Quick Start Guide - Heated Throw
This is a Quick Start Guide Only. It is Important that you read the
do so may result in Damage or Personal Injury.
2
Ensuring there are no creases or folds, wrap
Ensure the detachable plug on the Throw is
DO NOT use in bed.
4
Heat Settings
Do not leave unattended when switched on.
DO NOT COVER CONTROLLER
When using the Throw, some people may be susceptible to a tingling sensation when alone or
0
0
Instructions fully for Safety and Correct operation of your product. Failure to
1
the Heated Throw around your body or drape
over your legs.
Ensure the Controller is on the outside of the
Throw. DO NOT COVER the controller
fully inserted and locked.
Allow cables to hand freely. DO NOT BEND,
KINK, TRAP or PINCH the cables.
DO NOT Sleep while using this product.
DO NOT use this product as an electric under
or over blanket.
3
0 = Off
1 = Low Heat
2 = Medium Heat
3 = High Heat
0 = Off
DO NOT Sleep while
using this product.
3
2
1
DO NOT use on heat
setting 3 continuously.
Turn down to setting 2
or 1 when warm enough
Controller will turn of
automatically after
approx. 3 hours.
Fully unravel the cables and Insert Plug into
Power Point and switch on.
Turn the heat setting to position “O” (off) then
Turn power off and Unplug at the wall.
Always Unplug when not in use
Store in dry place when finished.
Refer to “Recommended Cleaning
Instructions” section for directions on
cleaning the product.
when touching someone else using the Throw.
This “Tingling” feeling is known as an “electric field effect” and is occasionally known to happen
across all makes and brands of Throws. It is caused by the current flowing through the element
creating an Electromagnetic Field (EMF). Some people are more susceptible to feeling this EMF
tingling sensation than others. This is no cause for concern and is in no way an electric shock.
Page 2 of 16
Rev 1
T624W100DA2b
Heated Throw
INSTRUCTIONS
3 Hour Auto Off
Note: The specifications and/or components of this product are subject to change without prior notice
Model Number
Page 3 of 16
Rev 1
Page 4 of 16
Rev 1
1 IMPORTANT SAFEGUARDS ............................................................... 6
3 Connecting the Controller .................................................................. 8
4 Overheat Protection ........................................................................... 8
5 Using The Controller .......................................................................... 9
5.1 Auto Off........................................................................................................ 10
5.2 Pre Heat ....................................................................................................... 10
6 Using Your Heated Throw ................................................................ 10
7 Recommended Cleaning Instructions ............................................. 11
7.1 Treatment For Localised Soiling ............................................................... 11
7.2 Hand Washing (Recommended) ................................................................ 12
7.3 Drying .......................................................................................................... 12
8 Servicing Your Heated Throw and Controller ................................. 13
9 Electrical Schematic Diagram .......................................................... 13
10 Troubleshooting ............................................................................... 13
10.1 Troubleshooting Table ............................................................................... 14
11 Warranty ............................................................................................ 15
Page 5 of 16
Rev 1
Thank you for purchasing our Heated Throw. Each unit is manufactured to ensure
safety and reliability. Before using for the first time, please read the instruction
manual carefully and keep it for future reference.
1 IMPORTANT SAFEGUARDS
• Before connecting and switching on the Heated Throw, ensure that the voltage indicated on the
rating label corresponds to the mains voltage in your home.
• Read the instructions carefully, in conjunction with the illustrations, before using for the first time.
• If the cord of this Heated Throw is damaged, unplug and discontinue use of the product
immediately then contact the manufacturer.
• Check that your Heated Throw is not damaged before switching it on.
• Always unfold or unroll before switching on.
Failure to observe these instructions may result in overheating. This may activate the
overheat safeguard system, thus leaving the Heated Throw permanently inoperative.
Misuse of this Heated Throw will invalidate your warranty.
• When storing the Heated Throw, allow it to cool down before folding. Fold or roll neatly but not
tightly and without sharp bends in the heating elements. Store where no other heavy objects will
be placed upon it.
• The Heated Throw should not be used on an adjustable bed or chair. However, if the Heated
Throw is used on an adjustable bed or chair, check that the Heated Throw and cord do not
become trapped or rucked (creased or Bunched up), for example, in hinges.
• The Heated Throw is not to be used by young children unless the controls have been pre-set by a
parent or guardian, or unless the child has been adequately instructed on how to operate the
controls safely.
• This Heated Throw is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a person responsible for their
safety.
