Omnitron Systems Technology FlexPoint 10T-2 User Manual

FlexPoint™ 10T/2 User Instructions

Description

The FlexPoint family of Converters supports the IEEE

802.3 and Ethernet Versions 1.0 / 2.0 standards. They
convert among 10BASE-FL with single-mode (SM) and
multimode (MM) fiber, 10BASE-2 thin coax and 10BASE-T
twisted pair (UTP) media types.

The FlexPoint 10T/2 provides conversion from 10BASE-2
coax to 10BASE-T UTP. It features coax connector and
an EIA/TIA 568 RJ45 UTP connector.

The FlexPoint 10T/2 supports switch selectable Straight­through or crossed RJ45 UTP wiring and a switch
selectable coax line termination.

Power Adapter Notice:

1. When used in a stand-alone configuration, this
product is intended to be used only with a Listed
Direct Plug-In Power Unit marked “Class 2” and
rated at 9VDC, 1 Amp.

2. This product should always be used only with its
enclosed Power Unit.

WARNING!

Before plugging the Power Adapter to any
wall outlet or AC power source, verify that the
power on the unit is appropriate for your AC
line voltage source.

Mounting:

The Omnitron FlexPoint 10T/2 can be individually
wall mounted using a wall-mounting kit, rack-mounted
using a 5-Module space-saver shelf or inserted in a
14-Module power-redundant FlexPoint Powered
Chassis. When wall-mounting or shelf-mounting,
attach the power adapter unit.

If connecting the UTP cable to a hub or switch, set
the cross-over switch to the straight position (factory
setting). If connecting to a PC or workstation, set the
switch to the cross-over position.

When connecting the FlexPoint 10T/2 at the end of a
coax segment, attach the coax cable directly into the
FlexPoint’s BNC coax connector. When connecting it
along the coax cable (not at the end), use a “T”
connector to tap into the cable.

Switch Settings:
“RJ45 Cross-Over” switch: When connecting the UTP

to a hub or switch, it should be se to “Straight-Through”
(factory setting). When connecting to a PC or workstation,
it should be set to “Cross-Over”.

“Termination” switch: When attaching anywhere along
a coax cable except at the end, the Termination switch
should be set to “Termination Out” (factory setting).
When attaching at the end of a cable, it can be set to
“T ermination In.” When the switch is set to “Termination
In”, an external termination must not be attached.

LED indicators:
LED Color Description

Power Yellow Power applied.
Jabber Red Jabber condition.
Coax Rx Green Received data on coax line.
Coax Col Yellow Collision on coax line.
UTP Rx Green Received data on UTP line.
UTP Col Yellow Collision on UTP line.
UTP Link Green Operational device detected at

the far end of UTP.

Polarity Yellow Polarity reversal was detected

and corrected automatically.

Technical Support:

If you encounter problems in installing or maintaining
this product, contact Omnitron Technical Support:

Phone: [phone]
Fax: [phone]
Address: Omnitron Systems Technology, Inc.

140 Technology Drive, #500

Irvine, CA 92618
Email: [e-mail]
URL: http://www.omnitron-systems.com

User Warranty Registration

Omnitron Systems Technology, Inc.

140 Technology Drive, #500

Irvine, CA 92618, USA

Fax: [phone]

Please register on-line @ http://www.omnitron-systems.com or complete both sides

and mail or fax this registration form to:

Name: _________________________________________________

Company: ______________________________________________

Address: ______________________________________________

Please complete both sides of this form

______________________________________________

City: ___________________ State: _______ Zip Code: ________

Country: _______________________________________________

Phone: ____________________ Fax: _______________________

E-mail:_________________________________________________

Warning

The operating description in this Instruction Manual is
for use by qualified personnel only. To avoid electrical
shock, do not perform any servicing of this unit other
than that contained in the operating instructions, unless
you are qualified and certified to do so by Omnitron
Systems Technology, Inc.

Caution

All user-required operations can be performed without
opening the unit. Never attempt to open or remove the
cover or tamper with the unit.

Warranty

This product is warranted to the original purchaser against
defects in material and workmanship for a period of TWO
YEARS from the date of shipment. A LIFETIME warranty
may be obtained by the original purchaser by
REGISTERING this product with Omnitron within 90 days
from the date of shipment. TO REGISTER, COMPLETE
AND MAIL OR FAX THE REGISTRATION PORTION OF
THIS INSTRUCTION MANUAL TO THE INDICATED
ADDRESS. Or you may register your product on the
internet at http://www.omnitron-systems.com. During
the warranty period, Omnitron will, at its option, repair or
replace a product which is proven to be defective.

For warranty service, the product must be sent to an
Omnitron designated facility, at Buyer’s expense. Omnitron
will pay the shipping charge to return the product to Buyer’s
designated US address using Omnitron’s standard shipping
method.

Limitation of Warranty

The foregoing warranty shall not apply to defects
resulting from improper or inadequate use and/or
maintenance of the equipment by Buyer, Buyer-supplied
equipment, Buyer-supplied interfacing, unauthorized
modifications or tampering with equipment (including
removal of equipment cover by personnel not
specifically authorized and certified by Omnitron), or
misuse, or operating outside the environmental
specification of the product (including but not limited to
voltage, ambient temperature, radiation, unusual dust,
etc.), or improper site preparation or maintenance.

No other warranty is expressed or implied. Omnitron
specifically disclaims the implied warranties of
merchantability and fitness for any particular purpose.

Exclusive Remedies

The remedies provided herein are the Buyer’s sole and
exclusive remedies. Omnitron shall not be liable for
any direct, indirect, special, incidental, or consequential
damages, whether based on contract, tort, or any legal
theory.

Form: 040-04320-000B 11/07

Notes:

____________________________
____________________________
____________________________
____________________________
____________________________
____________________________
____________________________
____________________________
____________________________
_____________________________
____________________________
____________________________
____________________________
____________________________
____________________________
____________________________

User Warranty Registration

Please register on-line @ http://www.omnitron-systems.com or complete both

sides and mail or fax this registration form to:

FlexPoint Type: __________________________________________

Model:_________________________________________________

Serial Number: ______________ Purchase Date: ______________

Purchased From: _________________________________________

Address: ______________________________________________

City: ___________________ State: _______ Zip Code: ________

Country: _______________________________________________

Comments and Suggestions: _______________________________

Please complete both sides of this form

______________________________________________________

______________________________________________________