One for All PVR 6, URC-6131, URC-6131nw User Manual
PVR 6 Owners Manual.fm Page 0 Monday, December 20, 2004 11:17 AM
6-Device PVR Universal Remote Control
Control Remoto Universal de 6
Dispositivos con functiones de PVR
User’s Guide
Guía del Usuario
PVR 6 Owners Manual.fm Page 1 Monday, December 20, 2004 11:17 AM
OWNER’S MANUAL
TABLE OF CONTENTS
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Features and Functions . . . . . . . . . . . . . . . . . . . . . . .2
Key Charts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Device Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Installing Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Programming Device Control . . . . . . . . . . . . . . . . . . .6
Programming DVD Player/ VCR Combo . . . . . . . . . . .8
Searching for Your Code. . . . . . . . . . . . . . . . . . . . . . .8
Checking the Codes . . . . . . . . . . . . . . . . . . . . . . . . . .9
Programming Master Power. . . . . . . . . . . . . . . . . . . .9
Programming the POWER Key for Master Power .9
Operating Master Power . . . . . . . . . . . . . . . . . . . .9
Clearing Master Power . . . . . . . . . . . . . . . . . . . .10
Using Keymover. . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Programming Keymover . . . . . . . . . . . . . . . . . . .10
Restoring Keymoved Keys to Default Settings. . .10
Restoring a Single Keymoved Key . . . . . . . . .10
Restoring All Keymoved Keys in a Single Mode .
11
Re-assigning Device Keys. . . . . . . . . . . . . . . . . . . . .11
Changing Volume Lock . . . . . . . . . . . . . . . . . . . . . . .11
Locking Volume Control to One Mode (Global
Volume Lock) . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Unlocking Volume Control for a Single Device
(Individual Volume Unlock) . . . . . . . . . . . . . . . . .12
Unlocking All Volume Control (Restoring Default
Setting). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
About Upgrading . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Upgrade Exclusions . . . . . . . . . . . . . . . . . . . . . . .14
Customer Support. . . . . . . . . . . . . . . . . . . . . . . . . . .14
Instructions to the User . . . . . . . . . . . . . . . . . . . . . .14
Limited Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Additional Information . . . . . . . . . . . . . . . . . . . . . . .15
Manufacturer’s Codes (Códigos del Fabricante) . . .34
Setup Codes for Audio Receivers (Códigos de
Configuración para Receptores de Audio) . . . . .34
Setup Codes for Cable Boxes (Códigos de
Configuración para Cajas/Convertidores de Cable)
34
Setup Codes for CD Players (Códigos de
Configuración para Reproductores de CDs) . . . .35
Setup Codes for DVD Players (Códigos de
Configuración para Reproductores DVD) . . . . . .36
Setup Codes for DVD/VCR Combos (Códigos de
Configuración para Aparatos Combinados DVD/
Videograbadora) . . . . . . . . . . . . . . . . . . . . . . . . .36
Setup Codes for PVR/DVRs (Códigos de
Configuración para PVR/DVRs, Grabadores
Personales en Disco Duro) . . . . . . . . . . . . . . . . .37
Setup Codes for PVR/DVR/Satellite Receivers
Combos (Códigos de Configuración para Aparatos
Combinados PVR/DVR/Receptores de Satélite) . 37
Setup Codes for Satellite Receivers (Códigos de
Configuración para Receptores de Satélite) . . . 37
Setup Codes for TVs (Códigos de Configuración
para Televisores) . . . . . . . . . . . . . . . . . . . . . . . . 38
Setup Codes for TV/DVD Player Combos (Códigos
de Configuración para Aparatos Combinados TV/
DVD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Setup Codes for TV/VCR Player Combos (Códigos
de Configuración para Aparatos Combinados TV/
VCR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Setup Codes for VCRs (Códigos de Configuración
para Videograbadoras). . . . . . . . . . . . . . . . . . . . 41
INTRODUCTION
The One For All 6-Device PVR Universal
Remote Control (URC-6131nw) is designed
to remotely operate up to six home
entertainment dev ices and features intuitive
and easy-to use buttons to operate PVR
(Personal Video Recorder)/DVR (Digital
Video Recorder) and DVD components. Its
sophisticated technology will allow you to
consolidate all of your original home
entertainment remote controls into one
easy-to-use product. Advanced features
include:
• Intuitive buttons to allow easy access
to your PVR/DVR functions and
menus
• Direct code setup for easy device
programming
• Step and Set code setup and Code
Verification for an alternate way to
program devices
• Master Power function for master on/
off control of all of your equipment
with a single keystroke
• Volume Lock to lock volume controls
to one mode or individual modes
Table of Contents 1
PVR 6 Owners Manual.fm Page 2 Monday, December 20, 2004 11:17 AM
ONE FOR ALL 6-DEVICE PVR UNIVERSAL REMOTE CONTROL
• Device Key Re-Assignment to remotely
control a second (duplicate) device
• Color-coded keys to quickly locate
popular functions
• Code library for popular video and
audio devices
The URC-6131 remote control requires two
(2) new AAA alkaline batteries (not
included) and some easy programming to
control your devices. For best results, please
read and perform all instructions listed
here. Also, keep these instructions for future
reference.
