Page 1
XS 250
PR-2226
This product manual contains important information about the safe installation and use of this
projector. Please read and follow these instructions carefully and keep this manual in a safe place
for future reference.
PR LIGHTING LTD.
http://www.pr-lighting.com
Page 2
INDEX
SAFE USAGE OF THE PROJECTOR 3
INSTALLING THE PROJECTOR 4
FITTING THE LAMP 4
POWER SUPPLY – MAINS 5
CONTROL CONNECTIONS 5
DMX TERMINATOR 6
SETUP OPTIONS-PROJECTOR CONFIGURATION 6
TO SET THE DMX START ADDRESS 6
MASTER/SLAVE MODE 7
STAND-ALONE MODE 7
OPERATION MENU 8
ERROR MESSAGES 11
REPLACING GOBOS 11
DMX PROTOCOL 12
LED INDICATION 14
MAINTENANCE 14
LUBRICATION 14
KEEPING THE PROJECTOR CLEAN 14
TROUBLESHOOTING 15
TECHNICAL DATA 16
ELECTRICAL DIAGRAM 19
COMPONENT ORDER CODES 20
Please note that as part of our ongoing commitment to continuous product development, specifications are subject to change without
notice. Whilst every care is taken in the preparation of this manual we reserve the right to change specifications in the course of
product improvement. The publishers cannot be held responsible for the accuracy of the information herein, or any consequence
arising from them.
Every unit is tested completely and packed properly by the manufacturer. Please make sure the packing and / or the unit are in good
condition before installation and use. Should there be any damage caused by transportation, consult your dealer and do not use the
unit. Any damage caused by improper use will not be assumed by the manufacturer and / or dealer.
ACCESSORIES
These items are packed together with the projector:
Name Quantity Unit Remark
Clamps 2 Pcs
Screws for clamp 4 Pcs
5-pin connetor 1 Pc Without cable
Safety cord 1 Pc
Spare gobos 4 Pcs
This manual 1 Pc
2/22
Page 3
SAFE USAGE OF THE PROJECTOR
When unpacking and before disposing of the carton check there is no transportation damage before using the projector.
Should there be any damage caused by transportation, consult your dealer and do not use the apparatus.
The projector is for indoor use only, IP20. Use only in dry locations. Keep this device away from rain and moisture,
excessive heat, humidity and dust. Do not allow contact with water or any other liquids.
The projector is not designed or intended to be mounted directly on to inflammable surfaces.
The projector is only intended for installation, operation and maintenance by qualified personnel.
The projector must be installed in a location with adequate ventilation, at least 50cm from adjacent wall surfaces. Be sure
that no ventilation slots are blocked.
Do not project the beam onto inflammable surfaces, minimum distance is 5m. 5m
Avoid direct exposure to the light from the lamp. The light is harmful to the eye.
Do not attempt to dismantle and/or modify the projector in any way.
Electrical connection must only be carried out by qualified personnel.
Before installation, ensure that the voltage and frequency of power supply match the power requirements of the projector.
It is essential that each projector is correctly earthed and that electrical installation conforms to all relevant standards.
Do not connect this device to any other types of dimmer apparatus.
Make sure that the power-cord is never crimped or damaged by sharp edges. Never let the power-cord come into contact
with other cables. Only handle the power-cord by the plug. Never pull out the plug by tugging the power-cord.
Keep the lamp clean. Do not touch the lamp glass with bare hand.
The projector should always be installed with a secondary safety fixing. A safety cord is supplied for this; it should be
attached as shown in “installing the projector” section.
The lamp used in this projector is a discharge lamp. After switching off don’t attempt to restart the projector until lamp has
cooled, this will require approx 15 minutes. Switching the lamp on and off at short intervals will reduce the life of both the
lamp and the projector. But occasional breaks will prolong the life of the lamp and projector.
Never run the projector without a lamp.
The lamp shall be changed if it has become damaged or thermally deformed.
Shields and lens shall be changed if they have become visibly damaged to such an extent than their effectiveness is
impaired, for example by cracks or deep scratches.