• This Heated Throw is not intended for use by young children or infirm persons without adequate
supervision.
• Heated Throws are intended for human use only. Not for animals and pets.
• Do Not Allow Pets or Animals To Lie or Chew On This Product or On The Electrical Cords Etc.
• Prolonged application at the highest heat setting can result in skin burns.
• Do not use the Heated Throw rucked (creased or Bunched up) or folded.
• Keep the controller away from an open window.
• Do not use pins in the Heated Throw as these may damage the electric wiring.
Page 6 of 16
Rev 1
• The flexible supply cord and controller must, as far as practicable, be kept outside of the Heated
Throw. Do Not Cover the Controller.
• Do not switch the power on if the Heated Throw is wet or in a folded state.
• Switch off at the power outlet and remove the plug from the mains when the Heated Throw is not
in use.
• Do not leave heavy objects on the Heated Throw, e.g. suitcases, books, etc. when the unit is
switched on as this will trigger the over temperature device and render the Heated Throw
PERMANENTLY inoperable. This may also invalidate the warranty.
• Do not dry-clean this Heated Throw. Cleaning liquid may have a damaging effect on the
insulation covering of the heating unit. Follow washing directions located on the Heated Throws
rating label and in this Instruction Manual.
• Do Not Use in Bed (note: the Throw is not to be used as an under blanket or Over blanket on the
bed.)
• This Heated Throw is not to be used continuously.
This Heated Throw is not to be used in Bed or while Asleep.
•
• If any abnormality or defect in operation is observed, discontinue its use immediately and consult
the distributor regarding its examination and/or repair.
• The Heated Throw should be examined frequently for signs of wear, either of the Heated Throw,
controller or flexible cord. If wear is visible or if any abnormality or defect in operation in the
Heated Throw is observed, discontinue use immediately and consult a qualified and registered
person for service. (i.e. such as an electrician)
• The Heated Throw must not be used on or near a water bed.
• Depending on the controller type, you may notice a blue flash in the controller when moving from
one setting to another. This is NOT dangerous. It is caused by the internal copper parts making
contact with the switching mechanism when moving.
• It is recommended that your Heated Throw is inspected by a qualified and registered person (i.e.
such as an electrician) after 3 years of use.
• This Heated Throw is intended for domestic use only. It is not intended for use in hospitals or the
like.
• Switch off from the power outlet and remove plug when the Heated Throw is not in use.
• Only use the controller supplied with this Heated Throw.
• For additional protection, it is strongly recommend that the use of a residual current device (RCD)
with a tripping current not exceeding 30mA be used on the circuit supplying this product. If you
are unsure if your home has this device, please contact your nearest Electrical Contractor.
• Always treat Electrical Appliances with the upmost care. Do not use this product in any other
fashion or for any other purpose other than stated in these instructions.
Page 7 of 16
Rev 1
3 Connecting the Controller
Ensure Power is Off and the Plug is Removed from the Wall Socket
• To fit the controller plug, simply hold the socket with one hand and push the
controller plug all the way until the locking tab locates over the lug on top of the
controller plug.
• To remove the controller, lift the locking tab up with your finger and pull the
controller plug directly out. Do Not Pull the controller cable and Do Not try and
pull the controller plug out without first lifting the locking tab as you will damage
the socket.
• Do Not fold, roll, kink or pinch the cables. Allow the cables to hang freely.
• Ensure the cables are not pulled so tight that they bend hard at the Heated
Throw connector end.
4 Overheat Protection
• The Heated Throw is fitted with numerous overheat safeguard systems. This offers
protection against overheating or damage to the elements by disengaging the
power to the elements before overheating hazards occur.
• Should there ever be a problem with the heating element in the Heated Throw, it will
automatically close down the operation and the Heated Throw will turn off.
• The controller must not be covered. The controller has built in protection, so that
if the controller overheats, or the heating element is damaged, it will automatically
close down the operation Permanently.
• Should this occur, the Heated Throw and Front Heat Level display lights
will turn off and a RED indicator light will illuminate through the back of
the controller. This indicates that the Throw and controller needs to be
replaced and cannot be repaired.
If in a bright room, you may need to cup your hands around the back of
the controller to make it darker so that the RED indicator light can be
seen.
Please refer to the Troubleshooting Guide in the back of this manual
before calling the service department or before returning the Heated
Throw.
Page 8 of 16
Rev 1
5 Using The Controller
Heat Level
Temperature
0
0
• Use your Heated Throw with Detachable Controller Model MC-111A3 Only.