FEATURES AND FUNCTIONS
Use the illustration below to locate features
on the One For All 6-Device PVR Universal
Remote Control (URC-6131nw) and then
study the “Key Charts” to learn how they
function.
To find out what type of devices can be
controlled by each device key after
programming, see the “Device Table” on
page 5.
2 Features and Functions
PVR 6 Owners Manual.fm Page 3 Monday, December 20, 2004 11:17 AM
OWNER’S MANUAL
KEY CHARTS
When the LED (red
light) blinks, the
remote control is
working and (after
programming) is
sending signals.
Press TV, PVR, DVD,
CBL/SAT, AUD, or VCR
once to select a
desired home
entertainment device
to control. Also see
the “Device Table” on
page 5.
Press POWER once to
turn on or off the
selected device. For
master power control,
see “Programming
Master Power” on
page 9.
Press MENU once to
display your selected
device’s main menu.
For PVR/DVRs, use
PVR Menu.
Use INFO to display
the current channel
and program
information.
Use GUIDE to display
your selected device’s
program guide or
setup menu.
Use EXIT to exit from
your selected device’s
guide or menu.
Use the Cursor Keys
to move the cursor in
the program guide
and menu screens.
Use OK to choose
options from your
selected device’s
menu or guide.
In the AUD mode, use
SELECT to set the
surround
sound.Use
(or ) to adjust
the volume higher (or
lower).Use
(or ) to adjust the
balance left (or right).
Use VOL + (or VOL -)
to raise (or lower) the
sound volume.
Use CH + (or CH -) to
select the next higher
(or lower) channel.
Press MUTE once to
turn the sound off or
on.
Use to command
your PVR/DVR to
instantly replay the
last 7 seconds of a
program you are
viewing.
Features and Functions 3
PVR 6 Owners Manual.fm Page 4 Monday, December 20, 2004 11:17 AM
ONE FOR ALL 6-DEVICE PVR UNIVERSAL REMOTE CONTROL
Press PREV once to
recall the last viewed
channel and to page
back one screen on
the main menu.
In the AUD mode, use
PREV to select the
receiver band.
Use or to
perform the Thumbs
Down or Thumbs Up
feature on your Tivo/
PVR/DVR device.
Press PVR MENU once
to turn the PVR/
DVR’s main menu on
or off.
Use to command
your PVR/DVR to
skip or advance
through a recorded
program scene or
commercial.
Use the Transport
Keys to control your
VCR, PVR/DVR, DVD
player, or VOD (Video
On Demand) if
available on your
cable or satellite
service.
Use CC to select
closed captions, if
available on your
cable/satellite service
or DVD.
Press SUBT. once to
turn subtitles on or
off, if available.
Use ANGLE/SLEEP to
perform the angle
function on your
DVD player or to set
the sleep timer on a
selected device if
equipped with this
feature.
Use for slow
motion playback on a
VCR, PVR/DVR, or
DVD player equipped
with this feature.
