Omron E2E2-X2B1, E2E2-X2C1, E2E2-X5B1, E2E2-X10C1, E2E2-X10B1 Data Sheet

...
Long-barrel Inductive Proximity Sensor
E2E2
Proximity Sensor with a Long Screw Length
• Increased tightening strength. Cable protectors provided as a standard feature.
Be sure to read Safety Precautions on page 9.
Ordering Information
CSM_E2E2_DS_E_2_2
Sensors
DC 2-Wire Models
Model
Appearance Sensing distance
NO NC
Shielded
Unshielded
* Models with different frequencies are also available. The model numbers are E2E2-X@D15 (example: E2E2-X3D15).
DC 3-Wire Models
Appearance Sensing distance
Shielded
Unshielded
AC 2-Wire Models
Appearance Sensing distance
Shielded
Unshielded
M12 M18 M30 M12 M18 M30
M12 M18 M30 M12 M18 M30
M12 M18 M30 M12 M18 M30
3 mm
7 mm
10 mm
8 mm
14 mm
20 mm
2 mm
5 mm
10 mm
5 mm
10 mm
18 mm
2 mm
5 mm
10 mm
5 mm
10 mm
18 mm
E2E2-X3D1 2M * E2E2-X3D2 2M E2E2-X7D1 2M * E2E2-X7D2 2M E2E2-X10D1 2M * E2E2-X10D2 2M E2E2-X8MD1 2M * E2E2-X8MD2 2M E2E2-X14MD1 2M * E2E2-X14MD2 2M E2E2-X20MD1 2M * E2E2-X20MD2 2M
NO NC
E2E2-X2C1 2M E2E2-X2C2 2M E2E2-X5C1 2M E2E2-X5C2 2M E2E2-X10C1 2M E2E2-X10C2 2M E2E2-X5MC1 2M E2E2-X5MC2 2M E2E2-X10MC1 2M E2E2-X10MC2 2M E2E2-X18MC1 2M E2E2-X18MC2 2M
NO NC
E2E2-X2Y1 2M E2E2-X2Y2 2M E2E2-X5Y1 2M E2E2-X5Y2 2M E2E2-X10Y1 2M E2E2-X10Y2 2M E2E2-X5MY1 2M E2E2-X5MY2 2M E2E2-X10MY1 2M E2E2-X10MY2 2M E2E2-X18MY1 2M E2E2-X18MY2 2M
Operation mode
Model
Operation mode
Model
Operation mode
1
E2E2
Accessories (Order Separately)
Mounting Brackets Protective Covers Sputter Protective Covers
Ratings and Specifications
E2E2-X@D@ DC 2-Wire Models
Size
Shielding Shielded Unshielded Shielded Unshielded Shielded Unshielded
Item Model E2E2-X3D@ E2E2-X8MD@ E2E2-X7D@ E2E2-X14MD@ E2E2-X10D@ E2E2-X20MD@
Sensing distance 3 mm±10% 8 mm±10% 7 mm±10% 14 mm±10% 10 mm±10% 20 mm±10%
Set distance *1 0 to 2.4 mm 0 to 6.4 mm 0 to 5.6 mm 0 to 11.2 mm 0 to 8 mm 0 to 16 mm
Differential travel 10% max. of sensing distance
Sensing object
Standard sensing object
Response frequency *2
Power supply voltage (operating voltage range)
Leakage current 0.8 mA max.
Control output
Indicators
Operation mode (with sensing object ap­proaching)
Protection circuits Surge absorber, Load short-circuit protection
Ambient temperature Operating/Storage: 25 to 70°C (with no icing or condensation)
Ambient humidity Operating/Storage: 35% to 95% (with no condensation)
Temperature influence ±10% max. of sensing distance at 23°C in the temperature range of 25 to 70°C
Voltage influence ±1% max. of sensing distance at rated voltage in the rated voltage ±15% range
Insulation resistance 50 M min. (at 500 VDC) between current-carrying parts and case
Dielectric strength 1000 VAC, 50/60 Hz for 1 minute between current-carrying parts and case
Vibration resistance (destruction)
Shock resistance (destruction)
Degree of protection IEC IP67, in-house standard for oil resistance
Connection method Pre-wired Models (Standard cable length: 2 m)
Weight (packed state) Approx. 65 g Approx. 150 g Approx. 210 g
Materi­als
Accessories Instruction sheet
*1. Use the E2E2 within the range in which the setting indicator (green LED) is ON (except D2 Models). *2. The response frequency is an average value. Measurement conditions are as follows: standard sensing object, a distance of twice the standard sensing object, and
a set distance of half the sensing distance.
