Page 1
SOLO 1200
PR-2902
This product manual contains important information about the safe installation and
use of this projector. Please read and follow these instructions carefully and keep this
manual in a safe place for future reference.
PR LIGHTING LTD.
No. 571, Yingbin Road, Dashi, Panyu, Guangzhou, 511430 China
http://www.pr-lighting.com
Page 2
SAFE USAGE OF THE PROJECTOR 3
INSTALLING THE PROJECTOR 4
FITTING THE LAMP 4
POWER SUPPLY – MAINS 5
CONTROL CONNECTIONS 5
DMX TERMINATOR 6
SETUP OPTIONS-PROJECTOR CONFIGURATION 6
TO SET THE DMX START ADDRESS 6
FUNCTIONS DISPLAY 7
REPLACING GOBOS 9
CHANGING BELTS 9
DMX CONTROL CHANNEL FUNCTIONS 10
LED INDICATION 13
MAINTENANCE 14
LUBRICATION 14
KEEPING THE PROJECTOR CLEAN 14
TROUBLESHOOTING 14
TECHNICAL DATA 15
ELECTRICAL DIAGRAM 16
COMPONENT ORDER CODES 17
Please note that as part of our ongoing commitment to continuous product development, specifications are
subject to change without notice. Whilst every care is taken in the preparation of this manual we reserve the
right to change specifications in the course of product improvement. The publishers cannot be held responsible
for the accuracy of the inf ormation herei n, or any conseque nce arising from t hem.
Every unit is tested completely and packed properly by the manufacturer. Please make sure the packing and / or
the unit are in good co ndition before ins tallation and use. Should there be any da mage caused by tran sportation,
consult your dealer and do n ot use the unit. Any damage caused by improper use will not b e assumed by the
manufacturer and / or dealer .
INDEX
ACCESSORIES
THESE ITEMS ARE PACKED TOGETHER WITH THE PROJECTOR
G clamps (2 PCS)
XLR cable with 3-pin plug and socket (1 PCS)
Safety cords (2 PCS)
Spare gobos (3 PCS)
This manual (1 PCS)
Ω clamps (Options) (2PCS)
Thank you for purchasing our product SOLO 1200, PR-2902.
This product manual contains important information about the safe installation and use of this projector.
Please read and follow these instructions carefully and keep this manual in a safe place for future
reference.
SOLO 1200 is an innovative projector with an elegant housing, which is of Pan’s and Tilt’s locks for
maintenance and high quality fans free from noise. The projector has 2 types of clamps for mounting
at any direction and position. Which complies to CE norms and standards and uses international
protocol DMX 512.
The projector uses Philips MSR1200 SA/DE discharge lamp and high quality optical system, which
produces bright and beautiful light beam and. The projector features effects of strobe, frost light, mixed
colours and prism, so it is suitable for applications in TV station, discotheque, singing and dancing
stage, nightclub, etc.
INTRODUCTION
2/18
SOLO 1200 EN.doc
Page 3
When unpacking and before disposing of the carton check there is no transportation damage before
using the projector. Should there be any damage caused by transportation, consult your dealer and do
not use the apparatus.
The projecto r is for indoor use only, IP20. Use only in dry l ocations. K eep this devic e away from rain
and moisture, excessive heat, humidity and dust. Do not allow contact with water or any other liquids.
SAFE USAGE OF THE PROJECTOR
The projector is not designed or intended to be mounted directly on to inflammable surfaces.
The projector is only intended for installation, operation and maintenance by qualified personnel.
The projector must be installed in a location with adequate ventilation, at least 50cm from adjacent
wall surfaces. Be sure that no ventilation slots are blocked.
Do not project the beam onto inflammab le surfaces, minimum dis tance is 5m.
Avoid direct exposure to the light from the lamp. The light is harmful to the eye.
Do not attempt to dismantle and/or modify the projector in any way.
Electrical connection must only be carried out by qualified personnel.