Exterior surface temperatures of the luminaire after 5 minutes operation is 80℃, when steady state is achieved 120℃,
There is no user serviceable parts inside the projector, do not open the housing and never operate the projector with the
covers removed.
Always disconnect from the mains, w hen the device is not in use or before cleaning it or
before attempting any maintenance work !
If you have any questions, don’t hesitate to consult your dealer or manufacturer.
3/22
Page 4
INSTALL THE PROJECTOR
Take 2 clamps and the safety cord out from the package and mount 2 clamps on the underside of fixture with 2 retainers
attached to each clamp. Hang the fixture on the structure and fasten the screws attached to each clamp. (See the
WARNING
Always ensure that the projector is firmly anchored to avoid vibration and slipping whilst functioning. Always ensure that
the structure that you are going to mount the projector is secure and is strong enough to support a weight of XS 250.
WARNING:
1. Unlock the P AN and TILT before the 1
2. The projector MUST be lifted or carried by the HANDLES instead of clamps.
3. For safety the safety cord should afford 10 times of the unit’s weight.
on the underside of the base as shown above) To pass SAFETY CORD through 2 HOLES for safety!
st
application of projector for safety .
FITTING THE LAMP
Lock the yoke before fitting/replacing the lamp.
Open the cover board at the rear of the projector by loosening 3 screws, you can see the structure as shown in the figure
above.
Gently pull out lamp holder assembly.
Take out the worn-out lamp. Insert the new lamp to the socket. Note: don’t touch the bulb of the new lamp with bare
hand so as not to influence the beam output.
Close the rear cover and fasten 3 screws.
WARNING: The MSD series are high-pressure lamps w ith external igniters (
when handling these lamps. Always read the manufacturers "Instructions for use" enclosed with the lamp.
4/22
). Care should alwa ys be taken
Page 5
POWER SUPPLY-MAINS
Connect the power cord as follows:
L (live) =brown
E (earth) =yellow/green
N (neutral) =blue
Use the plug provided to connect the mains power to the projector paying attention to the voltage and frequency marked
on the panel of the projector. It is recommended that each projector be supplied separately so that they may be
individually switched on and off.
IMPORT ANT
It is essential that each projector is correctly earthed and the electrical installation conforms to a ll relevant
standards.
CONTROL CONNECTION
Connection between controller and projector and between one projector and another must be made with a 2
core-screened cable, with each core having at least a 0.5mm diameter. Connection to and from the projector is via
cannon 3 pin (which are included with the projector) or 5 pin XLR plugs and sockets. The XLR's are connected as shown
in the figure above.
Note: care should be taken to ensure that none of the pins touch the metallic body of the plug or each other. The body of
the plug is not connected in any way. The XS 250 accepts digital control signals in protocol DMX512 (1990).
Connect the controller’s output to the first fixture’s input, and connect the first fixture’s output to the second fixture’s input
and connect the rest fixtures in the same way. Eventually connect the last fixture’s output to a DMX terminator as shown
in the figure below.
5/22
Page 6
DMX TERMINATOR
In the Controller mode, at the last fixture in the chain, the DMX output has to be connected with a DMX terminator. This
prevents electrical noise from disturbing and corrupting the DMX control signals.
The DMX terminator is simply an XLR connector with a 120Ω (ohm) resistor connected across pins 2 and 3, which is
then plugged into the output socket on the last projector in the chain. The connections are illustrated below.
2
120
1
3
DMX TERMINATOR
CONNECTION
Connect a 120 (OHM) resistor
across pins 2 and 3 in an XLR plug
and insert into the DMX out socket
on the last unit in the chain.
PIN 2
PIN 3
SETUP OPTIONS-PROJECTOR CONFIGURATION
Projector configuration can be set conveniently via pressbutton switch and LED display. Turn the projector on and the
LED display will show DMX address you set and save last time and it can be reset and saved again as you please.
Launch the projector. Press button ENTER more than 5 seconds to unlock panel.