Press PLAY to cancel
slow motion.
Use the keypad (1 ~ 9
and 0) to directly
select channels (e.g.,
009 or 031).
In the AUD mode, use
the keypad (1 ~ 9
and 0) to select audio
sources 1 through 10.
4 Features and Functions
Press REC twice to
record a PVR/DVR or
VCR program.
Use AUDIO to select
an alternate audio
channel (e.g.,
Spanish).
Press ENTER once
after entering the
channel numbers on
some TVs.
PVR 6 Owners Manual.fm Page 5 Monday, December 20, 2004 11:17 AM
OWNER’S MANUAL
DEVICE TABLE
Use TV/VID to switch
the TV’s input to view
TV or video
programs.
Use PIP to switch the
Picture-In-Picture
feature on or off (if
available on your
TV).
Use SWAP to switch
images and sound
between the main
and window pictures.
Use MOVE to move the
window picture to
different positions in
the main picture.
Use SET for all
programming
sequences.
DEVICE KEY CONTROLS THESE
DEVICES
Cable Boxes (Converters),
Satellite Receivers, or
Satellite/PVR/DVR
Combos
VCR s or TV/ VCR
Combos
DVD Player, DVD Player/
VCR Combos, or TV/
DVD Player Combos
Audio Receivers or CD
Players
NOTE: Audio Receiver/DVD Player Combos
(i.e.,Home Theater In A Box) are listed in
“Setup Codes for Audio Receivers (Códigos de
Configuración para Receptores de Audio)” on
page 34.
NOTE: Please refer to the table below when
performing the instructions in
“Programming Device Control” on page 6 or
“Programming DVD Player/ VCR Combo” on
page 8.
After programming, the One For All 6Device PVR Universal Remote Control
(URC-6131nw) will be able to control the
following types of devices:
DEVICE KEY CONTROLS THESE
DEVICES
Te l e v i s i o n s
PVR/DVRs (Personal
Video Recorders/Digital
Video Recorders)
Features and Functions 5
PVR 6 Owners Manual.fm Page 6 Monday, December 20, 2004 11:17 AM
ONE FOR ALL 6-DEVICE PVR UNIVERSAL REMOTE CONTROL
INSTALLING BATTERIES
1. On the remote control back, press on
the battery door to release it, then lift
off the battery door.
❶
2. Obtain two (2) new AAA alkaline
batteries. Match the + and – marks on
the batteries to the + and – marks in
the battery case, then insert the new
batteries.
3. Press the battery cover back into place.
❸
4. Test the remote control by pressing any
mode key (e.g., TV). If the batteries are
inserted correctly, the LED (red light
located under the POWER key) will
blink once.
NOTE: When batteries need replacement, the
remote control will stop operating. Remove
the old batteries and insert new ones within
10 minutes to ensure all of your programming
information is restored.
6 Installing Batteries
PROGRAMMING DEVICE
CONTROL
The One For All 6-Device PVR Universal
Remote Control (URC-6131nw) is
preprogrammed at the factory to operate an
RCA TV, VCR, and satellite receiver, a Philips
Tivo PVR/DVR, a Toshiba DVD player, and a
Pioneer audio receiver/amplifier. To control
❷❷
devices other than the default brands,
perform the following steps; otherwise skip
this section.
PVR 6 Owners Manual.fm Page 7 Monday, December 20, 2004 11:17 AM
OWNER’S MANUAL
NOTE: For DVD Player/VCR Combo control,
see the next page.
1. Turn on a desired device (e.g., VCR or
DVD player) and, if applicable, insert
media (e.g., cassette or disc).
NOTE: Please read steps 2 through 4
completely before proceeding. Highlight or
write down the codes and device you wish to
program before starting step 2.
2. On the remote control, press a device
key once (i.e., TV, PVR, DVD, CBL/SAT,
AUD, or VCR).
NOTE: To program control of a cable box or
satellite receiver, press CBL/SAT once.
NOTE: To program control of a CD player or
audio receiver, press AUD once.
NOTE: To pr og ram co nt rol of a T V/ VC R
Combo, press VCR once. After programming,
you will be able to control channel selection,
volume, and VCR functions.
