Page 1
ADIRONDACK
TÊTE-À-TÊTE CHAIR
92365
ASSEMBLY AND OPERATING INSTRUCTIONS
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
Copyright© 2004 by Harbor F reight Tools®. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or
form without the express written consent of Harbor Freight T ools.
For technical questions and replacement parts, please call 1-800-444-3353.
Page 2
Specifications
Maximum T able Load 40 Lbs.
Maximum Seat Weight Limit 250 Lbs. Each
Center T able Dimensions 12” (Front) x 26” W (Rear) x 29” L (11 Slats)
T able Height F rom Ground 22 ”
Angle of Seat ~25°
Back Rest Dimensions 31-1/2” H x 17” W (7 Slats)
Weight 43 Lbs.
Save This Manual
You will need the manual for the safety warnings and precautions, assembly instructions,
operating and maintenance procedures, parts list and diagram. Keep your invoice with this
manual. Write the invoice number on the inside of the front cover. Keep the manual and
invoice in a safe and dry place for future reference.
Safety Warnings and Precautions
WARNING: When using tool, basic safety precautions should always be followed to
reduce the risk of personal injury and damage to equipment.
Read all instructions before using this tool!
1. Keep work area clean. Cluttered areas invite injuries.
2. Observe work area conditions. Keep work area well lit.
3. Keep children away. Children must never be allowed in the work area. Do not allow
children to climb upon, play around or stand on this chair.
4. Do not exceed weight capacity of this chair. To do so may cause personal injury or
property damage.
5. Use the right chair for the job. Do not modify this chair and do not use this chair f or a
purpose for which it was not intended. Do not climb or stand on this product.
6. Use eye protection. Alwa ys wear ANSI approved impact safety goggles during assembly.
7. Do not overreach. Keep proper footing and balance during assembly.
8. Maintain products with care. Keep products clean for better and safer performance.
Periodically check hardware to make sure it is secure .
9. Check for damaged parts. Before using an y product, an y part that appears damaged
should be carefully checked to determine that it will operate properly and perform its
intended function. Check for any brok en parts, deteriorating wood, and any other condition
that may affect proper oper ation. An y part that is damaged should be properly repaired
or replaced by a qualified technician.
10. Replacement parts and accessories. When servicing, use only identical replacement
parts. Use of any other parts will void the warranty. Only use accessories intended for
use with this item. Approved accessories are av ailable from Harbor F reight Tools.
Page 2SKU 92365 For technical questions, please call 1-800-444-3353
Page 3
11. Stay alert. Watch what y ou are doing, use common sense. Do not assemble any product
when you are tired.
12. Do not assemble the Chair if under the influence of alcohol or drugs. Read warning
labels if taking prescription medicine to determine if your judgment or reflexes are impaired
while taking drugs. If there is any doubt, do not assemble the Chair.
13. Maintenance. F or your saf ety, service and maintenance should be performed regularly
by a qualified technician.
Warning: The warnings, cautions, and instructions discussed in this instruction manual
cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be
built into this product, but m ust be supplied by the operator.
Unpacking
When unpacking, check to make sure the parts listed on page 8 are included. If any
parts are missing or broken, please call Harbor Freight Tools at the number on the cover of
this manual as soon as possible.
Assembly
Refer to the Assembly “Step” diagrams, FIGURES 1 and 2 on pages 4 through
6, the Parts List Diagrams on page 8, and the cov er photo .
Step 1. Attach the Left Front Leg (H) and the Right Front Leg (C2) (oriented as shown) to the
Seat (B) using 3 Bolts (K) per side. Use the included washers and nuts to secure the
Bolts (K).
Step 2. Attach both Back Supports (D1 & D2) to the inner sides of the Seat (B), using 2 Bolts
(K) per side. Use the included washers and nuts to secure the Bolts (K).
STEP 1 STEP 2
REV 12/04
Page 3SKU 92365 For technical questions, please call 1-800-444-3353
Page 4
Assembly (continued)
Step 3. Attach the Left Arm (G2) to the Left
Front Leg (H) using 2 Bolts (K), and
then attach it to the Left Back Support (D2) using 1 Bolt (K). Use the
included washers and nuts to secure
the Bolts (K). Attach the Right Arm
(E2) to the Right Front Leg (C2), using 2 Wood Screws (M). Attach the
rear of the Right Arm (E2) to the
Right Back Support (D1) using 1
Long Bolt (L). Use the included
washer and nut to secure the Bolt (L).
STEP 3
Step 4. Attach the Back (A) to the Seat (B)
and Back Supports (D1 & D2), using 6 W ood Scre ws (M).
STEP 4
REV 12/04
Page 4SKU 92365 For technical questions, please call 1-800-444-3353
Page 5
Assembly (continued)
Step 5. Attach the Front Support (F) to the
Front Legs (H and C2) using 2 Wood
Screws (M) per side.
STEP 5
Step 6. Use Steps 1 through 5, above, to as-
semble the other chair . The arms will
mount on the opposite side on the
second chair.
STEP 6
REV 12/04
Page 5SKU 92365 For technical questions, please call 1-800-444-3353
Page 6
Assembly (continued)
Step 7. Position the Chairs as shown below. Attach the Front Desktop (I) to the Right Arm
(G1) and the Left Arm (G2). Attach the Rear Desktop (J) to the Right Arm (G1) and the
Left Arm (G2). Both hav e Do wels that are shown in the insert in Step 7 below.
STEP 7
BEFORE USE REMINDERS
a. Recheck the alignment of all
parts and the tightness of all
fasteners.
b. Set up the chair on a flat, level
location.
c. Do not exceed load capacity.
FIGURE 1
Side Vie w of Chair
REV 12/04
Page 6SKU 92365 For technical questions, please call 1-800-444-3353
Page 7
Rear View of Chair
FIGURE 2
Maintenance
1. This chair is made of natural Fir wood. This beautiful material will naturally weather
over time, especially if used outdoors. You can manage the speed and extent of this
weathering by controlling the environment in which the chair is used and stored, as
well as any coatings you may apply.
2. Leaving the chair outside exposed to weather, especially direct sun, rain and salt air ,
will speed the weathering process. This can be slowed by removing the chair from
these conditions, or covering it with a suitable cover.
3. You may wish to stain, varnish or paint the chair. If so, follow the instructions supplied
with these coatings.
4. Occasionally wash the chair with a garden hose or pressure sprayer to remove
accumulated dust or dirt. Wipe down or blow off any remaining water left on the chair
after washing.
5. Periodically (perhaps once per year), recheck the tightness of all fasteners. Normal
usage of the chair and weathering of the wood may cause fasteners to loosen.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUF ACTURER AND/OR DISTRIBUT OR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANU AL
AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY
REPRESENT ATION OR WARRANTY OF ANY KIND T O THE B UYER THAT HE OR SHE IS QUALIFIED TO
MAKE ANY REP AIRS TO THE PRODUCT OR THA T HE OR SHE IS QU ALIFIED TO REPLA CE ANY P AR TS
OF THE PR ODUCT . IN F ACT, THE MANUF ACTURER AND/OR DISTRIBUT OR EXPRESSL Y STA TES THAT
ALL REP AIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED
TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING
OUT OF HIS OR HER REP AIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERET O, OR
ARISING OUT OF HIS OR HER INST ALLATION OF REPLACEMENT P AR TS THERET O.
Page 7SKU 92365 For technical questions, please call 1-800-444-3353
Page 8
Parts List
NOTE: Some parts are listed and shown for illustr a-
tion purposes only and are not available individually
as replacement parts.
Page 8SKU 92365 For technical questions, please call 1-800-444-3353
Loading...