Press button UP or DOWN if you want to browse through the various Setup Options. There are 10 option codes
from AddR to Edit, and each code has a specific function.
Press button ENTER to save your settings or enter the next menu.
Press button UP or DOWN to shift.
Press button FUNC, it will return to the upper menu one by one. If you stay for minutes defaulted will show display status
automatically.
TO SET THE DMX START ADDRESS
Each XS 250 must be given a DMX start address so that the correct projector responds to the correct control signals.
This DMX start address is the channel number from which the projector starts to “listen” to the digital control information
being sent out from the controller. The XS 250 has 3 DMX modes. There are standard mode, extended mode and short
mode. For example standard mode has 16 channels, so set the No. 1 projector’s address 001, No. 2 projector’s address
017, No. 3 projector’s address 033, No. 4 projector’s address 049, and so on.
Launch the projector. Press button ENTER or coder knob more than 5 seconds to unlock panel.
Press button FUNC to display AddR.
Press button UP and DOWN , you can set the address;
Press button ENTER to confirm; In the same time. The GREEN LED will flash one time. It means the setting has
6/22
Page 7
been enabled.
Press button FUNC, it will return to the upper menu one by one.
STAND-ALONE MODE
Operate the projector without connecting a controller, enable the master mode in the operation panel, the
projector will run in Stand-Alone mode automatically.
MASTER/SLAVE MODE
Without using a controller, many projectors can run synchronously in the Master/Slave mode by linking them
with each other. Select one projector as the master with setting options master mode enabled but slaves.
Regard the other projectors as the slaves with setting options slave mode enabled and all DMX start
address “001”.
Connect the controller’s output to the first fixture’s input, and connect the first fixture’s output to the second fixture’s input
and connect the rest fixtures in the same way. Eventually connect the last fixture’s output to a DMX terminator as shown
in the figure below.
7/22
Page 8
OPERATION MENU
1st LEVEL 2nd LEVEL 3rd LEVEL 4th LEVEL 5th LEVEL 6th LEVEL
DMX Address
001－501 in Short Mode
AddR
RST RST?
CNFG
OPTN
dISP
INFO
TEST
001－497 in Standard
Mode
001－495 in Extended
Mode
dMX
（Defaults：STd）
LdMX
（Defaults：NORM）
LAMP
（Defaults：CTRL）
COLR
（Defaults：STEP）
GObO
（Defaults：STEP）
P\IN
（Defaults：OFF）
T\IN
（Defaults：OFF）
PT\S
（Defaults：OFF）
d\IN
（Defaults：OFF）
dFLT
（Defaults：OFF）
d\MD
（Defaults：ON）
d\IN
（Defaults：OFF）
L\HR XX RST?
T\HR XX
TEMP
VER MSTR X.X.X
dMXd XX
SNUM
（Reserved）
SET
（Defaults：OFF）
SELF OFF
STd
EXT
SHRT
NORM
HOLd
CTRL
ON
dMX
STEP
LIN
STEP
LIN
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
ON
OFF
dIM
OFF
ON
MSTR XX℃
HEAd XX ℃
OFF
ON
8/22
Page 9
s
LAMP
X
C
C
C
C
X
MOdE
（Defaults :dMX）
EdIT MEM
（Default
：OFF）
STRT
ON
OFF
dMX
MSTR
SLAV
STAT
ON
Statu s = XX
Control = X
UM 1
UM 2
PM 1
PM 2
PM 3
UM 1
UM 2
PM 1
PM 2
PM 3
UM 1
UM 2
TIME
MIC
TIME
MIC
TIME
MIC
TIME
MIC
TIME
MIC
TIME
MI
TIME
MI
TIME
MIC
TIME
MI
TIME
MI
SN XX
（1~28）
SN XX
（1~28）
SHUT XXX（0~255）
dIM XXX（0~255）
COLR XXX（0~255）
GObO XXX（0~255）
RGbO XXX（0~255）
GROT XXX（0~255）
