One Stop Gardens 68354 User Manual

Digital Weather Station

68354 Digital Weather Station

Read this material before using this product. Failure to do so can result in serious injury. SAVE THIS MANUAL.

When unpacking, make sure that the product is intact and undamaged. If any parts

are missing or broken, please call 1-800-444-3353 as soon as possible.

Visit our website at: http://www.harborfreight.com

or form without the express written consent of Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing

improvements, actual product may differ slightly from the product described herein. Tools required for assembly and service may not be included.

Specications

and caution are factors which cannot be built into this product, but must be supplied by the operator.

Batteries

Channels 3 Receiving Channels

Mounting Wall and Stand Mounting

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.

4 “AAA” (Not included) 2 for Station / 2 for Transmitter

Save This Manual

Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and the receipt in a safe and dry place for future reference.

Important Safety Information

In this manual, on the labeling, and all other information provided with this product:

This is the safety alert symbol. It is

used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.

General Safety Warnings

WARNING Read all safety warnings and

instructions. Failure to follow the warnings and

instructions may result in serious injury.

Save all warnings and instructions for future reference.

1. Position batteries in proper polarity and do not install batteries of different types or polarity.

2. Properly dispose of all used batteries.

3. This product is not a toy. Keep Weather Station and Transmitter out of reach of children.

4. Inspect before use; do not use if parts are damaged.

SAVE THESE

INSTRUCTIONS.

Display and Key Functions

Power

Indicator

Alarm

Time

Indoor

Temp Trend

Current

Weather

Indoor

Comfort

Indicator

Channel

Indicator

DOWN Adjust data in any set mode

MODE Press for 3 seconds to enter setting mode

MAX/MIN Switch between temp and humidity

Date

Outdoor

Temperature

Press for 3 seconds to change Year and Day of Week

Day

Outdoor

Reception

Icon

Moon

Phase

Outdoor

Humidity

Snooze

Indoor

Temp

Indoor

Humidity

Outdoor

Temp Trend

5. Use as intended only.

6. The warnings, precautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense

ALM Enter alarm setting / Turn on/off alarm

ALERT Set temp alert / Turn on/off temp alert

CH Switch between Transmitter channels

SNZ Activate snooze function on alarm

Page 2For technical questions, please call 1-800-444-3353.SKU 68354

Setup Instructions

Transmitter will have the temperature displayed with the number 1 against it and so on).

Read the ENTIRE IMPORTANT SAFETY

INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product.

Installing Batteries

1. NOTE: Install the Weather Station’s batteries rst.

2. Open the Weather station’s battery compartment cover.

3. Install two “AAA” batteries, making sure to follow polarity marked on the inside of the compartment.

4. Close battery compartment cover.

5. NOTE: Once batteries are in place, the LCD will

light up briey and a short beep will sound. Then the

indoor temperature and humidity will automatically display. If the indoor temperature is not displayed after a few seconds, remove the batteries and wait for at least 10 seconds before reinserting them.

6. Within three minutes of activating the Weather Station, insert the Transmitter’s batteries.

7. Open the Transmitter’s battery compartment cover.

8. Install two “AAA” batteries, making sure to follow polarity marked on the inside of the compartment.

9. Close battery compartment cover.

3. When all Transmitters are set up, a testing period will follow, during which the display switches between all received Transmitters at random. Press any key to stop this process.

4. The display will show the temperature for the rst Transmitter. The process also stops automatically if no keys are pressed for a few minutes.

5. Once the remote temperature has been received and displayed on the Weather Station, the time code reception is automatically started. This will take about 7 minutes in good weather conditions.

NOTE: This 7-minute time period is an excellent opportunity to install the Transmitter(s) in suitable location(s) outdoors. To ensure

sufcient 433 MHz transmission, do not install

Transmitter(s) more than 100 meters from where the Weather Station will be positioned.

6. If after 10 minutes the time code has not been received, use the MODE key to manually enter a time initially. The clock will automatically attempt each hour to receive the time. When this is successful, the received time will override the manually set time. The date is also updated with the received time.

7. If the Weather Station cannot receive the time code signal (perhaps because of weather disturbances or transmitting distance), the time can be manually set. The clock will then work as a normal clock.

10. NOTE: When battery power is low, the battery icon will appear on the Weather Station/Transmitter’s LCD display.

Testing Weather Station/ Transmitter Connection

1. After inserting batteries into Transmitter, the Weather Station will start receiving readings from the Transmitter. The outdoor temperature should be displayed. If this does not happen within 15 minutes, the batteries will need to be removed from both units and reset, following the above instructions.

2. NOTE: The Weather Station can take up to 3 remote transmitters. Follow the above steps for each extra Transmitter, making sure to leave 10 seconds in between the reception of the last Transmitter and the set-up of the next Transmitter.

The Weather Station will number the

Transmitters in the order of set-up (the rst

Channel Settings

1. Once the batteries are inserted (and BEFORE replacing Transmitter battery cover), use the Channel Key on the back of the Transmitter to select the channel. (If there is more than 1 Transmitter, please choose a different channel.

2. Once all settings have been made, close the Transmitter battery compartment cover and use the mounting hole to mount the Transmitter on an outdoor wall or window.

3. NOTE: The max. open distance between the Weather Station and the Transmitter is 328 ft. (100 meters). Do not install the Transmitter at a distance greater than 328 ft. Otherwise, the Weather Station will not a receive a proper transmitter signal.

4. Keep out of direct rain and direct sun to prevent inaccurate readings. Air conditioning or indoor heat can effect the signal, leading to incorrect readings.

Page 3For technical questions, please call 1-800-444-3353.SKU 68354

+ 4 hidden pages