Omron E3F2-7C4-M1-S, E3F2-7B4-S 2M, E3F2-7C4-S 2M, E3F2-7B4-M1-S, E3F2-R4B4-S-E 2M Datasheet

Cylindrical photoelectric sensor in M18 stainless steel housing

E3F2-SUS

The stainless steel housing provides enhanced
detergent resistance and longer lifetime in demanding
environments.

• Complete sensor portfolio in robust stainless steel
housing

• IP67, IP69K for highest water resistance

• Enhanced detergent resistance (ECOLAB certified)

• High power LED to compensate for dirt and misalign­ment

Selection Guide

Sensing method Sensing

Through-beam 7 m

Retro-reflective with M.S.R.

Diffuse-reflective 0.1 m (fixed,

Diffuse-reflective
(background suppression)

*1.

Pre-wired connectors are available on request. Contact your OMRON representative.

*2.

Order reflector separately

*3.

Measured with E39-R1S

Note: Standard cable length is 2 m. Models provided with a 5 m long cable are available. When ordering, specify the cable length by adapting the length of the cable

(e.g. E3F2-R4B4-S-E 5M). For other cable length please contact your OMRON sales representative.

*2

distance

0.1 to 4 m
(adjustable)

wide beam)

0.3 m
(adjustable)

0.1 m (fixed)

Connection method Order code

––2 m–

–  ––

––2 m–

*3

–  ––

––2 m–

–  ––

––2 m–

–  ––

––2 m–

–  ––

*1

*1

*1

*1

*1

*1

*1

*1

*1

*1

PNP output NPN output

E3F2-7B4-S 2M E3F2-7C4-S 2M

E3F2-7B4-M1-S E3F2-7C4-M1-S

E3F2-R4B4-S-E 2M E3F2-R4C4-S-E 2M

E3F2-R4B4-M1-S-E E3F2-R4C4-M1-S-E

E3F2-DS10B4-S 2M E3F2-DS10C4-S 2M

E3F2-DS10B4-M1-S E3F2-DS10C4-M1-S

E3F2-DS30B4-S 2M E3F2-DS30C4-S 2M

E3F2-DS30B4-M1-S E3F2-DS30C4-M1-S

E3F2-LS10B4-S 2M E3F2-LS10C4-S 2M

E3F2-LS10B4-M1-S E3F2-LS10C4-M1-S

1E3F2-SUS

Accessories (Order separately)

Name Sensing distance (typical)
Reflectors 4 m [100 mm] E39-R1S 60 x 40 mm

3 m [100 mm] E39-R48 60 x 40 mm, enhanced

5 m [100 mm] E39-R7 ∅ 84 mm
6 m [100 mm] E39-R8 100 x 100 mm
5 m [100 mm] E39-R40 80 x 80 mm

Tape Reflectors 0.7 m [150 mm] E39-RS1 35 x 10 mm

1.1 m [150 mm] E39-RS2 35 x 40 mm

1.4 m [150 mm] E39-RS3 80 x 70 mm
Lens Cap E39-F31
Mounting Bracket Y92E-B18 screw mount

*1.

Values in parentheses indicate the minimum required distance between the sensor and reflector.

Note: For detailed information about Accessories, refer to the main chapter “Accessories” at the end of the document.

*1

Model Remark

chemical resistance

Sensor I/O Connectors

Cord Shape Cable type Model
Standard Straight 2 m Four-wire type,

5 m XS2F-D421-G80-A

M12 connector

L-shaped 2 m XS2F-D422-D80-A

5 m XS2F-D422-G80-A

Detergent resistant cable with
SUS nuts

Straight 2 m Y92E-S12PVC4S2M-L

5 m Y92E-S12PVC4S5M-L

L-shaped 2 m Y92E-S12PVC4A2M-L

5 m Y92E-S12PVC4A5M-L

XS2F-D421-D80-A

2 Standard Photoelectric Sensors

Specifications

Ratings

Item E3F2-7# E3F2-R4#-# E3F2-DS10# E3F2-DS30# E3F2-LS10#4-#
Sensing method Through-beam Retro-reflective Diffuse-reflective

Wide beam (fixed) Potentiometer

adjustment
Power supply voltage 10 to 30 V DC
Current consumption 50 mA max. 30 mA max. 25 mA max. 30 mA max.
Sensing distance 7 m 0.1 to 4 m

(with E39-R1S)

Standard object Opaque:

11 mm dia. min.