Switching capacity
Residual voltage 3 V max. (Load current: 100 mA, Cable length: 2 m)
Case Brass
Sensing surface PBT
Clamping nuts Nickel-plated brass
Toothed washer Zinc-plated iron
Ferrous metal (The sensing distance decreases with non-ferrous metal. Refer to Engineering Data on page 5.)
Iron, 12 × 12 × 1 mm
1 kHz 800 Hz 500 Hz 400 Hz 100 Hz
12 to 24 VDC (10 to 30 VDC), ripple (p-p): 10% max.
3 to 100 mA
D1 Models: Operation indicator (red) and setting indicator (green) D2 Models: Operation indicator (red)
D1 Models: NO D2 Models: NC
10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions
1,000 m/s
M12 M18 M30
Iron, 30 × 30 × 1 mm
Refer to the timing charts under I/O Circuit Diagrams on page 8 for details.
2
10 times each in X, Y, and Z directions
Iron, 18 × 18 × 1 mm
Iron, 30 × 30 × 1 mm
Iron, 30 × 30 × 1 mm
Iron, 54 × 54 × 1 mm
2
E2E2
E2E2-X@C@ DC 3-Wire Models
Size
Shielding Shielded Unshielded Shielded Unshielded Shielded Unshielded
Item Model E2E2-X2C@ E2E2-X5MC@ E2E2-X5C@ E2E2-X10MC@ E2E2-X10C@ E2E2-X18MC@
Sensing distance 2 mm±10% 5 mm±10% 5 mm±10% 10 mm±10% 10 mm±10% 18 mm±10%
Set distance 0 to 1.6 mm 0 to 4 mm 0 to 4 mm 0 to 8 mm 0 to 8 mm 0 to 14 mm
Differential travel 10% max. of sensing distance
Sensing object
Standard sensing object
Response frequency *1 1.5 kHz
Power supply voltage (op­erating voltage range) *2
Leakage current 13 mA max.
Control output
Indicators Operation indicator (red)
Operation mode (with sensing object ap­proaching)
Protection circuits Reverse polarity protection, Surge absorber, Load short-circuit protection
Ambient temperature Operating/Storage: 40 to 85°C (with no icing or condensation)
Ambient humidity Operating/Storage: 35% to 95% (with no condensation)
Temperature influence
Voltage influence ±1% max. of sensing distance at rated voltage in the rated voltage ±15% range
Insulation resistance 50 M min. (at 500 VDC) between current-carrying parts and case
Dielectric strength 1,000 VAC, 50/60 Hz for 1 minute between current carry parts and case
Vibration resistance (destruction)
Shock resistance (destruction)
Degree of protection IEC IP67, in-house standard for oil resistance
Connection method Pre-wired Models (Standard cable length: 2 m) and Connector Models
Weight (packed state) Approx. 75 g Approx. 160 g Approx. 220 g
Materi­als
Accessories Instruction sheet
*1. The response frequency is an average value. Measurement conditions are as follows: standard sensing object, a distance of twice the standard sensing object, and
a set distance of half the sensing distance.
*2. A full-wave rectification power supply of 24 VDC
Load current NPN open-collector output, 200 mA max. (55 VDC max.)
Residual voltage 2 V max. (Load current: 200 mA, Cable length: 2 m)
Case Brass
Sensing surface PBT
Clamping nuts Nickel-plated brass
Toothed washer Zinc-plated iron
Ferrous metal (The sensing distance decreases with non-ferrous metal. Refer to Engineering Data on page 5.)