PRSM XXX（0~255）
PROT XXX（0~255）
FOCS XXX（0~255）
PAN H X X X（0~255）
PAN L X X X（0~255）
TLTH XXX（0~255）
TLTL XXX（0~255）
MSPd XXX（000~255）
dELY
LINK XX（1~28）
SHUT XXX（0~255）
dIM XXX（0~255）
COLR XXX（0~255）
GObO XXX（0~255）
RGbO XXX（0~255）
GROT XXX（0~255）
PRSM XXX（0~255）
PROT XXX（0~255）
FOCS XXX（0~255）
XX
（0.25s~100min）
9/22
Page 10
INIT
2
S
STAT
I M1
I M2
I SS
PAN H X X X（0~255）
PAN L X X X（0~255）
TLTH XXX（0~255）
TLTL XXX（0~255）
MSPd XXX（000~255）
dELY （0.25s~100min）
LINK XX（1~28）
SHUT XXX（0~255）
dIM XXX（0~255）
COLR XXX（0~255）
GObO XXX（0~255）
RGbO XXX（0~255）
GROT XXX（0~255）
PRSM XXX（0~255）
PROT XXX（0~255）
FOCS XXX（0~255）
PAN H X X X（0~255）
PAN L X X X（0~255）
TLTH XXX（0~255）
TLTL XXX（0~255）
MSPd XXX（000~255）
RM1？
(Unlock
UP/DOWN/ENTER)
？
RM
（Unlock
UP/DOWN/ENTER）
RS
？
（Unlock
UP/DOWN/ENTER）
OK
OK
OK
10/22
Page 11
ERROR MESSAGES
In the course of launch, XS 250 examines automatically whether there are errors and if there are, it will display
information as follows:
Display
Message
SE 1 Zoom (1# motor) error
SE 6 Rotating Gobo wheel (6# motor) error
SE7 Gobo rotation 1 (7# motor 1) error
SE 9 Fixed Gobo wheel (9# motor) error
SE10 Colour wheel (10# motor) error
REPLACING GOBOS
Disconnect the fixture from power. Lock Tilt. Carefully lift off the cover by undoing the 6 screws.
For gobos replacement on the fixed gobo: Remove the gobo and insert the new one into the position b y hands.
For gobos replacement on the rotating gobo wheel: Remove th e gobo holder with gobo from gobo wheel by
hands.
Pull out the spring and drop the old gobo out of the holder.
Insert the new gobo into the holder, and then insert the spring with the narrow end against the gobo.
Push the end of the spring in under lip of the holder.
Pick the spring clip up and put the gobo holder back into the position, if necessary, a small screwdriver will be
helped.
Note: If the gobo is a glass one, it should be touched with glabrous, clean and soft tissue or cloth matted between hand
and glass instead of with bare hand.
Close the rear cover and fasten 6 screws.
11/22
Page 12
t
t
DMX PROTOCOL
Short
mode
1 1 1 Strobe
2 2 2 Dimmer 000-255 Dimming from dark to light (0-100%)
3 3 4 Colour Wheel
4 4 5
Standard
mode
3 Dimmer Fine 000-255 Dimmer in 16 Bit precision
Extended
mode
FUNCTION DMX DESCRIPTION
000-009 Black
011-025 Open
026-225 Strobe speed from slow to fast
226-255 Open
White
Colour 1
Colour 2
Colour 3
Colour 4
Colour 5
Colour 6
Colour 7
Colour 8
Colour 9
Colour 10
Colour 11
Colour 12
white
Rainbow rotation speed from slow to fast
Stop in current position
Rainbow reverse rotation speed from
slow to fas
Clear
Gobo1
Gobo 2
Gobo 3
Gobo 4
Gobo 5
Gobo 6
Gobo 7
Gobo
Gobo
Gobo
Rainbow rotation speed from slow to fast
Rainbow reverse rotation speed from
slow to fas
Gobo shake 1 (From slow to fast)
Gobo shake 2 (From slow to fast)
Gobo shake 3 (From slow to fast)
Gobo shake 4 (From slow to fast)
Gobo shake 5 (From slow to fast)
Fixed Gobo
Wheel
000-020
021-028
029-037
038-045
046-054
055-062
063-071
072-080
081-088
089-097
098-105
106-114
115-123
124-127
128-187
188-195
196-255
000-011
012-023
024-034
035-046
047-057
058-069
070-080
081-092
093-103
104-115
116-127
128-150
151-171
172-183
184-191
192-199
200-207
208-215
12/22
Page 13
216-223
t