Opaque:
56 mm dia. min.

0.1 m
(5 x 5 cm white
mat paper)

–

0.3 m

(10 x 10 cm white

mat paper)

Directional angle 3° to 20° 3° to 20° –
Differential travel

– 20% max. 5% max

(hysteresis)
Black/white error – 3% max
Response time Operation and Re-

1 ms max 2.5 ms max. 1 ms max.

set:

2.5 ms max.
Control output Transistor (open collector), load current: 100 mA max. (residual voltage: 2 V max.)
Power reset time 50 ms 100 ms max. 50 ms 100 ms
Ambient illumination Incandescent lamp:3000 lx max. / Sunlight:10000 lx max.
Ambient temperature Operating: -25 to 55 °C / Storage: -30 to 70 °C (with no icing or condensation)
Ambient humidity Operating: 35% to 85% / Storage: 35% to 95% (with no condensation)
Insulation resistance 20 MΩ min. at 500 V DC between energized parts and case
Dielectric strength 1000 VAC max., 50 / 60 Hz for 1 min between energized parts and case
Vibration resistance 10 to 55 Hz, 1.5 mm double amplitude for 2 hrs each direction (X, Y, Z)
Shock resistance Destruction: 500 m/s
Degree of protection

*1

IEC 60529 IP67, IP69K after DIN 40050-9

Light source (wave length) Infrared LED

2

each direction (X, Y, Z)

Red LED (660 nm) Infrared LED (880 nm) Red LED (660 nm)

(950 nm)

Indicators Light

incident / power in-

Light incident (red) /
stability (green)

Light incident / power indicator for light

source (red)
dicator for light
source (red)

Sensitivity adjustment Fixed Adjustable Fixed Adjustable Fixed
Connection method 2 m, 5 m pre-wired cable (PVC, dia. 4 mm (18 / 0.12)) or M12-connector
Operation mode Light-ON or Dark-ON selectable by wiring
Weight

(approx.)

Pre-wired (2 m) 180 g 90 g

Connector 120 g 50 g
Circuit protection Output short-circuit and power supply reverse polarity
Material Lens PMMA

*1.

Housing Stainless steel

The IP69k test according to DIN 40 050 part 9 is intended to simulate high pressure/steam cleaning. During the test 14-16l/min water at 80°C is sprayed onto the
sensor from different angles with 8000-10000kPa. The sensor may not suffer any damaging effects from high pressure water in appearance and functionality.

*2.

Material-specification for stainless steel housing case: 1.4305 (W.-No.), 303 (AISI), 2346 (SS). For other stainless steel materials please contact your OMRON
sales representative.

*2

Background
suppression

0.1 m
(10 x 10 cm white
mat paper)

Output
indicator
(orange) / stability
(green)

3E3F2-SUS

Engineering Data (Typical)

Operating Range (typical)

Through-beam Models
E3F2-7#4-#

Diffuse-reflective Models
E3F2-DS30#4-#

40

Sensitivity adjusted to maximum
Sensitivity adjusted to 400 mm

30

20

10

white paper

(100 x 100 mm)

Distance X (mm)

Distance Y (mm)

0

–10

–20

–30

–40

Sensing distance adjustable
between 0 and 550 mm

Object

Y

X

100 200 300 400 500 6000

Retro-reflective Models
E3F2-R4#4#-#

250

Typical sensing distance
E39-RS3
E39-R1S

200

E39-R40
E39-R7

150

E39-R8

100

50

0

-50

Distance Y (mm)

- 100

- 150

- 200

- 250
01 23456 789

Reflector

Y

X

Distance X (m)

