Omnitron Systems
T echnology, Inc.
.............................................................................................................
OmniRepeater™ 400FTD
AS/400 5250 and 5250 Express Fiber Converter
FEATURES
The OmniRepeater 400FTD is an AS/400 5250 and
5250 Express repeater/converter. I t converts between
UTP and fiber for backbone and fiber-to-the-desk
applications.
The FTD supports distances of 3,000 feet on UTP,
15,000 feet on multimode fiber and 30,000 feet on
single-mode fiber.
The FTD features a built-in fiber tester for easy
installation. It allows testing of total fiber connectivity
and eliminates the need for a costly fiber tester.
Pow e rful diagnostics monitor data activity and errors
resulting in easy installation.
Digital Phase Locked Architecture (PLA) facilitates
reliable data detection resulting in stable operation in
electrically noisy environments.
Data regeneration, reclocking and lost-bit recovery
features provide highly reliable operation.
Polarity detection and control facilitate usage with
different baluns.
Supports single-mode and multimode fiber.
Lifetime warranty.
DESCRIPTION
The OmniRepeater™ 400FTD is an AS/400 5250 and 5250
Express data repeater and fiber converter . It converts between UTP
and fiber and provides connectivity for one 5250 host port. It
supports multimode fiber for distances up to 15,000 feet and singlemode fiber for up to 30,000 feet. It supports unshielded twisted
pair (UTP) for distances up to 3,000 feet. It can be utilitized in
fiber backbones or in fiber-to-the-desk applications.
The FTD utilizes Omnitron ’ s Digital Phase Locked Architectur e
(PLA) for data detection, synchronization, retiming and repeating.
This technology enables the reliable detection and
synchronization of data with -2% to +4% data rate variation. It
also facilitates lost-bit recovery thus enhancing connectivity reliability .
Interface to the FTD is via UTP RJ11/RJ45 and fiber via ST
connectors. For UTP applications, at least category 3 wiring is
recommended. Lower grade wiring may be acceptable for shorter
distances. Both single-mode and multimode fiber models are
available.
The FTD includes a built-in fiber tester. This feature eliminates the
need for an expensive fiber tester and helps in installation and fault
isolation. It is compatible with all of Omnitron ’ s 5250 fiber products,
thus providing independent end-to-end cable testing.
The diagnostic features of the OmniRepeater 400 FTD assist in
both installation and monitoring of normal operation. Each data
frame is checked and true activity and data errors are reported. They
Omnitron Systems T echnology , Inc. • 140 Technology Dr., S uite 500 • Irvine, CA 92618 • 949.250.6510 tel. • 949.250.6514 fax • www .omnitron-systems.com
provide continuous line quality monitoring and early problem
detection.
The Express models operate with both 5250 and 5250 Express
protocols. Each port provides data rates of 1 Mbps for standard
5250 and 2 Mbps for 5250 Express protocol.
ORDERING INFORMATION
Standard 5250
5250 Express Description
2900-1 2940-1 Multimode fiber, 110 VAC
2900-2 2940-2 Multimode fiber, 110/230 VAC
Models Discontinued as of January 2009
2910-1 2950-1 Single-Mode fiber, 110 VAC
2910-2 2950-2 Single-Mode fiber, 110/230 VAC
SPECIFICATIONS
Protocol: IBM 5250 and 5250 Express for
Systems AS/400 and 3X
Devices Supported: All twinax IBM compatible devices
Interface:
Fiber: MM--50/125, 62.5/125, 100/140 µm
UTP: Categories 3, 4, 5 (EIA/TIA 568) or
higher
Data Rate:
Standard 5250: 1 Mbps -2%, +4%
5250 Express: 1 or 2 Mbps -2%, +4%
Supported Distances:
UTP: 3,000 ft.
Multimode Fiber: 15,000 ft.
Indicators:
Power: Green LED (1)
Test: Red LED (1)
Activity/Error Green/Red LED (2)
Dimensions: W:3.46”xD:2.83”xH:0.78”
Weight: 6 oz.
Power: 110 or 230 VAC, 80/40 mA
Temperature:
Operating: 0 to 45 degrees C
Storage: -40 to 75 degrees C
Humidity: Up to 90% (non-condensing)
AS/400
Balun
Balun
SAMPLE APPLICATION
B: Backbone Application
Fiber
OmniMux™ 400XL
Fiber Fiber
A: Fiber-To-The-Desk
OmniMux™ 400
Fiber
UTP
Trademarks are owned by their respective companies
OmniMux, OmniStar, OmniRepeater are trademarks of
Omnitron Systems Technology, Inc.
Specifications subject to change without notice.
©2009 Omnitron Systems Technology, Inc.
091-02900-002D 3/09
140 Technology Dr., Suite 500, Irvine, CA 92618
Tel: (949) 250-6510 Fax: (949) 250-6514
Email: info@omnitron-systems.com
http://www.omnitron-systems.com