t
5
9
7Ro
t
6
t
9
5
5
5
5
5
t
5
5
8
t
8
3
5
224-231
232-239
240-247
248-255
000-016
017-032
033-048
049-064
065-080
081-096
097-112
113-127
5 5 6
Rotating Gobo
Wheel
128-150
151-171
172-183
184-195
196-207
208-219
220-231
232-243
244-255
000-127
128-188
6 6 7 Gobo rotation
189-194
195-255
7 8
7 8 9 Prism / Frost
8 9 10 Prism rotation
10 11 Focus 000-25
12 Focus Fine 000-25
10 11 13 Pan 000-25
12 14 Pan Fine 000-25
11 13 1
14 16 Tilt Fine 000-25
15 17
12 16 18 Control
Remark:
If you intend to turn on/off the lamp via the last channel of the controller, don’t attempt to push the channel to value
224-255 immediately after turning it off, or push the slide bar to value 224-255 to wait it cooling. Under these 2
circumstances, the lamp can not be turned on. The right operation is: turn it off---cool down---push the slide bar to turn it
on.
Til
Gobo rotation
Fine
Pan & Tilt
speed
13/22
000-255 Gobo rotation in 16 Bit precision
000-020 Clear
021-25
000-00
010-12
128-13
137-255
000-25
000-255 Pan&Tilt speed from fast to slow
000-04
049-080 Rese
081-112 Reserved
113-144 Lamp off ( stop in DMX value for 10 s)
145-16
169-200 Lamp power reduced to 50%
201-22
224-25
Gobo shake 6 (From slow to fast)
Gobo shake 7 (From slow to fast)
Gobo shake 8 (From slow to fast)
Gobo shake 9 (From slow to fast)
Gobo shake 10 (From slow to fast)
white
Gobo1
Gobo 2
Gobo 3
Gobo 4
Gobo 5
Gobo 6
Gobo7
Rotation speed from slow to fast
Reverse rotation speed from slow to
fas
Gobo shake 1 speed from slow to fast
Gobo shake 2 speed from slow to fast
Gobo shake 3 speed from slow to fast
Gobo shake 4 speed from slow to fast
Gobo shake 5 speed from slow to fast
Gobo shake 6 speed from slow to fast
Gobo shake 7 speed from slow to fast
0~540°index
Rotation speed from slow to fast
Stop rotating
Reverse rotation speed from slow to
fas
Prism
Stop in current position
tation speed from slow to fas
Stop in current position
Reverse rotation speed from slow to
fas
Linearly focusing
Focus in 16 precision
Pan rotation 540°
Pan rotation in 16 precision
Tilt rotation 270°
Tilt rotation in 16 precision
Reserved
Reserved
Reserved
Lamp on (See remark below)
Page 14
LED INDICATION
On
Green
Yellow On
Blue On Power
Red/Green
Off
Flash
Red
Green
DMX signal OK
No DMX signal
DMX signal error
Setting the panel
Running slave mode or self test mode
Running master mode
MAINTENANCE
If the projector’s lens becomes damaged or broken it should be replaced. If the lamp becomes damaged or deformed in
any way it must be replaced. If the light from the lamp appears dim this would normally indicate that it is reaching the end
of its life and it should be changed at once, aged lamps run to the extremity of their life might explode. If the projector
does not function, check the fuses on the power socket of the projector, they should only be replaced by fuses of the
same specification. Should these be damaged call a qualified technician before replacement. The projector has thermal
protection device that will switch off the projector in case of overheating, should either of these operate, check that the
fans are not blocked, and if they are dirty clean them before switching on the projector again. Check that the fans are
operational, if not call a qualified technician.
