One digital solutions POP Digital User Manual

Safety and Warnings
Main Supply
This equipment is designed to operate from a 100-240 Volt, 50/60Hz AC main supply. The use of
other power sources may damage this equipment. Check that the voltage marked on the rating
plate located at the rear of the power adaptor states 100-240V. The manufacturer will NOT accept
responsibility for damage or injury caused by connecting to the wrong voltage.
This device complies with CE/FCC regulations.
Main Adaptor
The power adaptor supplied is compatible with a standard main socket. NB. If the power adap-
tor or lead gets damaged, it must be replaced by a qualied service agent with an approved
adaptor of the same type and rating.
Operation is subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) This device must accept any interference received, including interference
which may cause undesired operation. This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are de-
signed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio / TV technician for help. In accordance
with FCC requirements, changes or modications not expressly approved by
manufacturer could void the user’s authority to operate this product.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body
Dangerous voltage constituting a risk of electric shock is present inside this equipment.
This mark is applied to show the equipment conforms to European safety and
electro-magnetic compatibility standards.
There are important operating and maintenance instructions in the literature
accompanying this equipment.
Warning
• The main plug shall be the main disconnect device and shall remain operable
at all times.
Never let anyone push objects into holes and ventilation slots.
• Do not expose this product to dripping or splashing or place any objects lled
with liquids on or near the product.
• Do not place a naked ame source such as lighted candles on or near this product.
• Do not attempt to repair this product yourself; always get a qualied service agent
to carry out adjustments or repairs.
Overview
1. Hole for wall mount
2. The power socket: Power supply
3. LED indicator: charging status indicator
Components
Features
1. Six Cell Docking Station
2. Power Supply Unit
3. User Manual
1. Remove the 6 cell docking station from the package and place it on a desk.
2. Take out the power adaptor
3. Connect the power cable of the adaptor to the docking station
4. Connect the adaptor to the electricity
Important note:
• LED indicators (when a battery is in the compartment)
When LED indicator is Red , the battery is being charged.
When LED indicator is Green, the battery is fully charged.
When LED indication is Blinking Red, the compartment temperature is too high,
please take out the battery and wait for a short while. Afterwards return the
battery back for regular charging.
• The battery life will be decreased if the environment temperature is over 45 Celsius.
• When the battery is fully charged, do not leave it in the docking station as it will reduce
the battery life.
• Battery Charging time is approx. 5.5 hours.
Quick Start
Operating Instructions
4-5 hours.
Power Adaptor: Input 100-240V 50/60Hz, 1.8A
Output 12V , 12000mA.
Charging time
Power Supply Unit
Troubleshooting
Specications
Problem Troubleshooting
LED indicator is off
1. Make sure the charging unit is connected to
power supply
2. Make sure the battery is inserted to the charging
unit in the right direction
Loading...