Omnitron Systems Technology iConverter 1U Rack-Mount User Manual
7) INSTALLING ASSORTED UNITS TO THE SHELF
Any three types of assorted units can be mounted to the shelf.
In order to mount the module/chassis to the shelf, make sure the proper wall mount brackets
(not included) are installed on the module/chassis.
Shelf with Assorted Units
NOTE: Mounting the 2-Module chassis to the shelf requires 2U rack spacing.
1U 19” Rack Mount Shelf
User Manual
PRODUCT OVERVIEW
The 1U 19” rack mount shelf accommodates iConverter standalone media converters,
iConverter 1-Module chassis, iConverter 2-Module chassis and OmniConverter media
converters. Up to four iConverter standalone modules can be mounted to the shelf. Up to
three OmniConverters and/or iConverter 1-Module and up to two iConverter 2-Module
Chassis can be mounted to the shelf.
WARRANTY
This product is warranted to the original purchaser against defects in material and workmanship for a period of
TWO YEARS from the date of shipment. A LIFETIME warranty may be obtained by the original purchaser by
REGISTERING this product with Omnitron within 90 days from the date of shipment. TO REGISTER, COMPLETE
AND MAIL OR FAX THE ENCLOSED REGISTRATION FORM TO THE INDICATED ADDRESS. Or you may
register your product on the Internet at http://www.omnitron-systems.com. During the warranty period, Omnitron
will, at its option, repair or replace a product which is proven to be defective.
For warranty service, the product must be sent to an Omnitron designated facility, at Buyer’s expense. Omnitron
will pay the shipping charge to return the product to Buyer’s designated US address using Omnitron’s standard
shipping method.
Limitation of Warranty
The foregoing warranty shall not apply to defects resulting from improper or inadequate use and/or maintenance
of the equipment by Buyer, Buyer-supplied equipment, Buyer-supplied interfacing, unauthorized modications
or tampering with equipment (including removal of equipment cover by personnel not specically authorized and
certied by Omnitron), or misuse, or operating outside the environmental specication of the product (including
but not limited to voltage, ambient temperature, radiation, unusual dust, etc.), or improper site preparation or
maintenance.
No other warranty is expressed or implied. Omnitron specically disclaims the implied warranties of merchantability
and tness for any particular purpose.
Exclusive Remedies
The remedies provided herein are the Buyer’s sole and exclusive remedies. Omnitron shall not be liable for any direct,
indirect, special, incidental, or consequential damages, whether based on contract, tort, or any legal theory.
040-08260-001A 6/10
Omnitron Systems Technology * 140 Technology Dr. #500 * Irvine, CA 92618
949.250.6510 tel * 949.250.6514 fax * www.omnitron-systems.com
1U Rack Mount Shelf
INSTALLATION PROCEDURE
1) Unpack, Visual Inspection and Inventory
2) Rack Mounting
3) General Installation
4) Installing iConverter Standalone Wall Mount Modules to the Shelf
5) Installing iConverter 2-Module Chassis to the Shelf
6) Installing OmniConverter and iConverter 1-Module Chassis to the Shelf
7) Installing Assorted Units to the Shelf
1) UNPACKING, VISUAL INSPECTION AND INVENTORY
Review the contents. The following items should be included:
1U Rack Mount Shelf • User Manual•
20 Small Plastic Snap Rivets • 20 Large Plastic Snap Rivets•
(For mounting holes B & D) (For mounting holes A & C)
2) RACK MOUNTING
Mount and attach the shelf to the 19” standard rack using the appropriate rack mounting
screws (not included).
When rack-mounting the shelf, the rack should be appropriately earthgrounded.
The shelf provides NEBS ground posts to secure a grounding lug and wire from the rack to
the ground post.
Page 1
The shelf has multiple mounting holes to accommodate the different module/chassis options.
Use the Mounting Hole Guide to determine the correct mounting hole for the each unit
installed on the shelf.
Shelf with Mounting Holes
Shelf with iConverter Standalone Wall Mount Modules
5) INSTALLING iConverter 2-MODULE CHASSIS TO THE SHELF
Up to iConverter two 2-Module chassis can be mounted on the shelf.
In order to mount the iConverter 2-Module Chassis to the shelf, the optional wall mount
brackets (8249-0) must be installed on the chassis (not included).
Type
iConverter Standalone Wall Mount Module
iConverter Standalone Tabletop Module
w/Wall Mount Brackets (4381)
iConverter 1-Module Chassis
w/Wall Mount Brackets (8249-0)
iConverter 2-Module Chassis
w/Wall Mount Brackets (8249-0)
OmniConverter
Mounting Holes Rivet
A B C D Small Large
x x
x x
x x
x x
x x
Mounting Hole and Rivet Guide
3) GENERAL INSTALLATION
Use the Mounting Hole Guide to determine the correct mounting holes for the module/chassis
type. Align the module to the appropriate mounting holes starting at the bottom left corner
of the shelf and moving left to right across the shelf. Use the appropriate plastic snap rivets
to mount the module to the shelf by pressing the rivets through the top of the wall mount
bracket until the rivet locks into place.
Remove any rubber feet before installing the module/chassis to the shelf.
Cable tie downs slots are cut into the shelf to secure the power cord to the shelf using a
various types of cable ties (not included).
Grounding screws are available to attach a ground wire between the module and the shelf.
4) INSTALLING iConverter STANDALONE WALL MOUNT MODULES TO THE SHELF
Up to four iConverter standalone wall mount or tabletop modules can be mounted on the
shelf.
In order to mount the iConverter tabletop module to the shelf, the optional wall mount brackets
(4381) must be installed on the module.
Page 2 Page 3
Shelf with iConverter 2-Module Chassis
NOTE: Mounting the 2-Module chassis to the shelf requires 2U rack spacing.
6) INSTALLING OmniConverter AND iConverter 1-MODULE CHASSIS TO THE SHELF
Up to three OmniConverter media converters or iConverter 1-Module Chassis can be
mounted on the shelf.
In order to mount the iConverter 1-Module Chassis to the shelf, the optional wall mount
brackets (8249-0) must be installed on the chassis (not included).
Shelf with OmniConverter and iConverter 1-Module Chassis
Loading...