Omnitron Systems Technology FlexCeiver 10FL User Manual

FlexCeiverTM 10FL User Instructions
Description:
The FlexCeiver with IEEE 802.3 and Ethernet Versions 1.0 / 2.0. They enhance networking media connectivity using 10Base­FL with single-mode (SM) and multimode (MM) fiber, 10Base-2 thin coax and 10Base-T twisted pair (UTP).
All FlexCeivers have a 15-pin AUI connector that attaches to a mating AUI connector mounted on hosting Ethernet DTE equipment such as a workstation or a PC, or on a repeater such as a hub or a switch.
These FlexCeiver 10FL models are described here:
Model Fiber Type Max Distance
4200 850 nm (MM) 2 km 4201 1310 nm (SM) 30 km 4202 1310 nm (MM) 5 km
All 10FL models provide switch selectable Full-Duplex operation that allows data to flow between two Ethernet switches or a PC and a switch in both directions simultaneously, doubling the 10 Mbps Half-Duplex Ethernet to 20 Mbps.
TM
family of transceivers are compatible
Mounting:
Insert the Omnitron FlexCeiver 10FL into the 15-pin AUI port on a PC, workstation, hub or switch; slide the connector latch locking it into place. If an AUI cable is used, it is limited to 50 meters (164 ft.). Attach the fiber cables to the FlexCeiver 10FL ST connectors. Note that the FlexCeiver transmit (Tx) must attach to the receive side on the device at the far end of the fiber and the receive (Rx) must attach to the transmit side.
Switch Settings: “SQE” switch: When attaching to a PC (or a
workstation), the SQE switch should be set to “SQE Enable” (factory setting). When connecting to a hub or a switch, it should be set to “SQE Disable.”
“Duplex” switch: When attaching to a hub or a PC connected to a hub, the Duplex switch should be set to “Half-Duplex” (factory setting). When attaching to an Ethernet switch or a PC (or workstation) attached to an Ethernet switch, the FlexCeiver can be set to “Full­Duplex.” Note that in order to take advantage of the Full-Duplex performance improvement, the PC Network Interface Card (NIC) must also be set to “Full-Duplex.”
LED indicators: LED Color Description
Transmit Green Transmitted data activity Receive Green Received data activity Link Active Green Operational device at the far end Jabber Err Red Attached host unit violated
transmission time, could indicate a faulty Network Interface Card
(when attached to a PC). Power On Y ellow Power applied from attached unit Full-Duplex Yellow “Full-Duplex” indicator SQE Enable Y ellow “SQE Enable” indicator Collision Yellow Collision (normal operation)
Technical Support:
If you encounter problems in installing or maintaining this product, contact Omnitron Technical Support:
Phone: (949) 250-6510 Fax: (949) 250-6514 Email: support@omnitron-systems.com Address: Omnitron Systems Technology, Inc.
140 Technology Drive, #500 Irvine, CA 92618 USA
User Warranty Registration
Omnitron Systems Technology, Inc.
140 Technology Drive, #500
Irvine, CA 92618 USA
Fax: (949) 250-6514
Please register on-line @ http://www.omnitron-systems.com or complete both
sides and mail or fax this registration form to:
Name: _________________________________________________
______________________________________________
Company: ______________________________________________
Address: ______________________________________________
Please complete both sides of this form
City: ___________________ State: _______ Zip Code: ________
Country: _______________________________________________
Phone: ____________________ Fax: _______________________
E-mail:_________________________________________________
Warning
The operating description in this Instruction Manual is for use by qualified personnel only. To avoid electrical shock, do not perform any servicing of this unit other than that contained in the operating instructions, unless you are qualified and certified to do so by Omnitron Systems T echnology , Inc.
Caution
All user-required operations can be performed without opening the unit. Never attempt to open or remove the cover or tamper with the unit.
Warranty
This product is warranted to the original purchaser against defects in material and workmanship for a period of TWO YEARS from the date of shipment. A LIFETIME warranty may be obtained by the original purchaser by REGISTERING this product with Omnitron within 90 days from the date of shipment. TO REGISTER, COMPLETE AND MAIL OR FAX THE REGISTRA TION PORTION OF THIS INSTRUCTION MANUAL TO THE INDICATED ADDRESS. Or you may register your product on the internet at http://www.omnitron-systems.com. During the warranty period, Omnitron will, at its option, repair or replace a product which is proven to be defective.
For warranty service, the product must be sent to an Omnitron designated facility, at Buyer’s expense.
Omnitron will pay the shipping charge to return the product to Buyer’s designated US address using Omnitron’s standard shipping method.
Limitation of Warranty
The foregoing warranty shall not apply to defects resulting from improper or inadequate use and/or maintenance of the equipment by Buyer, Buyer-supplied equipment, Buyer-supplied interfacing, unauthorized modifications or tampering with equipment (including removal of equipment cover by personnel not specifically authorized and certified by Omnitron), or misuse, or operating outside the environmental specification of the product (including but not limited to voltage, ambient temperature, radiation, unusual dust, etc.), or improper site preparation or maintenance.
No other warranty is expressed or implied. Omnitron specifically disclaims the implied warranties of merchantability and fitness for any particular purpose.
Exclusive Remedies
The remedies provided herein are the Buyer’s sole and exclusive remedies. Omnitron shall not be liable for any direct, indirect, special, incidental, or consequential damages, whether based on contract, tort, or any legal theory.
Form:040-04200-001B 11/07
Notes:
____________________________ ____________________________ ____________________________ ____________________________ ____________________________ ____________________________ ____________________________ ____________________________ ____________________________ _____________________________ ____________________________ ____________________________ ____________________________ ____________________________ ____________________________ ____________________________
User Warranty Registration
Please register on-line @ http://www.omnitron-systems.com or complete both
sides and mail or fax this registration form to:
FlexCeiver Type: p 10FL p 10T p 10B2 p Other __________
Model: _________________________________________________
Serial Number: ______________ Purchase Date:______________
Purchased From: _________________________________________
Address: ______________________________________________
City: ___________________ State: _______ Zip Code: ________
Country: _______________________________________________
Please complete both sides of this form
______________________________________________________
______________________________________________________
Comments and Suggestions: _______________________________
Loading...