Diffuse-reflective Models
E3F2-DS10#4-# (wide-beam type)

15

10

5

0

–5

Distance Y (mm)

–10

–15

Object

Y

X

20 40 60 80 100 1200

Distance X (mm)

white paper

(50 x 50 mm)

140

Excess Gain Ratio vs. Distance (typical)

Through-beam Models
E3F2-7#4-#

100

10

Excess gain

1

0.1
2 4 6 8 10 120

Distance X (m)

Retro-reflective Models
E3F2-R4#4#-#

100

Reflectors:
E39-RS3
E39-R1S
E39-R40
E39-R7

10

Excess Gain

1

0.1
024 6 810

E39-R8

Distance X (m)

Diffuse-reflective Models
E3F2-DS10#4-# (wide beam type)

100

Sensing object:

10

Grey paper

Excess gain

1

(18% reflectivity)

0.1
20 40 60 80 100 1200

White paper
(90% reflectivity)

Distance X (mm)

50 x 50 mm

140

4 Standard Photoelectric Sensors

Diffuse-reflective Models
E3F2-DS30#4-#

100

10

Excess gain

1

Grey paper
(18% reflectivity)

0.1
200 400 600 800 10000

Sensitivity adjusted to maximum
Sensing object:
100 x 100 mm

White paper
(90% reflectivity)

Distance X (mm)

Light spot vs sensing distance Incline (left and right) Incline (up and down)

Background suppression Models
E3F2-LS#

6

4

2

Spot diameter(mm)

0

050100150

Distance(mm)

Object material vs sensing distance

Background suppression Models
E3F2-LS#

120

100

80

Sensing distance (mm)

60

Background suppression Models
E3F2-LS#

20,00%

10,00%

0,00%

-10,00%

Sensing Distence movement (%)

-20,00%

-40 -30 -20 -10 0 10 20 30 40

Incline Angle (˚)

Background suppression Models
E3F2-LS#

20,00%

10,00%

0,00%

-10,00%

Sensing Distence movement (%)

-20,00%

-40 -30 -20 -10 0 10 20 30 40

Incline Angle (˚)

40

20

0

White

Veneer

paper

Card­board

Black
paper

Black
rubber

SUS Mirror

surface

Material

5E3F2-SUS

Operation

Output Circuits

Structure of Sensor I/O Connector

Classification Wire color

Brown ➀

White ➁

DC

Blue ➂

Black ➃

PNP Output

Model

Connector
pin No.

Output
transistor status

–– –

Use

Power supply
(+V)

Mode selec­tion Lon/Don

Power supply
(0 V)

Output

Timing chart

1
2
3

4

XS2F-D42#-D80-#
XS2F-G42#-G80-#

Connection
method

Output circuit

Through-beam emitter

Power
indicator
(red)

Main
circuit

Connector Pin Arrangement

Brown
White
Blue
Black

Brown

1

Blue

3

1

2

4

3

10 to 30 VDC

0 V

E3F2-@B4-@
(except for

E3F2-LS10B4-@)

ON when light
is incident.
(Light-ON)

ON when light
is interrupted.
(Dark-ON)

Incident
Interrupted

Output
indicator
(red)

Output
transistor

Load
(relay)

Incident
Interrupted

Output
indicator
(red)

Output
transistor

Load
(relay)

OFF

OFF

Operate
Release

OFF

OFF

Operate
Release

ZD: VZ = 36 V

1

2

4

3

Z

: VZ = 36 V

D

Brown

1

Z

D

Black

4

Blue

3

Pink

2

Brown

1

Black

4

Blue

3

Pink

2

Light
indicator

Connect the

ON

ON

ON

ON

pink (Pin ➁)
and brown (Pin
➀) cords or
open the pink
cord
(Pin ➁).

Connect the
pink (Pin ➁)
and blue
(Pin ➂) cords.