• Do not use any other controller.
0 = Off
1 = Low Heat
2 = Medium Heat
3 = High Heat (For preheating only)
0 = Off
DO NOT Sleep while using this product.
DO NOT use this product as an electric under or over blanket.
DO NOT use in bed.
• To select the required heat setting, slide the “Temperature Select Slide Knob” up or
down to your desired setting.
• The selected position will be indicated by lighting up the corresponding Red light.
i.e. If Heat setting “1” is selected, 1 LED will illuminate.
If Heat setting “2” is selected, 2 LED’s will illuminate.
If Heat setting “3” is selected, 3 LED’s will illuminate.
If Heat setting “O” (Off) is selected (at either end of the slide) no LED’s will
illuminate.
TURN OFF AND UNPLUG WHEN NOT IN USE
When using the Throw, some people may be susceptible to a tingling sensation when
alone or when touching someone else using the Throw.
This “Tingling” feeling is known as an “electric field effect” and is occasionally known to
happen across all makes and brands of Throws. It is caused by the current flowing
through the element creating an Electromagnetic Field (EMF). Some people are more
susceptible to feeling this EMF tingling sensation than others. This is no cause for
concern and is in no way an electric shock.
LED Indicators
3
2
1
Select Slide
Knob
Page 9 of 16
Rev 1
5.1 Auto Off
This controller is fitted with a 3 hour Count Down Auto Off Timer which starts to
countdown from when your heat setting has been selected, and will switch power
off to the elements after approximately 3 hours. (+/- 15 Minutes)
Note: Once a heat setting has been selected and the controller is powered ON, the
countdown timer will not be affected by adjusting heat level.
The timer will only be reset to 3 hours by sliding the control knob to heat level
“O” or after being powered OFF and then back On.
When the controller has timed out, the element will turn off and the Red LED’s
will flash.
Slide the control knob to the “O” position to reset.
TURN OFF AND UNPLUG THE HEATED THROW WHEN NOT IN USE.
5.2 Pre Heat
The controller has a pre-heat facility in order to warm the Heated Throw Quickly.
Once you are warm enough, please turn the controller down to setting 2 or 3.
Please DO NOT leave the Heated Throw set on the Preheat setting (No. 3) once
you are warm enough as you may get too hot.
NOTE: The Heated Throw may not feel warm to touch unless it is wrapped
around your body. Areas of the Throw not in contact will stay cool.
6 Using Your Heated Throw
• Read the Important Safeguards section first, then ensuring the Heated Throw is
fully unfolded, not creased and the controller plug is fitted securely, you can then
plug in and switch on.
• Wrap the Heated Throw around your body or drape over your legs.
The Heated Throw MUST NOT be used as an Under Blanket (as per with an
ordinary Electric Blanket) instead the Heated Throw must only be used by
Wrapping around your body and shoulders or draping over your legs etc.
When Wrapping the Throw around your body and shoulders, ensure the
controller connection is at the bottom and facing on the outside for comfort.
If using in conjunction with another normal blanket, place the Heated Throw on
top of the other blanket. The Heated Throw must always be positioned on the
outside to prevent overheating.
• Do Not fold, roll, kink or trap the cables. Allow the cables to hang freely. Ensure
the cables are not pulled so tight that it bends hard at the Heated Throw
connector end.
Page 10 of 16
Rev 1
MISUSE AND FAILURE TO FOLLOW THESE INSTRUCTIONS MAY TRIGGER THE
PERMANENTLY INOPERATIVE. THIS MAY INVALIDATE THE WARRANTY.
IMPORTANT:
DO NOT Cover The Controller At Any Time.
The Heated Throw must not be used in Bed or while sleeping.
TURN OFF AND UNPLUG WHEN NOT IN USE
Store in dry place when finished.
OVERHEAT PROTECTION SYSTEM AND RENDER THE HEATED THROW
7 Recommended Cleaning Instructions
Ensure the Controller is Unplugged from the Power Point and
Disconnected from the Heated Throw Before Cleaning
Do Not Wring, Do Not Spin Dry, Drip Dry Only
7.1 Treatment For Localised Soiling
Never Use Hot Water as the Heated Throw may shrink and will void your
warranty.
NOTE: DO NOT Pre-Soak or use stain removers of any kind which contain
Bleach. This includes any of the Oxy pre-soakers or Stain Removers
Detach and Remove the Controller before cleaning the Throw.
