Omnitron Systems Technology FlexCeiver 10T User Manual

FlexCeiver™ 10T User Instructions
Description:
The FlexCeiver family of transceivers are compatible with IEEE 802.3 and Ethernet Versions 1.0 / 2.0. They enhance networking media connectivity using 10Base-FL with single-mode (SM) and multimode (MM) fiber, 10Base-2 thin coax and 10Base-T twisted pair (UTP).
All FlexCeivers have a 15-pin AUI connector that attaches to a mating AUI connector mounted on hosting Ethernet DTE equipment such as a workstation or a PC, or on a repeater such as a hub or a switch.
This FlexCeiver 10T model is described here:
Model Maximum Distance
4210 100 meters / 328 ft. The 4210 model provides a switch selectable full-duplex
operation that allows data to flow between two Ethernet switches or a PC and a switch in both directions simultaneously, doubling the 10 Mbps half-duplex Ethernet to 20 Mbps.
Wire polarity errors are automatically corrected by the FlexCeiver and the correction is indicated by an LED.
Mounting:
Insert the Omnitron FlexCeiver 10FL into the 15-pin AUI port on a PC, workstation, hub or switch; slide the connector latch locking it into place. If an AUI cable is used, it is limited to 50 meters (164 ft.). Attach a RJ45 equipped UTP category 3 or higher (4 or 5) cable to the 10T’s RJ45 connector. Note that the total length of the cable should not exceed 100 meters (328 ft.). The far end of the cable must connect to repeater equipment such as a hub or a switch. Connecting to another DTE type (PC) is possible via a crossover cable.
Switch Settings: “SQE” switch: When attaching to a PC (or a workstation),
the SQE switch should be set to “SQE Enable” (factory setting). When connecting to a hub or a switch, it should be set to “SQE Disable.”
“Duplex” switch: When attaching to a hub or a PC connected to a hub, the Duplex switch should be set to “Half Duplex” (factory setting). When attaching to an Ethernet switch or a PC (or workstation) attached to an Ethernet switch, the FlexCeiver can be set to “Full Duplex.” To take advantage of the 20 Mbps full duplex performance, the PC Network Interface Card (NIC) must also be set to “Full Duplex.”
LED indicators: LED Color Description
Transmit Green Transmitted data activity Receive Green Received data activity Link Active Green Operational device at the far
end
Jabber Err Red Attached host unit violated
transmission time, could indicate a faulty Network Interface Card (when attached to a PC).
Polarity Invert Yellow Correction activated for
reversed UTP wires SQE Enable Y ellow “SQE Enable” indicator Full Duplex Yellow “Full Duplex” indicator Collision Yellow Collision (normal operation)
Technical Support:
If you encounter problems in installing or maintaining this product, contact Omnitron Technical Support:
Phone: (949) 250-6510 Fax: (949) 250-6514 Email: support@omnitron-systems.com Address: Omnitron Systems Technology, Inc.
27 Mauchly #201 Irvine, CA 92618 USA
Please complete both sides of this form
User Warranty Registration
Omnitron Systems Technology, Inc.
27 Mauchly #201
Irvine, CA 92618 USA
Fax: (949) 250-6514
Please complete both sides and mail or fax this registration form to:
Name: _________________________________________________
______________________________________________
Company: ______________________________________________
Address: ______________________________________________
City: ___________________ State: _______ Zip Code: ________
Country: _______________________________________________
Phone: ____________________ Fax: _______________________
E-mail:_________________________________________________
__________________________________________________________
Comments and Suggestions: _________________________________
Country:__________________________________________________
City: ___________________ State: _______ Zip Code: __________
Address: ________________________________________________
Purchased From: ____________________________________________
Serial Number: ______________ Purchase Date: ________________
Model: __________________________________________________
FlexCeiver Type: S 10FL S 10T S 10B2 S Other ___________
the other side.
Please complete both sides and mail or fax this form to the address indicated on
The operating description in this Instruction Manual is for use by qualified personnel only. To avoid electrical shock, do not perform any servicing of this unit other than that contained in the operating instructions, unless you are qualified and certified to do so by
User Warranty Registration
Omnitron Systems Technology, Inc.
All user-required operations can be performed without opening the unit. Never attempt to open or remove the cover or tamper with the unit.
This product is warranted to the original purchaser against defects in material and workmanship for a period of TWO YEARS from the date of shipment. A LIFETIME warranty may be obtained by the original purchaser by REGISTERING this product with Omnitron within 90 days from the date of shipment. TO REGISTER, COMPLETE AND MAIL OR FAX THE REGISTRATION PORTION OF THIS INSTRUCTION MANUAL TO THE INDICATED ADDRESS. During the warranty period, Omnitron will, at its option, repair or replace a product which is proven to be defective.
For warranty service, the product must be sent to an Omnitron designated facility, at Buyer’s expense. Omnitron will pay the shipping charge to return the product to Buyer’s designated US address using Omnitron’s standard shipping method.
Warning
Caution
Warranty
Limitation of Warranty
The foregoing warranty shall not apply to defects resulting from improper or inadequate use and/or maintenance of the equipment by Buyer, Buyer­supplied equipment, Buyer-supplied interfacing, unauthorized modifications or tampering with equipment (including removal of equipment cover by personnel not specifically authorized and certified by Omnitron), or misuse, or operating outside the environmental specification of the product (including but not limited to voltage, ambient temperature, radiation, unusual dust, etc.), or improper site preparation or maintenance.
No other warranty is expressed or implied. Omnitron specifically disclaims the implied warranties of merchantability and fitness for any particular purpose.
Exclusive Remedies
The remedies provided herein are the Buyer’s sole and exclusive remedies. Omnitron shall not be liable for any direct, indirect, special, incidental, or consequential damages, whether based on contract, tort, or any legal theory.
Notes:
____________________________ ____________________________ ____________________________ ____________________________ ____________________________ ____________________________ ____________________________ ____________________________ ____________________________ _____________________________ ____________________________ ____________________________ ____________________________ ____________________________ ____________________________ ____________________________
Form:040-04210-001-B 10/03
Loading...