Any maintenance work s hould only be carried out by qualified tec hnicians.
LUBRICATION
To ensure the continuous rotation of the rotating gobos and linear motion of the lens for focusing, it is recommended that
the bearings for the rotating gobos and the 2 shafts for the focusing lens holder be lubricated periodically, preferably
every two months. Use only high quality, high-temperature resistant grease instead of any type of oil. When lubricating
the bearings, a syringe with a fine needle is the easiest way to introduce the grease to the bearings around each gobo.
KEEPING THE PROJECTOR CLEAN
To ensure the reliability of the projector it should be kept clean. It is recommended that the fans should be cleaned every
15 days. The lens and dichroic colour filters should also be regularly cleaned to maintain an optimum light output.
NOT use any type of solvent on dichroic colour filters.
Cleaning frequency depends on the environment in which the fixture operates: damp, smoke or particularly dirty
surroundings can cause greater accumulation of dirt on the unit’s optics. A soft cloth and typical glass cleaning products
should be used in cleaning. It is recommended to clean the external optics at least once every 20 days and clean the
internal optics at least once every 30 / 60 days.
Do not use any organic solvent, e.g. alcohol, to clean the ref lector mirror, dichroic colour filters or housing of
the apparatus.
Do
14/22
Page 15
TROUBLESHOOTING
PROBLEM ACTION
The projector doesn’t switch on
The lamp comes on but the projector
doesn’t respond to the controller
The projector only functions intermittently ¾ Make sure the fan is working and not dirty.
Defective projection
The project image appears to have a halo
The beam appears dim
¾ Check the fuse on the power socket.
¾ Replace the lamp.
¾ Make sure that the projector is correctly configurated.
¾ Replace or repair the DMX cable.
¾ Check the lenses are not broken.
¾ Remove dust or grease from the lenses.
¾ Make sure the lamp is installed correctly.
¾ Carefully clean the optical group lenses and the projector
components.
¾ Check the optics is clean.
¾ Replace with a new lamp of the specified type and rating.
15/22
Page 16
TECHNICAL DATA
VOLTAGES:
220V, 50Hz
Options:
POWER CONSUMPTION:
370W
LAMP:
PHILIPS MSD 250W/2
Colour Temperature 8500°K
Socket GY9.5, single ended
Manufacturers Rated Lamp Life 2000 Hours replacement
Or
OSRAM HSD 250/78
Colour Temperature 7800°K
Socket GY9.5, single ended
Manufacturers Rated Lamp Life 3000 Hours replacement
Or
GE CSD250/2/SE
Colour Temperature 8500°K
Socket GY9.5, single ended
Manufacturers Rated Lamp Life 3000 Hours replacement
COLOURS:
1 wheel with 12 dichroic colour filters plus white
With variable speed bi-directional rainbow effect
Step/linear colour changing is available
GOBOS:
1 Rotating gobo wheels:
7 interchangeable gobos+ white, glass or metal gobos can be fixed
Indexable, bi-directionally rotatable at variable speeds
1 Fixed gobo wheel :
10 interchangeable gobos+ white
bi-directional wheel scrolling at variable speeds
Gobo diameter: Φ22.5mm
Gobo image diameter: Φ17mm
PRISM
1x3 facet prism, bi-directionally rotatable at variable speeds
100V/120V/200V/220V/230V/240V AC，50/60Hz
16/22
Page 17
FOCUS:
DMX controlled focus
DIMMER:
0-100% linearly adjustable
SHUTTER:
Double shutter blades, 0.3~12 F.P.S
HEAD MOVEMENT :
Pan 540º, Tilt 270º with auto position correction
BEAM ANGLE:
16°
CONTROL:
DMX512, 3 pin, 5 pin interfaces
RDM control protocol
12 channels in short mode, 16 channels in standard mode, and 218channels in extended mode.