NOTE: To pr og ram co nt rol of a T V/ DV D
Player Combo, press DVD once. After
programming, you will be able to control
channel selection, volume, and DVD
functions.
3. Press and hold SET until the LED (red
light) blinks twice, then release SET.
4. Use the “Manufacturer’s Codes
(Códigos del Fabricante)” (starting on
page 34) to locate the type of device
and brand name and then enter the
first four-digit code for your device. If
performed correctly, the LED will
blink twice.
NOTE: If the LED did not blink twice, repeat
steps 2 through 4 and enter the same code
again.
steps 2 through 5, trying each code for
your brand until you find one that
works. If it still doesn’t work, try
“Searching for Your Code” on page 8.
NOTE: If the device does not have a POWER
key, press the (PLAY) key.
6. Repeat steps 1 through 5 for each
device you want to control. For future
reference, write down each working
device code in the following boxes:
TV Code:
Brand Name:_____________________
PVR Code:
Brand Name:_____________________
DVD Code:
Brand Name:_____________________
CBL/SAT Code:
Brand Name:_____________________
AUD Code:
Brand Name:_____________________
VCR Code:
Brand Name:_____________________
5. Aim the remote control at the device
and press POWER once. The device
should turn off. If it does not, repeat
Programming Device Control 7
PVR 6 Owners Manual.fm Page 8 Monday, December 20, 2004 11:17 AM
ONE FOR ALL 6-DEVICE PVR UNIVERSAL REMOTE CONTROL
PROGRAMMING DVD
PLAYER/ VCR COMBO
1. Turn on the DVD Player/VCR Combo
and insert a DVD.
NOTE: Please read steps 2 through 4
completely before proceeding. Highlight or
write down the codes and device you wish to
program before starting step 2.
2. On the remote control, press DVD. Next,
press and hold SET until the LED (red
light) blinks twice, then release SET.
3. Use the “Setup Codes for DVD/VCR
Combos (Códigos de Configuración
para Aparatos Combinados DVD/
Videograbadora)” (on page 36) to
locate the brand name and then enter
the first four-digit code for your device.
If performed correctly, the LED will
blink twice.
NOTE: If the LED did not blink twice, repeat
steps 2 through 4 and enter the same code
again.
4. Aim the remote control at the device
and press POWER once. It should turn
off. If it does not, repeat steps 2
through 4, trying each code for your
brand until you find one that works. If
it still does not work, try “Searching for
Yo ur C od e” b el ow .
NOTE: If the device does not have a POWER
key, press the (PLAY) key.
5. If you’ve located a setup code that
works, but it also has a separate VCR
code, you’ll also n eed to program it into
the remote control to access VCR
controls as follows:
a. Press VCR once. Then press and
hold the SET key until the LED
blinks twice.
b. Enter the VCR code for your DVD
Player/VCR Combo. If correct, the
LED will blink twice.
NOTE: If a separate VCR setup code is not
listed, you can use the VCR key to program a
separate VCR device or another device (see
“Re-assigning Device Keys” on page 11).
6. For future reference, write down the
working DVD Player/VCR combo code
in the below boxes:
DVD Player/VCR Code:
Brand Name:____________________
VCR Code (if used):
Brand Name:_____________________
SEARCHING FOR YOUR
CODE
If your device does not respond to the
remote control after trying all codes listed
for your brand, or if your brand is not listed
at all, try searching for your code. For
example, to search for a code for your TV:
1. On the remote control, press TV once.
2. Press and hold SET until the LED (red
light) blinks twice, then release SET.
3. Enter 9 9 1. The LED will blink twice.
4. Aim the remote control at the TV and
slowly alternate between pressing
POWER and TV. Stop when the TV turns
off.
8 Programming DVD Player/ VCR Combo
PVR 6 Owners Manual.fm Page 9 Monday, December 20, 2004 11:17 AM
OWNER’S MANUAL
NOTE: In the search mode, the remote control
will send IR codes from its library to the
selected device, starting with the most
popular code first.
