Page 1
Thank you for selecting the APEX 4 Portable Printer. This guide provides an illustrative
reference of the initial steps to quickly get your Model APEX 4 up and running. To keep
your printer performing at its best, please replace the battery every 15 – 18 months and
perform routine maintenance as speci ed in the maintenance section of this guide. Refer
to the User’s Guide for more detailed information on the operation and use of the Model
APEX 4. A copy of the User’s Guide is available at www.datamax-oneil.com
APEX 4 Overview
MCR Slot
Print Head
Paper
Compartment
Status
Indicator LEDs
On/O
Button
Paper Feed
Button
AC Adaptor
Port
Serial or
USB Port
Platen
Roller
IrDA
Window
Belt Clip
Communication: All APEX 4 printers ship in USB and Bluetooth™ mode.
IrDA, 802.11g and MCR are optional features. Refer to the
User Guide for set-up instructions.
Copyright © 2010, Datamax-O’Neil. All rights reserved.
Performing Self Test
1. The printer must be OFF.
2. Press and hold the Paper Feed Button.
3. While holding the Paper Feed Button, press the ON/OFF Button and release.
4. A self-test will print. The self-test shows the printer rmware version, the current printer
settings and a list of any optional or special features installed.
LED Status Condition Function
LED #1
Green
Flashing
Power is ON and the printer is in
USB mode
Steady Communicating with host
Blue
Flashing
Power is ON and the printer is in
Bluetooth mode
Steady Transmitting/receiving
Amber
Flashing
Power is ON and the printer is in
802.11b/g mode
Steady Transmitting/Receiving
LED #2
Battery
Amber Steady
Battery is being charged. The LED will
turn o when the battery is fully charged
LED #3
Magnetic Card
Reader
&
Printer Error
Green
Steady
• Indicates that MCR or SCR is ready to
accept data
Flashing
• Indicated that printer is in USB Boot-
loader mode (USB cable is plugged in
and Dip Switches 5 and 7 are on)
Note: If USB is unplugged, LED will ash
Amber until printer is reset manually
LED#1
LED#2 LED#3
Status Indicator LEDs
Press the ON/OFF button to turn the printer on. Three LED indicators located on the
top of the printer indicate various printer functions.
The table below describes the normal function of each of the Printer’s Status LEDs
Please refer to User’s Guide for detail Error/Warning LED Panel. A copy of the User’s Guide is
available at www.datamax-oneil.com.
APEX 4
Quick Start Guide
7A300010 Rev A.
Page 2
Installing the Paper Roll
The APEX 4 has a “drop-in” paper load system. You can quickly and easily change the paper roll by
pressing the Paper Door Release Button.
1. Press the paper door release button. The door will open slightly.
Open the rest of the way as shown.
2. Install paper roll
3. While pressing Paper Door Release button, close paper door.
4. Press paper door down and let go of the Paper Door Release button.
5. Turn on the printer by pressing Power button and test the paper advance
function by pressing the Paper Feed button. Verify that paper advances correctly.
Installing the Battery
Your APEX 4 printer comes with a 7.4V, 2250mAh Lithium-Ion Battery. Batteries are shipped uncharged.
NOTE: In 15 – 18 months, please replace the battery. The date code on the battery will help determine
when you need to replace it. The rst two digits represent the year and the next two the week
of manufacture.
1. Unlock the battery door by sliding the battery door locking tab down.
2. Open the battery door to an angle of about 90 degrees. (Do not force open)
3. Insert battery as shown (non-contact end rst) allowing the contact end to drop
into place).
Charging the Battery
For optimal performance, we recommend charging the battery twice before initial use. Charge the
battery for 3 hours; disconnect power adaptor, reconnect and charge again. After this initial charge,
charge battery for 180 minutes whenever the low battery indicator comes on or as directed by your
IT team.
1. Plug battery charger adaptor output cable in the battery charger connector.
2. Plug battery charger adaptor into the appropriate AC line voltage socket.
3. LED will illuminate indicating that the battery is being charged.
4. The battery will be fast charged and after 180 minutes the LED will turn o.
Note: Pull Paper roll leader out of
printer. Note direction of
paper travel
Tearing Paper
To tear paper: The printer’s
paper door acts as a tear
bar. Pull one edge of the
paper against the tear bar as
indicated, then tear down and
across against the tear bar to
tear the paper.
Careful! The tear bar may have sharp edges.
Pulling up and/or sideways without using the
tear bar can cause a paper jam due to paper
misalignment in the print head mechanism.
Battery
Door Tab
Li-Ion
Battery
Please refer to the General Precautions and Safety Information listed in the User Guide.
A copy of the User’s Guide is available at www.datamax-oneil.com
4. Close and lock the battery door by sliding the battery door locking tab up.
Note: Ensure that the battery side that
has the two (2) contact terminals
faces down in order to make
contact with the spring probes
inside the battery compartment.
Paper Door
Release Button
The Paper Door Release button must be depressed when opening and closing the paper door.
Opening the paper door without pressing the Paper Release Button can cause damage to your printer.
Note: Paper Door Release button must
be depressed when opening and
closing paper door.
Loading...