Omnitron Systems Technology iConverter T1-E1 User Manual

Page 1
iConverteriConverter
®
iConverter
T1/E1 MUX/M
Managed T1/E1 Multiplexer
The iConverter T1/E1 MUX/M multiplexes up to sixteen T1 or
E1 circuits and one 10/100/1000 Ethernet service onto a ber optic transport link, and features remotely managed testing and conguration capabilities.
The iConverter T1/E1 MUX/M operates in a back-to-back conguration, and can be used in applications such as multiple T1/E1 extension, mobile backhaul and building-to-building PBX connectivity.
The T1/E1 copper interfaces are available in 4, 8, 12 or 16 RJ-48 port congurations for balanced T1/E1 applications. Optional adapter cables are available to convert each RJ­48 interface to a BNC interface for unbalanced E1 transport applications.
Key Features
Multiplexes up to sixteen independent T1 or E1 circuits ■ from copper links onto one ber link
10/100/1000 copper Ethernet service multiplexed with T1/E1 circuits
Small Form Pluggable (SFP) or xed ber transceivers, in standard and CWDM wavelengths
Supports multimode, single-mode dual ber and single- mode single-ber
Additional hot-swappable 4-Port T1/E1 MUX modules can be installed to increase system capacity up to 16 T1/E1 ports maximum per 1U (1.75 inch) chassis.
The T1/E1 MUX/M is available with xed-ber or Small Form Pluggable (SFP) transceivers, enabling easy adaptability to different ber types, distances and wavelengths. The T1/E1 MUX/M supports multimode, single-mode, single-mode single­ber in standard (850nm, 1310nm and 1550nm) and CWDM wavelengths.
The T1/E1 MUX/M features user-selectable local loop-back on both the copper and ber ports, remote ber loop-back and circuit test modes. These features facilitate testing of the remote unit, and minimize the need for test equipment and support personnel. Alarm relays and LEDs provide fault notication for loss of power, LOS and AIS.
Conguration of T1/E1 line codes, line build out, loopbacks and circuit test is accomplished via local serial port, Telnet, SNMP, or DIP-switches.
The 1U high iConverter T1/E1 MUX/M chassis can be mounted
in a 19-inch or 23-inch rack and features two load-sharing power supplies. It supports hot-swappable universal AC, 24VDC or 48VDC power supplies for power redundancy.
Remotely-managed conguration and testing enables
rapid deployment
Management via local serial port, Telnet, or SNMP
Congurable alarm relay contacts for audio/visual fault notication
Supports local and remote ber and copper loop-back
modes
Commercial (0 to 50º C ) and wide (-40 to 60º C) operating temperature ranges
Lifetime Warranty and free 24/7 Technical Support
Page 2
application
speciFications
Telecom Application: Mobile Backhaul
The following application shows an example of the iConverter
T1/E1 MUX/M used in a hybrid TDM/Ethernet transport network.
A wireless service provider has enhanced their network to
support 3G/4G services. The new equipment uses Ethernet for backhaul at the Cell Site, while their existing legacy 2G/2.5G equipment uses TDM (T1) for backhaul.
Using the iConverter T1/E1 MUX/M at the Cell Site, the service provider is able to multiplex up to 16 T1/E1 circuits and one 10/100/1000 Ethernet service on a common ber link. The ber carries the multiplexed trafc to a second iConverter
T1/E1 MUX/M that is installed at the Base Station Controller
(BSC) and Radio Network Controller (RNC). The T1/E1 MUX/M converts the legacy TDM trafc back to T1/E1 interfaces, where it is connected to the TDM network. The MUX also converts the Ethernet trafc back to a 10/100/1000 interface, where it is connected to the provider’s IP network.
