Omnitron Systems Technology FlexSwitch 6550 FK User Manual

FlexSwitchTM 1Fx+4U

Model 6550-FK

Replacement Kit

User Manual

140 Technology #500, Irvine, CA 92618

Phone: [phone]; Fax: [phone]

Table of Contents

1.0 INTRODUCTION.................................................................... 3

1.1 General Description ............................................................. 3

1.2 Chassis Models .................................................................... 3

2.0 INSTALLATION...................................................................... 4

2.1 Chassis Installation .............................................................. 4

2.2 Module Installation............................................................... 4

2.3 Fiber Installation ................................................................... 4

2.4 UTP Installation .................................................................... 4

3.0 CONFIGURATION ................................................................. 5

3.1 AC Site Preparation.............................................................. 5

3.2 AC Powered Chassis Mounting .......................................... 5

3.3 Configuring the DIP-Switches............................................. 6

3.3.1 4Tx Switch Module ............................................................... 6

3.3.2 Media Converter Module - Front Panel............................... 7

3.3.3 Media Converter Module - On-Board.................................. 8

4.0 LED INDICA TORS ................................................................. 9

4.1 4Tx Switch Module............................................................... 9

4.2 Media Converter Module ................................................... 10

5.0 SPECIFICATIONS................................................................ 11

6.0 LINK MODES....................................................................... 12

Page 2

1.0 INTRODUCTION

1.1 General Description

The 6550-FK is the direct replacement for the discontinued FlexSwitch
Model 600XC 1Fx + 4U. The 6550-FK replacement kit consists of one
iConverter 10/100Base-Tx to 100Base-Fx Media Converter Module and
one iConverter 4Tx Switch Module installed in a iConverter 2-Module
Chassis.

The 6550-FK provides auto-negotiating 10/100 UTP ports with auto-crossover
that enables easy attachment to hubs, switches and workstations. The
100Base-Fx fiber port supports half or full duplex operation.

The 6550-FK features on-board and front panel accessible DIP-Switches for
manual configuration of the ports.

1.2 Chassis Models

FlexSwitch Replacement Matrix

Discontinued Part Replacement Part

6550-0 6550-0-FK
6550-2 6550-2-FK
6550-3 6550-3-FK
6551-0 6551-0-FK
6551-2 6551-2-FK

Replacement Matrix

FlexSwitch Model 6550

Fiber Type Distance

MM 5km 6550-0-FK 6551-0-FK
SM 30km 6550-2-FK 6551-2-FK
SM 60km 6550-3-FK -

Model Numbers

Connector Type

SC ST

Page 3

2.0 INST ALLATION

2.1 Chassis Installation

The 6550-FK is designed to accommodate wall-mounting and tabletop
installations. For wall-mounting, the 8249-0 W all-Mount kit (sold separately)
is designed to attach the chassis to a wall, backboard or other flat surfaces.

For tabletop installations, place the unit on a flat level surface. Attach the
rubber feet to the bottom of the chassis to prevent the unit from sliding. Make
sure the unit is placed in a safe, dry and secure location.

For external power installation and configuration, see section 3.0.

2.2 Module Installation

The modules are pre-installed in the iConverter 2-Module chassis with the
backplanes enabled on both modules and Link Segment selected (see Section

6.0). If the modules are removed, carefully slide the module into the open
slot. Align the module with the installation guides and ensure that the module
is firmly seated against the backplane. Secure the module by fastening the
front panel thumbscrew (push in and turn clockwise to tighten) to the chassis
front.

2.3 Fiber Installation

Connect an appropriate multimode or single-mode fiber cable to the fiber port
of the installed module. It is important to make sure that the transmit (TX) is
attach to the receive side of the device at the other end and the receive (RX) is
attach to the transmit side.

2.4 UTP Installation

Connect the UTP ports via a Category 5 cable to a 10Base-T or 100Base-Tx
Ethernet device.

Page 4

3.0 CONFIGURATION

3.1 AC Site Preparation

• Power source should be available within 5 ft. of the chassis and installed

per the National Electrical Code ANSI/NFPA-70.

• This equipment requires a 100-240VAC, 0.5Amp, 50/60Hz power outlet.

Appropriate overloading protection should be provided on the AC power
source outlets utilized.

• The operating temperature of this equipment is 0 to 50 degrees C. If

installed in a closed or multi-module rack assembly , the operating ambient
temperature of the rack must not exceed the maximum rated 50 degrees C.

• Installation of the equipment should be such that the air flow in the front

and back of the chassis is not compromised or restricted.

• Never use this equipment to carry any weight except its own. Never use it

as a shelf to support the weight of other equipment.

3.2 AC Powered Chassis Mounting

Attach the AC power cord to the back of the Power Receptacle and plug into
the AC outlet. Any installed modules will illuminate the power LED.

Page 5