Omnitron Systems Technology FlexPoint 10FL-T User Manual

FlexPoint™ 10FL/T User Instructions

ABOUT THIS MANUAL:

This document supports revision “Rev. 2” of the 10FL/T.
Please refer to the serial number label on the bottom
of the 10FL/T for the revision number of your product.
This revision incorporates the following improvements
to the 10FL/T:

1. 10FL/T operates in Link Propagate mode: A port of
the 10FL/T transmits a Link signal only when receiving
a Link at the other port.

DESCRIPTION:

The Omnitron FlexPoint 10FL/T media converter pro­vides 10BASE-FL single-mode (SM) or multimode (MM)

ber to 10BASE-T twisted pair (UTP) media conversion.

The 10FL/T is compliant with the IEEE 802.3 standards.

It features a pair of ST or SC ber connectors and an
EIA/TIA 568 RJ45 UTP connector.

These FlexPoint 10FL/T models are supported:

Model Fiber Type Max Distance Connector

4300 850 nm (MM) 2 km ST
4301 1310 nm (SM) 30 km ST
4302 1310 nm (MM) 5 km ST
4303 850 nm (MM) 2 km SC
4304 1310 nm (SM) 30 km ST
4306 1550 nm (SM) 85 km SC
4307 1550 nm (SM) 120 km SC

For other ber congurations, please consult factory.

The 10FL/T automatically supports Half-Duplex and Full­Duplex operations. It also supports switch-selectable

straight-through or crossed RJ45 UTP wiring.

POWER ADAPTER NOTICE:

1. When used in a standalone conguration, this product

is intended to be used only with a Listed Direct Plug-In

Power Unit marked “Class 2” and rated at 9Vdc, 1 Amp.

2. This product should always be used only with

Omnitron Supplied Power Unit model number 9113-PS
or 9115-PS.

WARNING!

Before inserting the Power Adapter, verify

that the power on the unit is appropriate for

your AC line voltage source.

MOUNTING:

The FlexPoint 10FL/T can be solo-mounted using a wall­mounting kit or DC Power Adapter. It can also be rack-

mounted using a 5-position shelf, or a 14-position, high-

density FlexPoint Powered Chassis. If wall-mounting or

shelf-mounting, attach the power adapter unit.

Attach the ber cables to the FlexPoint 10FL/T ST or

SC connectors. Note that the FlexPoint transmit (Tx)
must attach to the receive side on the device at the far

end of the ber and the receive (Rx) must attach to the

transmit side.

Both the ber and UTP ports must be connected in order

for the unit to establish an end-to-end link.

DIP-SWITCH SETTINGS:
UTP Crossover DIP-Switch:

When connecting the UTP cable to a hub or switch,

set the DIP-switch to straight-through “UTP Hub/
Switch” (factory setting). When connecting to a PC
or workstation, set the DIP-switch to crossover “UTP
to Workstation”.

Disable Auto-Negotiation and manually set port
speed to 10Mbps on the connecting UTP device.

LED INDICATORS:

LED Color Description

Power On Yellow Power applied
Polarity Yellow Polarity reversal was detected

Fiber Link Green Operational device detected at

Fiber Rx Green Received data on ber line
UTP Link Green Operational device detected at

UTP Rx Green Received data on UTP link

TECHNICAL SUPPORT:

If you encounter problems in installing or maintaining this

product, contact Omnitron Technical Support:
Phone: [phone]
Fax: [phone]
Address: Omnitron Systems Technology, Inc.

38 Tesla

Irvine, CA 92618 USA

E-mail: [e-mail]

URL: http://www.omnitron-systems.com

and corrected automatically

the far end of ber

the far end of UTP

User Warranty Registration

Omnitron Systems Technology, Inc.

38 Tesla

Irvine, CA 92618 USA

Fax: [phone]

Please register on-line @ http://www.omnitron-systems.com or complete both

sides and mail or fax this registration form to:

Name:___________________________________________________

Company:_______________________________________________

Address:_______________________________________________

_______________________________________________

Please complete both sides of this form

City: ___________________ State: _______ Zip Code: __________

Country:________________________________________________

Phone: ____________________ Fax: _________________________

E-mail:__________________________________________________

Warning

The operating description in this Instruction Manual is

for use by qualied personnel only. To avoid electrical
shock, do not perform any servicing of this unit other than
that contained in the operating instructions, unless you
are qualied and certied to do so by Omnitron Systems
Technology, Inc.

Caution

All user-required operations can be performed without
opening the unit. Never attempt to open or remove the
cover or tamper with the unit.

Warranty

This product is warranted to the original purchaser
against defects in material and workmanship for a period
of TWO YEARS from the date of shipment. A LIFETIME
warranty may be obtained by the original purchaser by

REGISTERING this product with Omnitron within 90 days
from the date of shipment. TO REGISTER, COMPLETE

AND MAIL OR FAX THE REGISTRATION PORTION OF

THIS INSTRUCTION MANUAL TO THE INDICATED

ADDRESS. Or you may register your product on the
internet at http://www.omnitron-systems.com. During

the warranty period, Omnitron will, at its option, repair

or replace a product which is proven to be defective.

For warranty service, the product must be sent to
an Omnitron designated facility, at Buyer’s expense.

Omnitron will pay the shipping charge to return the

product to Buyer’s designated US address using
Omnitron’s standard shipping method.

Limitation of Warranty

The foregoing warranty shall not apply to defects
resulting from improper or inadequate use and/or

maintenance of the equipment by Buyer, Buyer-supplied
equipment, Buyer-supplied interfacing, unauthorized
modications or tampering with equipment (including
removal of equipment cover by personnel not specically
authorized and certied by Omnitron), or misuse, or
operating outside the environmental specication of the
product (including but not limited to voltage, ambient
temperature, radiation, unusual dust, etc.), or improper

site preparation or maintenance.

No other warranty is expressed or implied. Omnitron
specifically disclaims the implied warranties of

merchantability and tness for any particular purpose.

Exclusive Remedies

The remedies provided herein are the Buyer’s sole and

exclusive remedies. Omnitron shall not be liable for

any direct, indirect, special, incidental, or consequential
damages, whether based on contract, tort, or any legal

theory.

Form: 040-04300-003G 10/13

Notes:

____________________________
____________________________
____________________________
____________________________
____________________________
____________________________
____________________________
____________________________
____________________________
_____________________________
____________________________
____________________________
____________________________
____________________________
____________________________
____________________________

User Warranty Registration

Please register on-line @ http://www.omnitron-systems.com or complete both

sides and mail or fax this registration form to:

FlexPoint Type:  10FL/T  10FL/2  10T/2  Other _______

Model: _________________________________________________

Serial Number: ______________ Purchase Date: ______________

Purchased From: _________________________________________

Address: ______________________________________________

City: ___________________ State: _______ Zip Code: ________

Country: _______________________________________________

Please complete both sides of this form

Comments and Suggestions: _______________________________

______________________________________________________

______________________________________________________