Model Type
Protocols (TDM)
Protocols (Ether­net)
Frame Size 10,240 byte frames
Copper Connectors
Fiber Connectors
Dimensions W: 17.15” x D: 9.0” x H: 1.75”
Weight
Compliance UL, CE, FCC Class A, NEBS 3 Compliant
Humidity 5 to 95% (non-condensing)
Altitude -100m to 4000m
AC Power
24VDC Power
48VDC Power
Temperature
MTBF (hrs)
iConverter T1/E1 MUX/M
ANSI: T1.403, T1.102, AT&T: T62411, ITU: G.703, G.704, G.706, G.736, G.775, G.823, G.824, G.8261 ETSI: ETS 300 166
10BASE-T, 100BASE-TX, 1000BASE-T 100BASE-FX, 1000BASE-X
Ethernet: RJ-45 T1/E1: RJ-48
SFP Model: LC Dual Fiber Model: SC, ST Single-Fiber Model: SC
1 Power Supply: 7.5 lb 2 Power Supplies: 9.0 lb
Input Power Requirements:
Connector:
Input Power Requirements:
Connector:
Input Power Requirements:
Connector:
Standard: Wide: Storage:
16 Ports with Redundant AC or DC Power Supplies: 83,000
100 to 240VAC 50/60Hz
0.5A @ 120VAC
IEC320
18 to 36VDC
1.4A @ 24VDC
3-pin terminal
36 to 60VDC
0.7A @ 48VDC
3-pin terminal
0 to 50° C
-40 to 60° C
-40 to 80° C
iConverter T1/E1 MUX/M
Page 2
Page 3
ordering inFormation
2 4 x x - x - a b c
<Blank>
W
Standard Operating Temperature (0 to 50ºC)
Wide Operating Temperature (-40 to 60ºC)
1 One AC Power Supply
2 Two AC Power Supplies
3 One 48VDC Power Supply
4 Two 48VDC Power Supplies
5 One 24VDC Power Supply
6 Two 24VDC Power Supplies
1 One 4-Port MUX Module (4 ports total)
2 Two 4-Port MUX Modules (8 ports total)
3 Three 4-Port MUX Modules (12 ports total)
4 Four 4-Port MUX Modules (16 ports total)
Type Distance
Fiber Connector Type
ST SC SFP
Tx
[nm]
l
Rx
[nm]
l
Min. Tx Power
[dBm]
Max. Tx Power
[dBm]
Min. Rx Power
[dBm]
Max. Rx Power
[dBm]
Min
Attenuation
[dB]
SFP - - - 2439-0* - - - - - - - -
MM/DF 220/550m 2420-0 2422-0 - 850 850 -10 -4 -17 -3 - 7
SM/DF 12km 2421-1 2423-1 - 1310 1310 -9.5 -3 -19.5 -3 - 10
SM/DF 34km - 2423-2 - 1310 1310 -5 0 -23 -3 3 18
SM/DF 80km - 2423-3 - 1550 1550 -5 0 -23 -3 3 18
SM/DF 110km - 2423-4 - 1550 1550 0 5 -24 -3 8 24
SM/DF 140km - 2423-5 - 1550 1550 2 5 -28 -8 13 30
SM/SF 20km -
SM/SF 20km -
SM/SF 40km -
SM/SF 40km -
2430-1s
2431-1s
2430-2s
2431-2s
- 1310 1550 -9.5 -3 -20 -3 - 10.5
- 1550 1310 -9.5 -3 -20 -3 - 10.5
- 1310 1550 -3 0 -20 -3 3 17
- 1550 1310 -3 0 -20 -3 3 17
s When using single-ber (SF) media converter models, the Tx wavelength on one end has to match the Rx wavelength on the other. * Use 1250 Mbps (GigE, FC) SFP.
Consult Omnitron for other congurations.
Link
Budget
[dB]
Accessories
8220-9 Spare AC Power Supply
8226-9 Spare 24VDC Power Supply
8225-9 Spare 48VDC Power Supply
8485-4 Spare 4-Port T1/E1 MUX Module
9140-3 RJ-48 to BNC 3 ft Cable
9142-1 RJ-48 Alarm Breakout Cable
8092-2 23” (wide) Rack Mount Kit
©2010 Omnitron Systems Technology, Inc. All rights reserved. iConverter and NetOutlook are registered trademarks of Omnitron Systems Technology, Inc.
Trademarks are owned by their respective companies. Specications subject to change without notice.
091-12400-001F 9/10
800-675-8410 • 949-250-6510 • www.omnitron-systems.com • info@omnitron-systems.com • 140 Technology Dr. Irvine, CA 92618
iConverter T1/E1 MUX/M
Page 3
Loading...