Before installation, ensure that the voltage and frequency of power supply match the power
requirements of the projector.
It is essential that each projector is correctly earthed and that electrical installation conforms to all
relevant standards.
Do not connect this device to any other types of dimmer apparatus.
Make sure that the power-cord is never crimped or damaged by sharp edges. Never let the power-
cord come into contact with other cables. Only handle the power-cord by the plug. Never pull out the
plug by tugging the power-cord.
Keep the lamp clean. Do no t touch the lamp glass with bare hand.
The projector should always be installed with a secondary safety fixing. A safety cord is supplied for
this; it should be attached as shown in “installing the projector” section.
The lamp used in this projector is a Philips MSR1200 SA/DE discharge lamp. After switching off don’t
attempt to restart the projector until lamp has cooled, this will require approx 15 minutes. Switching the
lamp on and off at short intervals will reduce the life of both the lamp and the projector. But occasional
breaks will prolong the life of the lamp and projector.
Never run the projector without a lamp.
There is no user serviceable parts inside the projector do not open the housing and never operate the
projector with the covers removed.
Always disconnect from the main s, wh en the device is not in use or before cl eaning it or before
attempting any maintenance work.
If you have any questions, don’t hesitate to co nsult your dealer or manufacturer.
5m
3/18
SOLO 1200 EN.doc
Page 4
INSTALLING THE PROJECTOR
SAFETY CORD
(2PCS)
SAFETY
CORD
HOLE
256
CLAMPS
(2PCS)
RETAINERS
(2PCS PER CLAMP)
HANDLES
(2PCS)
To pass 2 SAFETY CORDS
through 4 HOLES for safety!
4 HOLES FOR
SAFETY CORD
PASSING THROUGH
WARNING
To pass 2 SAFETY CORDS
through 4 HOLES for safety!
SAFETY
CORD
WARNING
HOLE
106
Take 2 clamps and 2 safety cords out from the package and mount 2 clamps on the underside of
fixture with 2 retainers attached to each clamp. Hang the fixture on the structure and fasten the screws
attached to eac h clamp. (Watch the WARNING
on the underside of the base as shown above) To
pass 2 SAFETY CORDS through 4 HOLES for safety! Always ensure that the projector is firmly
anchored to av oid vibratio n and slipping whilst function ing. Always ensure that th e structure th at you
are going to mount the projector is secure and is strong enough to support a weight of SOLO 1200.
WARNING: 1. Unlock the PAN and TILT before the 1
st
application of projector for safety.
2. The projector MUST be lifted or carried by the HANDLES instead of clamps.
FITTING THE LAMP
BULB
PST
TILT LOCK
2 SPRING PLATES
2 NUTS
Lock tilt before fitting/replacing the lamp.
Loosen 2 M5 screws of the back cover and open it, (You can see as shown in the right figure)
Loosen 2 lamp holder screws and take out the worn-out lamp.
Fit a new lamp then fasten 2 lampholder screws.
Notes: don’t touch the bulb of the new lamp with bare hand so as not to influence the beam
output.
WARNING: The MSR series are high-pressure lamps with external igniters (
). Care should
always be taken when handling these lamps. Always read the manufacturers "Instructions for
use" enclosed with the lamp.
4/18
SOLO 1200 EN.doc
Page 5
POWER SUPPLY - MAINS
Connect the power cord as follows:
L (live) =brown
E (earth) =yellow/green
N (neutral) =blue
Use the plug provided to connect the mains power to the projector paying attention to the voltage and
frequency marked on the panel of the projector. It is recommended that each projector be supplied
separately so that they may be individually switched on and off.
IMPORTANT
It is essential that each projector is correctly earthed and the electrical installation conforms to
all relevant standards. Power consumption of the SOLO 1200 is 1350W.