* Only on models

Light
indicator

Red

Green

E3F2-R4B4-@ and
E3F2-D1B4-@

Red

Green

Stability
indicator*

Main
circuit

Connector Pin Arrangement

Stability
indicator*

Main
circuit

100 mA
max.

Mode selection

100 mA
max.

Mode selection

10 to 30 VDC

Load

0 V

10 to 30 VDC

Load

0 V

Connector Pin Arrangement

* Only on models

E3F2-R4B4-@ and
E3F2-D1B4-@

1

2

4

3

6 Standard Photoelectric Sensors

Model

Output
transistor status

Timing chart

Connection
method

Output circuit

ON when light
is incident.
(Light-ON)

E3F2-LS10B4-@

ON when light
is interrupted.
(Dark-ON)

Note: Terminal numbers for connector type.

Incident
Interrupted

Output
indicator
(orange)

Output
transistor

Load
(relay)

Incident
Interrupted

Output
indicator
(orange)

Output
transistor

Load
(relay)

OFF

OFF

Operate
Release

OFF

OFF

Operate
Release

ZD: VZ = 36 V

1

2

4

3

Z

: VZ = 36 V

D

Brown

1

Z

D

Black

4

Blue

3

Pink

2

Brown

1

Black

4

Blue

3

Pink

2

Output
indicator

Connect the

ON

ON

ON

ON

pink (Pin ➁)
and brown (Pin
➀) cords or
open the pink
cord
(Pin ➁).

Connect the
pink (Pin ➁)
and blue
(Pin ➂) cords.

Output
indicator

Stability
indicator*

Orange

Green

Connector Pin Arrangement

Stability
indicator*

Orange

Green

Main
circuit

Main
circuit

100 mA
max.

Mode selection

100 mA
max.

Mode selection

10 to 30 VDC

Load

0 V

10 to 30 VDC

Load

0 V

Connector Pin Arrangement

1

2

4

3

7E3F2-SUS

NPN Output

Model

E3F2-@C4-@
(except for

E3F2-LS10C4-@)

E3F2-LS10C4-@

Output
transistor status

Timing chart

Connection
method

Output circuit

Through-beam emitter

Power
indicator
(red)

Main
circuit

––

ON when light is
incident.
(Light-ON)

ON when light is
interrupted. (Dark­ON)

ON when light is
incident.
(Light-ON)

ON when light is
interrupted. (Dark­ON)

Incident
Interrupted

Output
indicator
(red)

Output
transistor

Load
(relay)

Incident
Interrupted

Output
indicator
(red)

Output
transistor

Load
(relay)

Incident
Interrupted

Output
indicator
(red)

Output
transistor

Load
(relay)

Incident
Interrupted

Output
indicator
(orange)

Output
transistor

Load
(relay)

OFF

OFF

Operate
Release

OFF

OFF

Operate
Release

OFF

OFF

Operate
Release

OFF

OFF

Operate
Release

Connector Pin Arrangement

Output
indicator

Connect the

ON

ON

ON

ON

ON

ON

ON

ON

pink (Pin ➁)
and brown (Pin
➀) cords or
open the pink
cord
(Pin ➁).

Connect the
pink (Pin ➁)
and blue
(Pin ➂) cords.

Connect the
pink (Pin ➁)
and brown (Pin
➀) cords or
open the pink
cord
(Pin ➁).

Connect the
pink (Pin ➁)
and blue
(Pin ➂) cords.

* Only on models

Output
indicator

* Only on models

Output
indicator

Red

E3F2-R4C4-@ and
E3F2-D1C4-@

Red

E3F2-R4C4-@ and
E3F2-D1C4-@

Orange

Output
indicator

Orange

Stability
indicator*

Green

Connector Pin Arrangement

Stability
indicator*

Green

Connector Pin Arrangement

Stability
indicator*

Green

Connector Pin Arrangement

Stability
indicator*

Green

Connector Pin Arrangement

Main
circuit

Main
circuit

Main
circuit

Main
circuit

2

2

2

2

1

2

3

Z

: VZ = 36 V

D

1

3

Z

D

1

3

Z

D

1

3

Z

D

1

3

4

4

: VZ = 36 V

4

: VZ = 36 V

4

: VZ = 36 V

4

1

4

3

2

1

4

3

2

1

4

3

2

1

4

3

2

1

3

Brown

Black

Blue

Pink

Brown

Black

Blue

Pink

Brown

Black

Blue

Pink

Brown

Black

Blue

Pink

Brown

Blue

100 mA
max.