Master/Slave mode
Stand-alone mode
Self-test mode
OTHER FUNCTIONS:
Adjustable Pan & Tilt speed
Fixture and lamp usage time display
LED display with English language menu
Energy saving function of the ballast
Built-in analyzer for easy fault finding, error messages
Built-in demo sequences
Input signal isolating protection
HOUSING:
Composite plastic, IP20
WEIGHT:
22Kg
SIZES:
See at below
17/22
Page 18
LIGHT OUTPUT :
18/22
Page 19
M4-1
STROBE
M4-2
STROBE
M2
PRISM
M11
+
+
SENS
-
-
M21
S1 S2 S3 S4 S5
VSGVSG VSG VSG VSG
M12
M22
M9
FIXED GOBOS
M13
M23
mark side
M10
COLOUR
M14
M24
mark side
M15
M25
M8
FOCUS
M11
+
+
SENS
-
-
M21 M22
S1 S2 S3 S4 S5
VSG
mark side
VSG VSG
M7
GOBO ROTATINGM6ROTATING-GOBOM3PRISM ROTATING
M13
mark side
M23
M14
M24
VSG
mark side
M15
M25
VSG
M11 M12
PAN TILT
AC Plug
E
N
L
POWER-SW
Filter
Delay Fuse
M1 M2 M3 M4 M5 M6 M7 M8 M9 M10 M11 M12
-
s
+
S11S12
-
s
+
PRISM PRISM ROTATING STROBE ROTATING-GOB OGOBO ROTATINGFOCUS FIXED GOBOS COLOUR
+
-
CN9
A1 A2
CN6
-
CN3
DMX
CN7CN8
-
S1 S6
-
-
678910
-
12345
PAN
-
+
+
+
+
TILT
+
-
+
PAN TILT
240V
230V
230V
220V
24VAC
Transformer
Ph
Ballast
Thermostat
Ph
Ballast
Ignitor
DL
AC20V
CH
BH
BL
BC
IG
AC
200V
120V
100V
0V
50Hz
60Hz
CAP1
50Hz
60Hz
LAMP
N
CAP2
DISPLAY PCB
SW1 SW2 SW3 SW4
VSG
1
51
12
3
DMX-IN DMX-OUT
234
12
3
DMX-IN DMX-OUT
BOX FAN
+
5
234
-
HEAD FAN
+
-
+
-
+
TILT-EncoderPAN-Encoder
-
Page 20
COMPONENT ORDER CODES
NAME PART NO. QUANTITY REMARK
TRANSFORMER 040030039 1 21V 100W/230V 320W
THERMOSTAT 190010065 1 75℃
BALLAST
IGNITOR 040090016 1 230V 50/60Hz
LAMP 100050057 1 MSD250/2
TILT DRIVE BELT
P AN DRIVE BEL T 290151251 1 HTD-447-3M
FAN I N BASE 030060057 1 DC24V/2.88W
FAN NEAR THE LAMP
PAN MOTOR 030040053 1 57BYGH301-3A
TIL T MOT OR 030040052 1 57BYGH101-2A
PRISM ROT A TION MOT OR
SHUTTER BLADE 1 MOTOR 1
SHUTTER BLADE 2 MOTOR
ROT A TING GOBO WHEEL MOT OR
PRISM/FROST MOTOR
ROT A TING GOBO WHEEL 2 MOT OR
FOCUS MOTOR
FIXED GOBO WHEEL MOT OR
COLOUR WHEEL MOTOR 1
MOTOR DRIVE PCB 230020252A 1
DISPLAY PCB 230020249 1
040070022 2 230V 50/60Hz
290151252 1 HTD-612-3M
030060053 1 24V 1.4W
1
030040095
17HD0013-36L
1
030040132
1
1
14HD0013-31L
030040148 1 17HD0013-62
1
0300401 12
1
17HD0013-38L 5*15
20/22
Page 21
21/22
Page 22
PR LIGHTING LTD.
1582 Xingye Avenue, Nancun Panyu
Guangzhou, 511442 China
TEL: +86-20-3995 2888
FAX: +86-20-3995 2330
P/N: 320020009B
Version: 20101129
22/22
Loading...