One Systems Array – 2 User Manual

CROSS FIELD ARRAY-2 (CFA-2)
Long Throw/High Intelligibility
All-Weather Loudspeaker System
V100/2015
The One Systems Cross Field Array-2™ (CFA-2) was designed to provi de v ery high intelligibility and acoustic output where long throw requirements are
specified. The CFA-2 is a nominal 55 degree horizontal by 30 degree array that
features a fully rotatable high frequency horn/waveguide. This allows the CFA-2
to be used in either a vertical or horizontal orientation and still allows the desired coverage patterns. The high frequency configuration consists of two large format close-spaced compression drivers coupled to a 2” (50.8mm) constant directivity horn. The low frequency configuration consists of 4 bandwidth optimized 10” (254mm) diameter woofers in a 2 x 2 array. The CFA-2 is ideal for both outdoor/direct weather long throw applications and indoor applications in high ambient noise environ men ts . Ty pi c al ap pl i cations are football and soc cer fiel ds, baseball fields and larg e theme park environm ents . Indoor environments such as basketball arenas and natatorium installations ar e w ell suited due to the ultra-
high system inte lligib ility.
In order to achieve maxi mum sys tem performance the CFA-2 should be high pass filtered using a 4 filter frequency can be set using the O ne Sy s tems SF -4 High Pass Filter system or by using any high quality DSP based loudspeaker processor. High pass filter frequencies as low as 60Hz may be used but maximum system dynamics and headroom are achieved by using the recommended 80Hz filter corner frequency.
The CFA-2 is a direct weather design that features a three layer stainless steel grill assembly. The enclosure design is a laminated fiberglass construction with high safety factory structural rigging points molded in the enclosure s hell . Ther e are 9 M10 rigging points and the system is supplied with a stainless steel “U” bracket for simple suspension. The “U” bracket also includes a stainless steel strap kit that allows the desired tilt angle to be set and maintained regardless of wind loading.
th
order (24dB/octave) high pass filter set to 80Hz. This
The system is also compatible with the One Systems Pole Mount System EX-3 if vertical tilt requirements are specified in a pole mount application. The One Systems PT-76 is also compatible with the CFA-2 when pan and tilt are required.
The CFA-2 has an internal 600 watt autoformer and an internal jumper system that allows the enclosure to be used in either a “Lo Z” (4 ohm) or “Hi Z” configuration. The aut o for mer t aps ar e 600 w atts , 300 watts, and 150 watts. The input will allow for either 70.7Vrms operation or 100Vrms operation. The autoformer is a very low insertion loss (<0.4dB) impedance converter that exhibits very wide bandwidth.
NOTE: The CFA-2 is factory configured f or 4 ohm operation. Internal jumpers are supplied and must be re-configured for “Hi Z” operation.
System input is a five position barrier strip. The input section features an aluminum weather cover with an integral IP68 rated glad nut. The gland nut will accommodate cable outside diameters of 7mm to 12mm (0.236” to 0.472”). The maximum diameter will accept most 2 conductor AWG12 cable assemblies.
FEATURES AND BENEFITS:
Very High Intelligibility Long Throw/High Acoustic Output Fully Rotatable High Frequency Waveguide IP 56 Direct Weather Rated Double Large Format High Frequency Drivers Lo Z and Hi Z User Switchable Operation 2 X 2 10” (254mm) Low Frequency Long Throw Array Multiple Fly Points and Rigging Accessories
SPECIFICATIONS:
Frequency Response: 60Hz – 16kHz Coverage Pattern: 55 x 30 Fully Rotatable
Passive Crossover Frequency: 1500 Hz
Inputs: 5-position barrier strip System Sensitivity: 104dB
(1watt-1meter) Maximum Calculated Output (Continuous) 134.8dB@ 1 meter*
(Peak Po wer/Peak Pressure) 140.8dB@ 1 meter * *(Based on RMS sound pressure levels) 137.8dB@ 1 meter
+3dB may be added for peak sound pressure levels) 143.8dB@ 1 met er Power Handling: 1200 watts Continuous
2400 watts Program 4800 watts Peak* * NOTE: all system power handling rating are amplifier headroo m de pen dent
Nominal Impedance 4 ohms or Hi Z* (70.7Vrms or 100V rms )
* User Configured via internal jumpers System Components: Low Frequency: 4 each 10” (254mm)
High Frequency: 2 each Large Format Titanium Compression Drivers
EASE 4.0 data
www.ONESYSTEMS.com
Suspension/Mounting points: 9 each M10 Weather Performance: IEC 529 IP 56
Dimensions (H x W x D) mm: 876.5 x 572.6 x 446.3* Inches: 34.5 x 22.5 x 17.6 * Height is for enclosure only (Height does not include U bracket)
Net Weight: 60.6 kg (133.6 lbs)
63.6kg (140.2lbs) with External “U” bracket Included Accessories Stainless Steel “U” Bracket and strap kit
Optional Accessories/Products Pole Mount System EX-3 (new 2012) PT-76 (new 2012) M10 Forged Shoulder Eye Bolt Kit SF-4 High Pass Filter (new 2012)
CONFIGURING THE CFA-2
NOTE: The One Systems CFA-2 has a factory installed 600 watt autoformer.
The CFA-2 may be configured to present either a “Low Impedance” (4 ohm) or “High Impedance” load to the amplifier. The CFA-2 is wired at the factory for 4 ohm operation. If a “High Impedance” configuration is required, the crossover input cup must be removed and the configuration jumpers must be moved as shown below.