Mode selection

100 mA
max.

Mode selection

100 mA
max.

Mode selection

100 mA
max.

Mode selection

10 to 30 VDC

0 V

10 to 30 VDC

Load

0 V

10 to 30 VDC

Load

0 V

10 to 30 VDC

Load

0 V

10 to 30 VDC

Load

0 V

Note: Terminal numbers for connector type.

8 Standard Photoelectric Sensors

Dimensions Note: All units are in millimeters unless otherwise indicated

Cable type Connector type

Without potentiometer
E3F2-7#-S

E3F2-DS10#4-S
E3F2-LS10#4-S

E3F2-7#-M1-S
E3F2-DS10#4-M1-S
E3F2-LS10#4-M1-S

42.3
37

4

With potentiometer
E3F2-DS30#4-S

E3F2-R4#4-S

49.3

42.3
37

4

64.9

64.9

4.8 dia

4 dia

Light indicator

M18x1 6g

4.8 dia

Sensitivity adjustor

Light indicator

M18x1 6g

16.4 dia

4 dia

optical
area

optical
area

16.4 dia

27.7

27.7

6.2

6.2

24

24

65.5

42.3

37

4

E3F2-DS30#4-M1-S
E3F2-R4#4-M1-S

65.5

49.3

42.3
37

4

76

76

4.8 dia

M12x1 6g

Light indicator

M18x1 6g

Sensitivity adjustor

Light indicator

M18x1 6g

optical
area

16.4 dia

4.8 dia

16.4 dia

M12x1 6g

optical
area

27.7

27.7

24

6.2

24

6.2

Accessories (Order Separately)

Reflectors

E39-R1
E39-R1S

Two, 3.5 dia.

5259.9

Material, reflective

surface: acrylic

Rear surface: ABS

E39-R7

40.3
34

7

1.6

7.5

8

2.7

7.4

4.5

84

9E3F2-SUS

Reflectors

for M3

E39-R8 E39-R40

9

100

92

8.7

84.5

77

Tape Reflectors

E39-RS3

Installation

Mounting Bracket
Y92E-B18

ffor M3

92

100

for M3

77

84.5

E39-RS1

35

80

0.6

10

4 x R1

Reflecting
surface

0.7

Adhesive
tape

E39-RS2

70

Adhesive tape side

4-R1

35

4 x R1

40

Reflecting
surface

0.7

Adhesive
tape

Lens Cap
E39-F31

Glass plate

Note:
Hexagon bolt: M5 x 32
Material: plastic

10 Standard Photoelectric Sensors

Metal rim Gasket

20 dia.

E3F2

4 max.

Safety precautions

! Warning

This product is not designed or rated for directly or
indirectly ensuring safety of persons. Do not use it for
such a purpose.

! Caution

Do not use the product with voltage in excess of the
rated voltage. Excess voltage may result in malfunc­tion or fire.

Never use the product with an AC power supply.
Otherwise, explostion may result.

When cleaning the product, do not apply a high-pres­sure spray of water to one part of the product. Other­wise, parts may become damaged and the degree of
protection may be degraded.

High-temperature environments may result in burn
injury.

Precautions for Safe Use

The following precautions must be observed to ensure safe
operation of the Sensor.

Operating Environment

Do not use the Sensor in an environment where explosive or
flammable gas is present.

Connecting Connectors

Be sure to hold the connector cover when inserting or removing
the connector. Be sure to tighten the connector lock by hand;
do not use pliers or other tools. If the tightening is insufficient, the
degree of protection will not be maintained and the Sensor may
become loose due to vibration. The appropriate tightening torque
is 0.39 to 0.49 N·m for M12 connectors.