Iron, 12 × 12 × 1 mm
12 to 24 VDC (10 to 55 VDC), ripple (p-p): 10% max.
C1 Models: NO C2 Models: NC
±15% max. of sensing distance at 23°C in the temperature range of 40 to 85°C ±10% max. of sensing distance at 23°C in the temperature range of 25 to 70°C
10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions
1,000 m/s
M12 M18 M30
Iron, 15 × 15 × 1 mm
400 Hz 600 Hz 200 Hz 400 Hz 100 Hz
Refer to the timing charts under I/O Circuit Diagrams on page 8 for details.
2
10 times each in X, Y, and Z directions
±20% (average value) can be used.
Iron, 18 × 18 × 1 mm
Iron, 30 × 30 × 1 mm
Iron, 30 × 30 × 1 mm
Iron, 54 × 54 × 1 mm
3
E2E2
E2E2-X@Y@ AC 2-Wire Models
Size
Shielding Shielded Unshielded Shielded Unshielded Shielded Unshielded
Item Model E2E2-X2Y@ E2E2-X5MY@ E2E2-X5Y@ E2E2-X10MY@ E2E2-X10Y@ E2E2-X18MY@
Sensing distance 2 mm±10% 5 mm±10% 5 mm±10% 10 mm±10% 10 mm±10% 18 mm±10%
Set distance 0 to 1.6 mm 0 to 4 mm 0 to 4 mm 0 to 8 mm 0 to 8 mm 0 to 14 mm
Differential travel 10% max. of sensing distance
Sensing object
Standard sensing object
Response frequency
Power supply voltage (op­erating voltage range) *1
Leakage current 1.7 mA max.
Control output
Indicators Operation indicator (red)
Operation mode (with sensing object ap­proaching)
Ambient temperature *1, 2 Operating/Storage: 40 to 85°C (with no icing or condensation)
Ambient humidity Operating/Storage: 35% to 95% (with no condensation)
Temperature influence
Voltage influence ±1% max. of sensing distance at rated voltage in the rated voltage ±15% range
Insulation resistance 50 M min. (at 500 VDC) between current-carrying parts and case
Dielectric strength 4,000 VAC, 50/60 Hz for 1 minute between current carry parts and case
Vibration resistance (destruction)
Shock resistance (destruction)
Degree of protection IEC IP67, in-house standard for oil resistance
Connection method Pre-wired Models (Standard cable length: 2 m) and Connector Models
Weight (packed state) Approx. 65 g Approx. 150 g Approx. 210 g
Materi­als
Accessories Instruction sheet
*1. When supplying 24 VAC to any of the above models, make sure that the operating ambient temperature range is at least −25°C to 85°C. *2. When using an M18 or M30 Connector Model at an ambient temperature between 70 and 85°C, make sure that the Sensor has a control output (load current) of 5
to 200 mA max.
Load current *2 5 to 200 mA 5 to 300 mA
Residual voltage Refer to Engineering Data on page 5.
Case Brass
Sensing surface PBT
Clamping nuts Nickel-plated brass
Toothed washer Zinc-plated iron
Ferrous metal (The sensing distance decreases with non-ferrous metal. Refer to Engineering Data on page 5.)
Iron, 12 × 12 × 1 mm
25 Hz
24 to 240 VAC (20 to 264 VAC), 50/60 Hz
Y1 Models: NO Y2 Models: NC
±15% max. of sensing distance at 23°C in the temperature range of 40 to 85°C, ±10% max. of sensing distance at 23°C in the temperature range of 25 to 70°C
10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions
1,000 m/s
M12 M18 M30
Iron, 15 × 15 × 1 mm
Refer to the timing charts under I/O Circuit Diagrams on page 8 for details.
2
10 times each in X, Y, and Z directions
Iron, 18 × 18 × 1 mm
Iron, 30 × 30 × 1 mm
Iron, 30 × 30 × 1 mm
Iron, 54 × 54 × 1 mm
4
Loading...
+ 8 hidden pages