the track information.
■ Typical uses for the MB-S1
1. Playing an audio CD with the CD player section.
For more information, see “Understanding playing features for
the CD player section” on this page and “Listening to an audio
CD or CD-ROM” on pages 19 and 20.
6. Playing tracks on the HDD using a play list.
For more information, see “Understanding playing features for
the internal HDD section” on this page, “Understanding the play
list” on the next page, “Listening to tracks recorded on the
HDD” on pages 25 and 26, and creating and using a play list on
pages 31-37.
■ Understanding playing features for the
CD player section
The CD player section of the MB-S1 allows you to play audio CDs and
CD-R discs containing music files encoded in PCM or MP3 format.
You can select and play the track by the group or the track number.
Use the MULTI JOG dial to select a group and the
to select a track number.
• When playing an audio CD
One CD = One group/
The total tracks on the CD = The number of tracks
The number of tracks
• When playing a CD-R containing MP3 files
The number of folders on the CD-R = The group number/
The number of files in each folder = The number of tracks
/ buttons
2. Playing a CD-R containing MP3 music files with the
CD player section.
For more information, see “Understanding playing features for
the CD player section” on this page and “Listening to an audio
CD or CD-ROM” on pages 19 and 20.
3. Recording tracks from the CD player section onto the
internal HDD and playing them.
For more information, see “Understanding playing features for
the internal HDD section” on this page, and “Recording” and
“Listening to tracks recorded on the HDD” on pages 21-26.
4. Recording tracks from the external component such
as MD player to the HDD and playing them.
For more information, see “Understanding playing features for
the internal HDD section” on this page, “Connecting the MBS1” on page 16, and “Recording” and “Listening to tracks
recorded on the HDD” on pages 21-26.
5. Transferring MP3 files from the PC to the MB-S1 and
playing them.
For more information, see “Understanding playing features for
the internal HDD section” on this page, “Listening to tracks
recorded on the HDD” on pages 25 and 26, and “Overview of
the supplied Carry Tunes software” on page 45.
The number of groups
* Sorting track order, random playback, and MP3 file tag
information is not available for the CD player section. If you
want to use these features, the tracks on CD or CD-R are
required to be recorded onto the internal HDD.
The number of tracks
■ Understanding playing features for the
internal HDD section
In the HDD section of the MB-S1, you can record the input source
from the CD player section and the external component such as MD
player, and transfer the tracks from PC to the MB-S1 and play them.
* For the tracks not containing the album title, artist name, genre,
date or favorite marking, you cannot use the sort feature with
the ALBUM, ARTIST, GENRE or DATE button and the
favorite track playback feature. In this case, the tracks will be
sorted and played by group and the track number.
* When you create or edit the play list, you select the tracks by
group and track number. For more information on play list, see
“Understanding Play List.”
15
Understanding the basic operations before using the MB-S1
Playlist 1
Group No.
1
Track No.
13
2
32
3
54
■ Understanding the play list
You can create a play list compiled by choosing your favorite tracks
from those on the HDD. You can also name the play list and easily
switch the play list when playing.
The track information registered in the play list is just a reference to
the actual track information stored on the HDD. Therefore, editing
or deleting a play list will not change or delete the track information
stored on the HDD. If the track in a play list contains additional
information such as album title and others, the additional
information will be displayed when selecting or playing tracks.
For more information on creating and using a play list, see pages
31-37.
* You can create up to 100 play lists.
Each track can contain following
information used for playback
and display.
• Track Title
• Album Title
• Artist Name
• Genre
• Date
• Favorite Marking
The MB-S1 will seach a track on the
play list through the HDD in the order
defined in the list and play the found
track.
Playlist 2
Playlist 3
Playlist 4
Track 1
Track 2
Track 3
HDD
Group 1 Group 2
Group 3
Track 1
Track 2
Track 3
16
MB-S1
Understanding the basic operations before
OPERATION
C D HDD
ON
STANDBY
USB
HARD DISK MUSIC LIBRARY
MB-S
1
OPERATION
MULTI JOG
PLAY MODE
MENU/EXIT
PUSH TO ENTER
PLAY LIST
EDIT/CLEAR
NOYES
STANDBY/ON
STOP PLAY PAUSE
/
DISPLAY CD DUBBINGTEXT HDD REC REC MODE
EXTERNAL INPUT
FAVORITE IT
C D HDD
using the MB-S1
STANDBY/ON button
(open/close) button
OPERATION buttons
Turning on the power
Press the STANDBY/ON button on the MB-S1 to turn on the
power. Pressing it again causes the MB-S1 to enter the standby
state. When using the remote controller, pressing the ON button
turns on the power and pressing the STANDBY button causes the
MB-S1 to enter the standby state.
