IMPORTANT SAFETY INSTRUCTIONS PARTS ENCLOSED:
• These instructions are provided for your safety. It is important that they are read carefully and
completely before installing the chandelier.
• THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH APPLICABLE
INSTALLATION CODES BY A PERSON FAMILIAR WITH THE CONSTRUCTION
AMD OPERATION OF THE PRODUCT AND THE HARZARDS INVOLVED.
• We strongly recommend that an authorized and certified electrician install all direct wire fixtures.
• This fixture has been rated from 6 x 40watt Max E12 standard bulb(not included).To avoid the
risk of fire, do not exceed the recommended wattage.
• The light fixture is meant for indoor use. DRY LOCATION ONLY. It must be connected only to 3-wire.
Single-phase electrical systems (provided with Ground wire or equivalent protection system).
• Keep it away from children.
(A)Wire Connectors (3)
(B) Mounting Bar (1)
(C) Mounting screw (2)
(D)Green Ground Screw (1)
(E)Canopy & Chain (1)
(F) Link Lock (2)
(G) Collar Loop (1)
(H)Wood Cover (1)
(I)Lamp Arm (6)
(J) Socket (6)
(K) Wood Chain (6)
(L) Bottom Assembly (1)
WARNING: TOOLS REQUIRED:
• Turn-off electricity supply at main circuit panel before installing. Do not connect electricity supply until your
chandelier is fully assembled and installed.
• To reduce the risk of fire, electrical shock, or personal injury, always turn off the chandelier and allow it to
cool
Prior to replacing light bulb. Do not touch bulb when fixture is turned on or look directly at light bulb.
• Keep flammable materials away from light bulb.
· Philips screwdriver
· Electrical tape
· Wire cutters
PRE-ASSEMBLY:
• Remove all parts and hardware from box along with plastic protective packaging. Do not discard any
contents until after assembly is complete to avoid accidentally discarding small parts or hardware.
• For your safety and convenience, assembly by two people is recommended
TO ASSEMBLY:
SHUT OFF THE MAIN ELECTRICAL SUPPLY FROM THE MAIN FUSE BOX/CIRCUIT BREAKER.
1. Carefully unpack all parts and hardware and lay out on a clear workspace.
2. Twist the Woodern cover(H) and bottom assembly(L) onto the lamp body,and lock on collar
loop
3. Open the lamp arm (I),Adjust the balance,then hang up the wood chain(K)
4. Attach the mounting bar(B) to the outlet box by inserting the supplied mounting screws(C)
5.Gently pull the wiring from the outlet box and allow wires to hang.
6.Carefully inspect the fixture’s wires. The NEUTURAL FIXTURE WIRE is marked with ‘N’.
The Hot FIXTURE WIRE is marked ‘L’. The unmarked GREEN wire is GROUND WIRE.
7. Attach the GROUND WIRE from the fixture to the GROUND JUNCTION BOX WIRE
from the outlet (usually green or bare wire). Fasten each together with a plastic wire connector
(A) and wrap the connection with electrical tape. Be sure that no wire strands are exposed. If your
outlet box DOES NOT have a GROUND WIRE, be sure to insert the Green Ground Screw (D)
into the mounting Bar (B) facing DOWN. Wrap the fixture’s GROUND WIRE around the ground
screw. IT IS IMPERATIVE THAT THE OUTLET BOX IN YOUR HOME IS PROPERLY
GROUNDED.
8. Connect the NEUTRAL FIXTURE WIRE to the NEUTRAL JUNCTION BOX WIRE
(white). Fasten each together with a wire connector (A) and wrap the connection with electrical
tape. Be sure no wire strands are exposed.
9. Connect the HOT FIXTURE WIRE to The HOT JUNCTION BOX WIRE (black). Fasten
each together with a wire connector (A). Be sure no wire strands are exposed. DO NOT
REVERSE THE HOT AND NEUTRAL CONNECTIONS OR SAFETY WILL BE
COMPROMISED.
CARE INSTRUCTIONS
:
10. Gently tuck the wire connection neatly into the ceiling junction box.
1. Make sure that power is turned off and bulb has cooled before
handling.
2.Wipe clean with a dry cloth/mid soapy solution. Do not use corrosive
cleaners.
3.The cable/cord of the chandelier cannot be replaced. If the cable is
damaged, do not use the light.
11. Move the canopy (E) up to the ceiling, and affix it with the ring knob on the chain. Ensure that
it is the chain and not the power cord that is supporting the fixture’s weight.
12. Install the bulb (Bulbs not included).
Loading...