For Low Impedance (4 ohms) all jumpers must be in POSITION 2. For High Impedance (either 70.7Vrms or 100Vrms) all jumpers must be in
POSITION 1.
THE INPUT WEATHER COVER MUST BE USED FOR ALL CFA-2 INSTALLATIONS, REGARDLESS OF SYSTEM INPUT IMPEDANCE!
Jumpers shown in “Low Z (4 ohm)” position 2
The input routing jumpers are configured from the factory in the position shown above (Low Z). They must be moved by the user if “High Z” (70.7Vrms or 100Vrms) operation is required.
NOTE:
For high-impedance connections the internal jumpers must be moved from position 2 to position 1.
Jumpers shown in “High Z” position 1
CONNECTING THE CFA-2
The input barrier strip wiring is shown below. NOTE the “No Connection” (NC) positions for each wiring configuration. Please note that when wiring for 100Vrms or 70.7Vrms operation there are various connections that are not used (NC) based on whether the desired operating voltage is 70.7Vrms or 100Vrms.
SUSPENDING THE CFA-2
The CFA-2 may be suspended using either the stainless steel “U” bracket (supplied) or by using either the Pole Mount System EX-3 for pole applications or the PT-76 for either wall or pole mounting. The CFA-2 may be suspended horizontally using points 1 and 3 shown below via M10 eyebolts.
The CFA-2 rigging points (M10 - 9 points) and mounting point for the “U” bracket hardware kit (M8 - 1 point (NOT A SUSPENSION POINT) are shown below.
The points shown in red are all M10. The single blue colored point is M8. The points are numbered in this image to illustrate intended usage as follows:
Points 1 and 2……………..”U” Bracket mount (the blue point, M8, is also used for the “U” bracket strap kit. The blue M8 point is NOT a structural point and is used for the “U” bracket strap ONLY!)
Points 1 and 3, 4 and 5…….Horizontal enclosure mount. NOTE: All 4 points,
(Points 1, 3, 4, and 5) must be used for horizontal mount configurations. Point 4 and 5 are for pull up and safety!
Point 6………………………Four points used for either the PT-76 or the Pole Mount System EX-3 (NOTE: Point 4 is used for the “link” portion of the PT-76 or the Pole Mount System EX-3 mounts)
The supplied “U” bracket requires the enclosure be suspended “upside down” with the high frequency section positioned near the bottom of the front baffle. The “U” bracket will allow adjustment in the vertical axis (tilt) only. See the image below. NOTE: THE CENTER HOLE IN THE U BRACKET IS FOR THE PULL
BACK STRAP ONLY! THIS HOLE MUST NOT BE USED FOR MOUNTING OR SUSPENSION!
CFA-2 orientation for external “U” bracket (supplied)
The CFA-2 is supplied with the external “U” bracket and a hardware kit to allow the enclosure to be tilted back and locked into position. This kit prevents wind loading and “gravity sag” from altering the required down tilt angle of the enclosure
The kit consists of: 1ea. Band-it AE4779 All Purpose Band 316SS (Black Coated) 475mm long
2ea. M8 304 grade stainless steel bolts 1ea. M8 304 grade stainless steel nylon insert nut 3 ea. 304 flat washers 1 ea. Lock washer
The M8 fitting is located between the M10 points.
NOTE: The M8 point should NOT be used for rigging.
The M8 point is to be used to mount the hardware kit ONLY!
THE CENTER HOLE IN THE U BRACKET IS FOR CONNE CTING THE STRAP
ONLY! DO NOT USE THE CENTER M8 HOLE IN THE U BRACKET FOR
MOUNTING OR SUSPENDING THE ENCLOSURE !!!
The “U” bracket kit is shown installed above and a close up below.
The stainless steel band is connected to the “U” bracket by using one M8 bolt and flat washer on the top as shown in the close up below. A second flat washer and the nylon insert nut are used below the “U” bracket to secure the stainless steel band to the top of the “U” bracket.
“U” bracket M8 bolt Flat Washer Stainless Steel Band
“U” Bracket Flat Washer M8 Nylon Insert Nut
M10 rigging point M8 point M10 rigging M8 bolt M10 rigging point Flat Washer Lock Washer The band is secured on the back of the enclosure using the M8 point, a flat
washer, a lock washer and the second M8 bolt as shown above.
Flat Washer Lock Washer M8 Bolt The above image shows the back of the CFA-2 and the strap kit mounting.
The CFA-2 is shown below with both the PT-76 and the Pole Mount System EX-
3. When the CF A-2 is suspended using either the Pole Mount System EX-3 or the PT-76 the enclosure must be oriented with the woofers near the bottom of the mount.
CFA-2 with PT-76
CFA-2 with Pole Mount System EX-3
NOTE: When the CFA-2 is used with either the PT-7 6 or the Pol e M ount System EX-3 the enclosure is rotated 180 degrees as shown above and below. The high frequency horn is located near the top for use with the PT-76 or the Pole Mount System EX-3.
Enclosure orientation for PT-76 and Pole Mount System EX-3
Installation instructions for both the Pole Mount EX-3 and the PT-76 may be found in the “Documentation” section of the One Systems web site. (www.onesystems.com)
© 2014 One Systems, Inc. www.onesystems.com
Loading...