STANDBY / ON STANDBY / ON
ON
STANDBY
ON
STANDBY
Remote controller
ON button
STANDBY button
OPERATION
buttons
Switching the CD player and HDD
The MB-S1 can play the tracks on an audio CD or a CD-ROM
containing music files as well as the tracks recorded on the hard
disk drive (HDD). To switch the playing source, use the
OPERATION buttons.
Pressing the CD button activates the CD player, and the MB-S1
STOP
enters the CD mode. The CD,
, and
indicators light in orange. In the CD mode, you can play audio CDs
and CD-ROM discs using the buttons on the MB-S1 or remote
controller.
OPERATION
C D HDD
Remote controller
PLAY PAUSE
/
Standby state: The state that the current time is displayed in the
display area. If you have not set the current time, “-- : --” is
displayed (see the next page).
Power-on state: The state that the STANDBY/ON button on the
MB-S1 or the ON button on the remote controller is pressed during
the standby state. In the power-on state, you can operate the MBS1. After pressing the button, “HDD MUSIC LIBRARY”
indication scrolls in the display area. Then, the number of groups
and the total recorded time for tracks on the HDD is displayed, and
the same mode indicators lights as when the MB-S1 turned on last
time. When the CD mode is active, “Reading Media” is displayed
in the display area and loading CD starts. After the CD loading
process has finished, the number of groups and tracks, and the total
recorded time for the CD.
When the HDD section is activated, the same group indication
lights as when the MB-S1 turned on last time.
Pressing the HDD button activates the HDD section, and the MBS1 enters the HDD mode. The HDD,
PLAY PAUSE
/
indicators light in green. In the HDD mode,
STOP
, and
you can play the music files recorded on the internal HDD.
Remote controller
Opening the CD tray
Press (open/close) button on the MB-S1 to
open the CD tray.
Note:
For few seconds immediately after the power is turned on, pressing
any button will do nothing. Remember to operate the MB-S1 after
the loaded information is displayed.
17
Setting date and time
YES button
STANDBY/ON
ON
STANDBY
USB
DISPLAY CD DUBBINGTEXT HDD REC REC MODE
FAVORITE IT
MULTI JOG dial
EDIT/CLEAR
EXTERNAL INPUT
PLAY MODE
MENU/EXIT
MULTI JOG
PUSH TO ENTER
OPERATION
C D HDD
NOYES
PLAY LIST
HARD DISK MUSIC LIBRARY
STOP PLAY PAUSE
/
MB-S
1
CLOCK button
DISPLAY button
Setting date and time
1. Call the menu mode.
MENU/EXIT
Pressing the MENU/EXIT button displays the
menu items in the display area.
2. Select the clock setting menu.
MULTI JOG
PUSH TO ENTER
MULTI JOG
Rotate the MULTI JOG dial to select the clock
setting menu (“Clock Setting?”).
The menu items are displayed in the following
order: Clock Setting?, Timer Setting?, REC
LEVEL?.
Press the MULTI JOG dial.
MENU button
buttons
/
Set the month, day, hour and minute using the
same procedure above.
The day of the week will be automatically set.
You can highlight any item (year, month, day,
hour, and minute) to set them using the
/ buttons.
3. Confirm the setting.
PLAY MODE
YES
Press the YES button to confirm the setting. The
second is displayed and the clock starts.
4. Restore the normal indication.
Press the MENU/EXIT button or
STOP
button.
PUSH TO ENTER
3. Set the date and time.
MULTI JOG
Rotate the MULTI JOG dial to select the year.
PUSH TO ENTER
MULTI JOG
Press the MULTI JOG dial to enter the year.
PUSH TO ENTER
The highlight moves to the month.
18
Displaying the date and time (Remote controller only).
Press the CLOCK button on the remote controller. With each press
of the CLOCK button, the displayed information changes as
follows.
Remote
controller
Press the
STOP
button to restore the normal indication.
Loading...