• The area affected should be sponged gently using a natural wool detergent or
mild soap flakes dissolved in cold water, followed by two consecutive spongings
using clean, soap-free cold water.
Page 11 of 16
Rev 1
• Lightly compress the treated area between two towels to absorb excess water.
• Refer to the section “Drying” for drying instructions
DO NOT WRING OR SPIN DRY THE HEATED THROW. DRIP DRY ONLY.
• The connections to the Heated Throw must be kept free of moisture.
7.2 Hand Washing (Recommended)
Detach and Remove the Controller before Cleaning the Throw.
Never Use Hot Water as the Heated Throw may shrink and will void your
warranty.
DO NOT Pre-Soak or use stain removers of any kind which contain Bleach. This
includes any of the Oxy pre-soakers or Stain Removers
• After removing the controller, place the Heated Throw in cold water (bathtub or
large laundry tub is ideal) mixed with either a natural wool detergent or with mild
soap flakes.
• Soak your Heated Throw for approximately five minutes, and then gently
squeeze the soapy water through the Heated Throw.
• Rinse your Heated Throw thoroughly with clean cold water until no more suds are
visible, and allow water to drain off the Heated Throw.
Do Not Wring or Spin Dry the Heated Throw. Drip Dry Only
• Refer to the section “Drying” for drying instructions.
With normal use it is recommended that you hand wash your Throw once a year.
7.3 Drying
• Spread the Heated Throw out on a clean surface (e.g. a large table) to dry in a
shady area.
• Your Heated Throw can also be dried on a clothes line provided the majority of
water has been drained off, providing the Heated Throw is not creased or folded
and as long as pegs are not used on the element areas of the Heated Throw. i.e.
Hang from the edge of the Throw only.
Note: The Heated Throw must be thoroughly dried (including controller socket)
before using.
DO NOT WRING OR SPIN DRY THE HEATED THROW. DRIP DRY ONLY.
Page 12 of 16
Rev 1
8 Servicing Your Heated Throw and Controller
MC-111A3
NOTE: There are no user serviceable parts in this Heated Throw or controller.
• The Heated Throw should be examined frequently for signs of wear, either of the
Heated Throw Fabric, controller or flexible cord. If wear is visible or if any
abnormality or defect in operation in the Heated Throw is observed, discontinue
use immediately and consult a qualified and registered person for service. (i.e.
such as an electrician)
• It is recommended that your Heated Throw is inspected by a qualified and
registered person (i.e. such as an electrician) after 3 years of use.
• If the Heated Throw is not operating correctly, please check the Troubleshooting
Guide in the back of this manual before contacting our service department.
9 Electrical Schematic Diagram
10 Troubleshooting
If you have a problem with your Throw and/or controller, please check the
Troubleshooting table below to see if the problem can be resolved.
If the troubleshooting table is not able to help solve your problem, please call our service
department before returning the product for replacement as they may be able to help.
(Refer Warranty Page for Contact Number)
• If the problem cannot be resolved and you need to return the Heated Throw to the
retailer, we please ask that:
o The unit is packed carefully back into its original packaging.
o Original proof of purchase is attached.
o A brief note attached to the Heated Throw explaining the reason why it is being
returned.
Page 13 of 16
Rev 1
10.1 Troubleshooting Table
Problem Cause Remedy
No Power to
Controller / No
Heat Level
Indicator Lights
showing on Front
Display
No Heat Level
Indicator Lights
showing on Front
Display however
RED indicator light
is showing
through the back
of the controller.
Heat Level
Indicator Lights
showing on Front
Display but Throw
is not heating
The Temperature Slide Knob is in the “O” position
The Power Plug may not be plugged in to the power
point and switched on.
There may be no power to the power point
The controller has overheated and blown the OverTemp thermal fuse
The Heated Throw Elements have been damaged.
Detachable Plug from Controller to Heated Throw is
not fitted correctly or has come loose.
The selected heat setting is too low. Increase the Heat setting
Pre-heat time is too short.
Throw not in contact with Body
Slide the knob to setting 1, 2 or 3. The corresponding
front display Lights should illuminate.
Ensure the power plug is inserted into the power
point correctly and switch on.
Ensure there is power to the power point. Test with
another appliance such as a table lamp.
The Heated Throw elements have been damaged
and a new Heated Throw must be purchased.
Ensure the detachable plug is fitted correctly into the
socket on the Heated Throw and the locking tab has
clipped over the lug on the plug.