5. To lock in the code, press and release
SET. The LED will blink twice.
6. To search for the codes of your other
devices, repeat steps 1 through 5, but
substitute the appropriate device key
for the device you are searching for.
CHECKING THE CODES
If you have set up the remote control using
the Searching For Your Code procedure (on
the previous page), you may need to find
out which four-digit code is operating your
equipment.
For example, to find out which code is
operating your TV:
1. On the remote control, press TV once.
2. Press and hold SET until the LED (red
light) blinks twice, then release SET.
3. Enter 9 9 0. The LED will blink twice.
4. To view the code for the first digit,
press 1 once. Wait 3 seconds, count the
LED blinks (e.g., three blinks = 3) and
write down the number in the leftmost
box in the TV code boxes on page 7.
NOTE: If a code digit is 0, the LED will not
blink.
5. Repeat step 4 three more times for
remaining digits. Use 2 for the second
digit, 3 for the third digit, and 4 for the
fourth digit. Write down the code
digits in the remaining TV code boxes
on page 7.
6. To check for codes of other devices,
repeat steps 1 through 5, but substitute
the appropriate device key for each
device you are checking. Write down
the device’s code digits in the
appropriate code boxes on page 7.
PROGRAMMING MASTER
POWER
In its default state, the POWER key on the
URC-6131 remote control will individually
power your home entertainment devices on
or off. However, you can also program a
Master Power function onto the POWER key
that will sequentially turn on or off all the
devices with a single key press.
PROGRAMMING THE POWER KEY FOR
MASTER POWER
1. Press and hold SET until the LED (red
light) blinks twice, then release SET.
2. Enter 9 9 5. The LED will blink twice.
Then press POWER once.
3. For the first device you want in the
power on sequence, press its device
key (e.g., CBL/SAT) once.
4. Repeat step 3 up to five more times to
add desired devices to the power-on
sequence.
5. To save the settings and exit the
program, press and hold SET until the
LED blinks twice, then release SET.
OPERATING MASTER POWER
1. After programming, point the remote
control at the devices and press POWER
for at least 2 seconds to sequentially
turn on or off your devices.
NOTE: When you press POWER for less than 2
seconds, the remote will only send a power
command to the currently-selected device.
This allows you to still individually power
devices on or off.
Checking the Codes 9
PVR 6 Owners Manual.fm Page 10 Monday, December 20, 2004 11:17 AM
ONE FOR ALL 6-DEVICE PVR UNIVERSAL REMOTE CONTROL
2. You will see the devices turn on or off
according to your programmed
sequence.
NOTE: The currently-selected device will
always turn on first, followed by the
remaining programmed sequence. After the
master power sequence is complete, the
remote will control the first powered-on
device.
NOTE: If one or more devices does not have a
POWER key, the power off/on sequence may
be slightly delayed when the remote control
signals the device(s). This action is normal.
CLEARING MASTER POWER
1. Press and hold SET until the LED (red
light) blinks twice, then release SET.
2. Enter 9 9 5. The LED will blink twice.
Then press POWER once.
3. Press and hold SET until the LED blinks
twice, then release SET. Master Power is
now cleared.
1. Press and hold SET until the LED (red
light) blinks twice, then release SET.
2. Enter 9 9 4. The LED will blink twice.
3. For the source mode, press TV once.
4. For the source key, press VOL + once.
5. For the destination mode, press VCR
once.
6. For the destination key, press VOL +
once.
7. The LED will blink twice, indicating
the keymoved sequence is correct.
8. Repeat steps 1 through 7 twice more to
map remaining volume control keys,
substituting VOL - and MUTE as source
and destination keys in steps 4 and 6.
Upon completion of the above procedure,
you can now use your One For All 6-Device
PVR Universal Remote Control (URC6131nw) to control the TV’s volume and
MUTE in the VCR mode, as well as in the TV
mode.
USING KEYMOVER
The One For All 6-Device PVR Universal
Remote Control (URC-6131nw) includes a
Keymover feature that allows you to map (or
copy) keys from one mode (i.e., source
mode) to another mode (i.e., destination
mode).
