One for All 3032, 3034, URC-3030, 3033, 3031 User Manual

URC 3030

Easy 3

3031 / 3032 / 3033 / 3034

User Manual

Previous Model Name:

So Easy

Feature Function

RED Light (LED)

TV VCR CBL

POWER

The LED flashes red to show that the remote is working.

The TV, VCR and CBL keys are used to select the home entertainment device you want to control.

The POWER key operates the same as on your original remote.

Features and Functions

The illustration below and chart on the next page describe the features and functions of the One For All® Easy 3 Device

universal remote control.

Red Light (LED)

Setup

Key

TV Key

Volume

and

Channel

Glow Keys

Record

Key

Rewind

Key

Stop Key

POWERSETUP

VOL

PLAY

STOP

CBL

VOL

TV VCR

REC PAUSE

REW FF

Power Key

VCR Key

CBL Key

Mute

Glow Key

Pause Key

Fast Forward

Key

The SETUP key is used to set up your

SETUP

VOL

devices. The Glow Keys: VOL (Volume), CH

(Channel), and M (Mute) operate the same

as on your

VOL

original remote. To activate the "Glow" Feature, you must expose the Glow Keys to bright light. The length of time the Glow Keys remain illuminated will be determined by the length of time the remote is exposed to bright light. These keys are also used to enter set-up codes for your devices.

The REW (Rewind), FF (Fast Forward),

REW FF STOP

STOP, PLAY, PAUSE and REC (Record) keys control the same functions as those found on your VCR remote.

PLAY PAUSE REC

Overview:

Thank you for purchasing the One For All® Easy 3 Device universal remote. Before you can use your new

remote, you will need to program it. To do this, you need to tell the remote what equipment you wish to operate. This is done by following these three easy steps.

Step 1: Install two (2) new AAA alkaline batteries.

Step 2: Look up the code for your TV, VCR or Cable Box.

Step 3: Enter the code.

Play Key

Step 1:

Installing the Batteries

Step 3:

Setting Up Your Devices

Y our One For All alkaline batteries. T o install the batteries:

Easy 3 Device needs two (2) new AAA

On the back of the

One For All

Easy 3

Device, push down on the tab and lift the

cover off.

Match the batteries to the + and - marks inside the battery case, then insert the batteries.

Press the battery cover back into place.

POWER

Note: Removing the batteries for more than 30 minutes will require you to reprogram the remote control.

Step 2:

You will need one of these codes to program your One For All

Easy 3 Device remote.

Looking Up Your Electronic Device Code

Look at your Electronic Device to find out the brand name and write it in the space below:

TV ________________________

VCR _______________________

Cable _______________________

Set-Up Codes

RCA 1213 Sony 1111

1st TV code

2nd TV code

3rd TV code

1st VCR code

2nd VCR code

3rd VCR code

1st Cable code

2nd Cable code

3rd Cable Code

T est the unit by pressing PO WER. The red light (LED) should blink once.

Find your Device brand in the listing on the reverse side of these instructions. The most popular codes are listed first. Write your codes here:

1 2

Turn on your TV, VCR or Cable Box, depending on the device you are programming.

Press TV* and release. Press and hold SETUP until the One For All® Easy 3 Device's red

SETUP

POWER

PLAY

POWER

light blinks twice. Release SETUP.

* Note: When setting up your VCR and/or Cable Box,

substitute the appropriate device key (VCR or CBL).

Using the example shown on the right, enter the first four-digit code you wrote down for the device you are setting up. (See "Looking Up Your Electronic Device Code".) If you put in the code correctly, the red light will blink twice.

How to Enter Codes If your TV

Press code is:

3 4

TV Set Up

Aim the One For All® Easy3 Device at your TV and press POWER. Y our TV should turn off. If it doesn't, repeat Steps 2-4, trying each code listed for your brand until you find the one that operates your TV.

VCR Set Up

Aim the One For All® Easy3 Device at your VCR and press POWER. Y our VCR should turn off. If it doesn't, repeat Steps 2-4, trying each code listed for your brand until you find the one that operates your VCR. If your original VCR remote did not have a POWER key , put a tape in your VCR and press PLA Y on the One For All® Easy3 Device.

Cable Set Up

Aim the One For All® So Easy 3 Device at your Cable Box and press POWER. Your Cable Box should turn off. If it doesn't, repeat Steps 2-4, trying

each code listed for your brand until you find the one that operates your Cable Box. If your original Cable Box remote did not have a "ON" key, Use CH + on the One For All® Easy 3 Device to turn your Cable Box on.

VOL

+ 2 hidden pages