Allow the Heated Throw more time to heat up.
More time is required depending on the ambient
temperature.
The Throw may not feel warm to touch unless it is
wrapped around your body. Areas of the Throw not in
contact will stay cool
Heat Level
Indicator Lights
showing on Front
Display but cannot
change any of the
settings
Controller Slide
Knob is in the 1, 2
or 3 heat setting
position but no
Heat Level
Indicator Lights
showing on Front
Display.
Heat Level
Indicator Lights
Flashing on Front
Display
Controller is Warm
to Touch
Program may have locked up to protect itself due to a
power surge.
The Power Plug may not be plugged in to the power
point and switched on.
The controller has overheated
The Auto Off timer has activated and turned off the
Heated Throw.
Controller has Timed Out
This is normal Nothing to do. Is no cause for alarm.
Unplug the controller from the power point, wait 2
minutes and then plug in and switch on again.
Please follow the same steps as under “ No Power to
Controller / No Heat Level Indicator Lights ”
Please follow the same steps as under “ No Power
to Controller / No Heat Level Indicator Lights ”
Heated Throw will automatically turn off after
approximately 3 hours. Slide the Knob to the “O”
position, wait 5 seconds, then select heat setting 1, 2
or 3.
Slide the knob to the “O” position to reset then select
the desired heat setting.
Page 14 of 16
Rev 1
11 Warranty
WHAT’S COVERED?
5.2 Our goods come with guarantees that cannot be
fitness of the goods for any purpose, or as to
design, assembly, installation, materials or
good in any way whatsoever is limited to the
WHAT IS NOT COVERED?
WHAT WE WILL DO
5.5 These terms and conditions supersede and
exclude all prior and other discussions,
representations (contractual or otherwise) and
or any part of the goods. This includes
or the results that ought to be expected from
6.1 To claim under this warranty, you must first
via email
info@hegroup.com.au and explain the basis of
WARRANTY COSTS
GENERAL
originating from the store of purchase for the
product showing the retailer’s name, date of
1.1 H.E. Group Pty Ltd (“us” “we” or “our”)
warrants this good for a full replacement or
refund for a period of twelve months from the
date of purchase.
1.2 This warranty covers materials and
workmanship defects only.
2.1 This good is for household use only and if
used in any way other than as detailed in the
instruction manual will void this warranty.
2.2 This warranty does not apply to defects arising
from abuse, alteration, unauthorised or
unreasonable use of the good, nor does it
cover general deterioration due to usage.
2.3 This warranty does not apply to accessories
due to general deterioration or acts beyond
human control.
3.1 We will replace the good or provide a refund to
the value of the purchase price, if a defect is
discovered in the good during the warranty
period of twelve months subject to verification
of defect or malfunction and the date and proof
of purchase and purchase price.
4.1 Once we have received the goods and you
have complied with the warranty, our costs
associated with the warranty claim will be
borne by us.
4.2 No responsibility will be taken for goods lost,
mislaid or damaged whilst in transit.
5.1 The benefits of this warranty are additional to
any other rights and remedies you may have
under law.
excluded under Australian Consumer Law. You
are entitled to a replacement or refund for a major
failure and compensation for any other reasonably
foreseeable loss or damage.
You are also entitled to have the goods repaired
or replaced if the goods fail to be of acceptable
quality and the failure does not amount to a major
failure.
5.3 Notwithstanding 5.1, except as provided for in this
warranty, all express and implied warranties and
conditions under statute or general law as to the
merchantability, description, quality, suitability or
workmanship or otherwise are (where permitted
under law) expressly excluded.
5.4 To the extent permitted by law, our total liability
for loss or damage of every kind related to the
amount paid to the retailer by you for the good or
the value of the good.
arrangements relating to the supply of the goods
representations not made by us relating to the
performance of the goods or any part of the goods
using the good.
CUSTOMER CARE
contact our friendly customer service team on free
call 1800 079 124 or
your claim. Our customer service team will then
provide you with directions on how to make your
claim under this warranty.
6.2 This warranty is valid with the presentation of the
original proof of purchase receipt or tax invoice
purchase and amount paid, by you, for the good.
Address:
Phone No:
Email:
HE Group Pty Ltd, 47 Stephenson Street, Cremorne, Victoria 3121
1800 079 124 (free call)
info@hegroup.com.au
Page 15 of 16
Rev 1
April 2011
Edition
Page 16 of 16
Rev 1
Loading...