NOTE: The following keys cannot be used as a
source or destination: TV, PVR, DVD, CBL/SAT,
AUD, VCR, and SET.
PROGRAMMING KEYMOVER
For example, if your VCR does not have
volume control, you can map those keys
(i.e., VOL +, VOL -, and MUTE) from the TV
mode to the VCR mode as follows:
10 Using Keymover
RESTORING KEYMOVED KEYS TO DEFAULT
SETTINGS
Restoring a Single Keymoved Key
1. Press a device key that has a keymoved
key.
2. Press and hold SET until the LED (red
light) blinks twice, then release SET.
3. Enter 9 9 4. The LED will blink twice.
4. Press the destination key twice (where
the keymoved key is stored). The LED
will blink twice.
Restoring All Keymoved Keys in a Single
Mode
1. Press and hold SET until the LED (red
light) blinks twice, then release SET.
2. Enter 9 9 4. The LED will blink twice.
PVR 6 Owners Manual.fm Page 11 Monday, December 20, 2004 11:17 AM
OWNER’S MANUAL
3. Press the destination mode twice
(where keymoved keys are stored). The
LED will blink twice.
RE-ASSIGNING DEVICE
KEYS
You can set the One For All 6-Device PVR
Universal Remote Control (URC-6131nw) to
control a second TV, PVR/DVR, VCR, DVD
player, or other device. For example, to
control a TV, a cable box, and two VCRs, you
will need to re-assign the unused DVD key to
operate the second VCR as follows:
1. On the remote control, press and hold
SET until the LED (red light) blinks
twice, then release SET.
2. Enter 9 9 2. The LED will blink twice.
3. Press VCR once, then press DVD once.
The LED will blink twice.
4. The DVD key is now ready to be
programmed for your second VCR. See
“Programming Device Control” on
page 6.
To re-assign other device keys to the DVD
key, repeat steps 1 through 4 with a
sequence from the below chart:
NOTE: Only one device can be assigned to an
unused device key at a time.
To Re -A ssi gn
Device
DVD as 2nd
TV key:
DVD as 2nd
CBL/SAT key:
DVD as 2nd
PVR key:
DVD as 2nd
AUD key:
Perform Sequence
SET - 9 - 9 - 2 - TV DVD
SET - 9 - 9 - 2 CBL/SAT - DVD
SET - 9 - 9 - 2 - PVR DVD
SET - 9 - 9 - 2 - AUD DVD
You can also re-assign another unused
device key by substituting it for the DVD key
above and performing the sequence. For
example, to re-assign an unused AUD key as
a second VCR key, perform SET - 9 - 9 - 2 -
VCR - AUD. When you’ve completed the reassignment, the LED will blink twice to
confirm your choice. At that time, you will
need to program the remote control for the
new device (see “Programming Device
Control” on page 6).
CHANGING VOLUME LOCK
The One For All 6-Device PVR Universal
Remote Control (URC-6131nw) is set at the
factory for independent volume control of
each selected device.
However, you may change the Volume Lock
setting to Global Volume Lock so that a
device’s volume will be locked to one mode
(e.g., to control TV volume in all other
modes). After that, if desired, you can
perform Individual Volume Unlock on a
selected device to set its volume control for
independent operation.
LOCKING VOLUME CONTROL TO ONE MODE
(GLOBAL VOLUME LOCK)
1. Press and hold SET until the LED (red
light) blinks twice, then release SET.
2. Enter 9 9 3 and then press any mode
key once (e.g., TV). The LED will blink
twice.
3. Now, when you press VOL +, VOL -, or
MUTE, the volume of the selected
device (e.g., TV) will be controlled
regardless of the mode you have
selected.
Re-assigning Device Keys 11
PVR 6 Owners Manual.fm Page 12 Monday, December 20, 2004 11:17 AM
ONE FOR ALL 6-DEVICE PVR UNIVERSAL REMOTE CONTROL
UNLOCKING VOLUME CONTROL FOR A
SINGLE DEVICE (INDIVIDUAL VOLUME
UNLOCK)
1. After performing Global Volume Lock
(see above), press a desired mode key
where you want volume to be unlocked
(e.g., AUD) and controlled within its
own mode.