Load

Do not use a load that exceeds the rated load.

Rotation Torque for Sensitivity Adjustment

Adjust with a torque of 0.05 N·m or less.

Modifications

Do not attempt to disassemble, repair, or modify the Sensor.

Outdoor Use

Do not use the Sensor in locations subject to direct sunlight.

Cleaning

Do not use thinner, alcohol, or other organic solvents. Otherwise,
the optical properties and degree of protection may be degraded.

Surface Temperature

Burn injury may occur. The Sensor surface temperature rises de­pending on application conditions, such as the surrounding tem­perature and the power supply voltage. Use caution when
operating or washing the Sensor.

Precautions for Correct Use

Do not use the Sensor in any atmosphere or environment that
exceeds the ratings.

Do not install the Sensor in the following locations.

(1)Locations subject to direct sunlight
(2)Locations subject to condensation due to high humidity
(3)Locations subject to corrosive gas
(4)Locations where the Sensor may receive direct vibration or

shock

Connecting and Mounting

(1)The maximum power supply voltage is 30 VDC. Before turning

the power ON, make sure that the power supply voltage does
not exceed the maximum voltage.

(2)Laying Sensor wiring in the same conduit or duct as high-volt-

age wires or power lines may result in malfunction or damage
due to induction. As a general rule, wire the Sensor in a sepa­rate conduit or use shielded cable.

(3)Use an extension cable with a minimum thickness of 0.3 mm

and less than 100 m long.
(4)Do not pull on the cable with excessive force.
(5)Pounding the Photoelectric Sensor with a hammer or other

tool during mounting will impair water resistance.
(6)Mount the Sensor using a bracket (sold separately).

Do not exceed a torque of 20.0 Nm when tightening mounting

nuts.
(7)Be sure to turn OFF the power supply before inserting or re-

moving the connector.

Cleaning

Never use thinner or other solvents. Otherwise, the Sensor sur­face may be dissolved.

Power Supply

If a commercial switching regulator is used, ground the FG (frame
ground) terminal.

Power Supply Reset Time

The Sensor will be able to detect objects 100 ms after the power
supply is tuned ON. Start using the Sensor 100 ms or more after
turning ON the power supply. If the load and the Sensor are con­nected to separate power supplies, be sure to turn ON the Sensor
first.

Turning OFF the Power Supply

Output pulses may be generated even when the power supply is
OFF. Therefore, it is recommended to first turn OFF the power
supply for the load or the load line.

Load Short-circuit Protection

This Sensor is equipped with load short-circuit protection, but be
sure to not short circuit the load. Be sure to not use an output cur­rent flow that exceeds the rated current. If a load short circuit oc­curs, the output will turn OFF, so check the wiring before turning
ON the power supply again. The short-circuit protection circuit will
be reset.

Water Resistance

Do not use the Sensor in water, rainfall, or outdoors.

2

11E3F2-SUS

WARRANTY

OMRON’s exclusive warranty is that the products are free from de­fects in materials and workmanship for a period of one year (or other
period if specified) from date of sale by OMRON.

OMRON MAKES NO WARRANTY OR REPRESENTATION, EX­PRESS OR IMPLIED, REGARDING NON-INFRINGEMENT, MER­CHANTABILITY, OR FITNESS FOR PARTICULAR PURPOSE OF
THE PRODUCTS. ANY BUYER OR USER ACKNOWLEDGES THAT
THE BUYER OR USER ALONE HAS DETERMINED THAT THE
PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF
THEIR INTENDED USE. OMRON DISCLAIMS ALL OTHER WAR­RANTIES, EXPRESS OR IMPLIED.

LIMITATIONS OF LIABILITY

OMRON SHALL NOT BE RESPONSIBLE FOR SPECIAL, INDI­RECT, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR
COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE
PRODUCTS, WHETHER SUCH CLAIM IS BASED ON CONTRACT,
WARRANTY, NEGLIGENCE, OR STRICT LIABILITY.

