Page 1
OWNER’S MANUAL
WINGLINK APP (iOS)
The ONE CONTROL WINGLINK provides easy connection and control with the One Control OC10W
Crocodile Tail Loop Wing.
- Homepage
Homepage provides the link/delink function with devices around the OC10W. Click “DEVICE”, then
choose device “Crocodile Tail Loop Wing” to connect, making sure the Bluetooth on both OC10W and
iPhone/iPad are on.
There are 4 subpages,
i. CONFIG for general setup
ii. PRESET edit
iii. ME for presets backup/restore
iv. FS map, tutorial for amp switching
- CONFIG Page
i. MIDI channel mode setup - The OC10W has 16 MIDI message groups, and each group contains
a PRECC#, a PC# and a CC#. Different modes assign different groups into a channel.
a) Standard (STD) mode - 16 channels (1 to 16), each channel is assigned 1 PRE CC#,
1PC#, 1CC#.
b) Professional 1 (PRO1) mode - organized in 8 channels (1 to 8), each channel is
assigned 2 PRE CC#, 2 PC# and 2 CC#.
c) Professional 2 (PRO2) mode - organized in 4 channels (1 to 4), each channel is
assigned 4 PRE CC#, 4 PC# and 4 CC#.
Page 2
ON Button: The ON button turns on/off a MIDI group. When a group is turned off, all the messages (PRE
CC#, PC#, CC#) will not be sent.
PRE CC#: This is a value fixed (always 127) control change number. The controller can be edited, it is
usually for a preset engage or tap tempo control, for example, assume a pedal is engaged by controller
number 102, then assign number 102 to the PRE CC#, OC10W will send CC# 102 and 127. For some
devices, 93 is the number of tap tempo control - assign 93 to the PRE CC#, OC10W will send CC# 93 and
127 to tap tempo the device by stomping the OC10W PROGRAM switch. The range of PRE CC# is 0~127
or OFF, OC10W doesn’t send PRE CC# on the specified midi channel when PRE CC# is set to “OFF”.
MIDI THRU: Turns on/off MIDI Thru. When MIDI thru is on, the MIDI output jack will output what
it receives.
Page 3
- PRESET Page
Preset page edits loops, footswitches, and MIDI in a preset. It also provides an instant backup function.
Scroll up/down BANK and PGM number to choose a preset, and press “SELECT” button to read it.
Take BANK A1 PGM 2 as an example - the page will show the preset, and the user can set LOOP1~10
and FS1~3 by pressing the round buttons.
Edit the preset name, maximum 5 letters.
Page 4
Scroll up/down a MIDI channel - edit PC# and CC#, check the validity by pressing the “CHECK’
button, the MIDI output jack will send PC# and CC# once when pressed. In PRO1 mode, the MIDI
channel 1 contains group 1A and 1B, MIDI channel 2 contains 2A+2B, etc. In PRO 2 mode, the MIDI
channel 1 contain 1A, 1B, 1C, 1D, channel 2 contains 2A, 2B, 2C, 2D, etc.
Save/update the preset into the backup file - Scroll to “SAVE TO NEW FILE” to find an existing file,
click “SAVE” button to update current preset in the backup file, or if there isn’t an backup file, generate
a new file to save the preset.
- ME Page
This page is for data backup and restore - all the presets can be saved into the phone or restore from the
phone. WINGLINK organizes presets in a full bank as a backup file. Scroll the BANK bar to find the bank
(A,B,C,D,E,F), scroll the name bar to find the backup file, and hit“SAVE” – Read data from OC10W and
Page 5
save to the phone. “RESTORE” – Restore the backup file to OC10W. To save a new backup file, just scroll
the file bar to “NEW FILE” and click “SAVE”, name it and save.
“FILE MANAGEMENT” is to manage the backup files, rename, delete a backup file.
“FACTORY RESET” – Erases all the data in OC10W and restores the unit to factory default settings. Click
the bar, then go to the device, use UP/DOWN button to choose “Y”, then press ENTER button to start the
reset.
- FS MAP Page
This is a tutorial page which shows the diagram of footswitch connection with amps.
Loading...