2. Press and hold SET until the LED (red
light) blinks twice, then release SET.
3. Enter 9 9 3 and then press VOL - once.
The LED will blink four times.
4. If desired, repeat steps 1 through 3 (of
this section) for each device that you
want volume to be unlocked.
5. Now, after you select a device that has
volume unlocked (e.g., AUD), pressing
VOL +, VOL -, or MUTE, will control the
device’s volume only in its own mode.
UNLOCKING ALL VOLUME CONTROL
(RESTORING DEFAULT SETTING)
NOTE: Performing these instructions will
restore independent volume control for all
programmed devices (e.g., TV volume control
in TV mode, VCR volume in VCR mode, etc.).
1. On the remote control, press and hold
SET until the LED (red light) blinks
twice, then release SET.
2. Enter 9 9 3 and then press VOL + once.
The LED will blink four times.
3. Volume will again be independently
controlled according to its default
states for all programmed devices.
TROUBLESHOOTING
PROBLEM: LED (red light) does not
blink when you press a
key.
SOLUTION: Replace batteries with two
new AAA alkaline
batteries.
PROBLEM: LED blinks when you
press a key, but home
entertainment device does
not respond.
SOLUTION: Make sure the remote
control is aimed at your
home entertainment
device and is not farther
than 15 feet away.
PROBLEM: The unit does not control
home entertainment
devices or commands are
not working properly.
SOLUTION: Try all listed codes for the
device brands being set
up. Make sure they can be
operated with an infrared
remote control.
PROBLEM: DVD/VCR Combo does
not respond properly.
SOLUTION: Use the VCR codes for your
brand. Some combo units
may require both a DVD
code and a VCR code for
full operation.
PROBLEM: Changing channels does
not work properly.
12 Troubleshooting
PVR 6 Owners Manual.fm Page 13 Monday, December 20, 2004 11:17 AM
OWNER’S MANUAL
SOLUTION: If the original remote
control required pressing
ENTER to change channels,
then press ENTER on the
remote control after
entering the channel
number.
PROBLEM: Tried Searching For Your
Code method and still
could not find a working
code.
SOLUTION: Clear the device key as
follows: Press and hold SET
until the LED (red light)
blinks twice, then
release.Next enter 9 9 2.
Then press the device key
to be cleared twice.Now
repeat the Searching for
Yo ur C od e method on page
8.
PROBLEM: Remote control does not
turn on Sony or Sharp TV/
VCR Combo.
SOLUTION: For power on, these
products require
programming TV codes.
For Sony, use TV code 0000
and VCR code 0032. For
Sharp, use TV code 0093
and VCR code 0048.
PROBLEM: CH+ and CH- do not work
for your RCA TV.
SOLUTION: Due to RCA design (1983-
1987), only the original
remot e control will o perate
these functions.
PROBLEM: No remote control of
volume.
SOLUTION: See “Changing Volume
Lock” on page 11 to lock/
unlock volume.
ABOUT UPGRADING
The One For All 6-Device PVR Universal
Remote Control (URC-6131nw) has the
largest infrared code library available.
However, if you purchase a brand new home
entertainment device, it may not respond to
the codes stored in the remote control’s
memory.
If this happens, please contact our
Customer Support department (see
“Customer Support” on the next page) to
upgrade the remote control. The Customer
Support representative will search our
entire database for a code that matches your
device and instruct you how to enter it into
your One For All 6-Device PVR Universal
Remote Control (URC-6131nw).
If the code for your home entertainment or
home automation device is not in our
database, we will need to “capture” the code
for that device from its original remote
control. A new code would then be created
and need to be entered into your One For All
6-Device PVR Universal Remote Control
(URC-6131nw). If necessary, the Customer
Support representative can instruct you how
to begin the capture procedure.
NOTE: One For All reserves the right to
replace a returned remote control with a new
one of equal or superior functionality.
UPGRADE EXCLUSIONS
• Home entertainment devices
controlled by radio frequency (RF/
About Upgrading 13
Loading...