In no event shall responsibility of OMRON for any act exceed the in­dividual price of the product on which liability is asserted.

IN NO EVENT SHALL OMRON BE RESPONSIBLE FOR WARRAN­TY, REPAIR, OR OTHER CLAIMS REGARDING THE PRODUCTS
UNLESS OMRON’S ANALYSIS CONFIRMS THAT THE PROD­UCTS WERE PROPERLY HANDLED, STORED, INSTALLED, AND
MAINTAINED AND NOT SUBJECT TO CONTAMINATION, ABUSE,
MISUSE, OR INAPPROPRIATE MODIFICATION OR REPAIR.

SUITABILITY FOR USE

THE PRODUCTS CONTAINED IN THIS DOCUMENT ARE NOT
SAFETY RATED. THEY ARE NOT DESIGNED OR RATED FOR EN­SURING SAFETY OF PERSONS, AND SHOULD NOT BE RELIED
UPON AS A SAFETY COMPONENT OR PROTECTIVE DEVICE
FOR SUCH PURPOSES. Please refer to separate catalogs for OM­RON's safety rated products.

OMRON shall not be responsible for conformity with any standards,
codes, or regulations that apply to the combination of products in the

customer’s application or use of the product.
At the customer’s request, OMRON will provide applicable third party

certification documents identifying ratings and limitations of use that
apply to the products. This information by itself is not sufficient for a
complete determination of the suitability of the products in combina­tion with the end product, machine, system, or other application or
use.

The following are some examples of applications for which particular
attention must be given. This is not intended to be an exhaustive list
of all possible uses of the products, nor is it intended to imply that the
uses listed may be suitable for the products:

• Outdoor use, uses involving potential chemical contamination or
electrical interference, or conditions or uses not described in this
document.

• Nuclear energy control systems, combustion systems, railroad sys­tems, aviation systems, medical equipment, amusement machines,
vehicles, safety equipment, and installations subject to separate in­dustry or government regulations.

• Systems, machines, and equipment that could present a risk to life
or property.

Please know and observe all prohibitions of use applicable to the
products.

NEVER USE THE PRODUCTS FOR AN APPLICATION INVOLVING
SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING
THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO
ADDRESS THE RISKS, AND THAT THE OMRON PRODUCT IS
PROPERLY RATED AND INSTALLED FOR THE INTENDED USE
WITHIN THE OVERALL EQUIPMENT OR SYSTEM.

PERFORMANCE DATA

Performance data given in this document is provided as a guide for
the user in determining suitability and does not constitute a warranty.
It may represent the result of OMRON’s test conditions, and the users
must correlate it to actual application requirements. Actual perfor­mance is subject to the OMRON Warranty and Limitations of Liability.

CHANGE IN SPECIFICATIONS

Product specifications and accessories may be changed at any time
based on improvements and other reasons.

It is our practice to change model numbers when published ratings or
features are changed, or when significant construction changes are
made. However, some specifications of the product may be changed
without any notice. When in doubt, special model numbers may be as­signed to fix or establish key specifications for your application on
your request. Please consult with your OMRON representative at any
time to confirm actual specifications of purchased products.

DIMENSIONS AND WEIGHTS

Dimensions and weights are nominal and are not to be used for man­ufacturing purposes, even when tolerances are shown.

ERRORS AND OMISSIONS

The information in this document has been carefully checked and is
believed to be accurate; however, no responsibility is assumed for
clerical, typographical, or proofreading errors, or omissions.

PROGRAMMABLE PRODUCTS

OMRON shall not be responsible for the user’s programming of a pro­grammable product, or any consequence thereof.

In the interest of product improvement, specifications are subject to change without notice.Cat. No. E59E-EN-01

OMRON EUROPE B.V.

Wegalaan 67-69,
NL-2132 JD, Hoofddorp,
The Netherlands
Phone: [phone]
Fax: [phone]
www.industrial.omron.eu

12 Standard Photoelectric Sensors