CONTROL CONNECTIONS
Connection between controller and projector and between one projector and another must be made
with 2 core-screened cables, with each core having at least a 0.5mm diameter. Connection to and
from the projector is via cannon 3 pin (which are included with the projector) or 5 pin XLR plugs and
sockets. The XLR's are connected as shown in the figure above.
Note: care should be taken to ensure that none of the pins touch the metallic body of the plug or each
other. The body of the plug is not connected in any way. The SOLO 1200 accepts digital control
signals in protocol DMX512 (1990).
Connect the controller’s output to the first fixture’s input, and connect the first fixture’s output to the
second fixture’s input and connect the rest fixtures in the same way. Eventually connect the last
fixture’s output to a DMX terminator as shown in the figure below.
DMX OUTDMX IN DMX IN DMX OUT DMX IN DMX OUT
DMX IN FROM
CONTROLLER
TERMINATOR
5/18
SOLO 1200 EN.doc
Page 6
DMX TERMINATOR
In the Controller mode, at the last fixture in the chain, the DMX output has to be connected with a DMX
terminator. This prevents electrical noise from disturbing and corrupting the DMX control signals.
The DMX terminator is simply an XLR connector with a 120Ω (ohm) resistor connected across pins 2
and 3, which is then plugged into the output socket on the last projector in the chain. The connections
are illustrated below.
2
1
120
3
DMX TERMINATOR
CONNECTION
Connect a 120 (OHM) resistor
across pins 2 and 3 in an XLR plug
and insert into the DMX out socket
on the last unit in the chain.
PIN 3
PIN 2
SETUP OPTIONS - PROJECTOR CONFIGURATION
UP
Projector configuration can be set conveniently via pressbutton switch and digital display.
Turn the projector on and the digital display will show DMX address you set and save last time and it
can be reset and saved again as you please.
Press butt on UP or DOWN if you want to browse through the various Setu p Options.
Press button ENTER to save your settings or enter the next menu.
Press button UP or DOWN to shift the display or change the display of address.
Press button FUNC , it will return to the upper menu one by one. The display will return automatically
to the function of address display if you stay for about 60 seconds defaulted.
TO SET THE DMX START ADDRESS
Each SOLO 1200 must be given a DMX start address so that the correct projector responds to the
correct control signals. This DMX start address is the channel number from which the projector starts
to “listen” to the digital control information being sent out from the controller. The SOLO 1200 has 18
channels, so set the No. 1 projector’s address 001, No. 2 projector’s address 019, No. 3 projector’s
address 037, No. 4 projector’s address 055, and so on.
Launch the projector. Press button ENTER more than 5 seconds to unlock panel.
Press button FUNC to ;
Press button ENTER, it will display address;
Press button UP and DOWN, you can set the address;
Press button ENTER to confirm.
6/18
SOLO 1200 EN.doc
Page 7
FUNCTIONS DISPLAY
SET AD DR. (Default: 001)
ADDR. 001
RESET MENU
RESET OR NOT
CONFIG. MENU
SET DMX EXT. CHANNEL (Default
DMX EXT. CHANNEL ENABLED
DMX EXT. CHANNEL DISABLED
SET DMX CONTROL CHANNEL (Default
DMX CONTROL CHANNEL ENABLED
DMX CONTROL CHANNEL DISABLED
SET LAMP CONTROL MODE (Default:CTRL)
BY CONTROL CH A NNEL
BY LAMP MENU
BY DMX SIGNAL EXISTING OR NOT
OPTION MENU
SET COLOUR F I LTERS (Default
LINEAR ROTATION DISABLED
LINEAR ROTATION ENABLED
SET GOBO POSITION (Default
LINEAR ROTATION DISABLED
LINEAR ROTATION ENABLED
SET ROTATION OF PAN (Default: O FF)
FORWARD ROTATION
REVERSE ROTATION
SET ROTATION OF TILT (Default :OFF)
FORWARD ROTATION
REVERSE ROTATION
SET PAN&TILT SWAP (Default:OFF)
PAN&TILT SWAP OFF
PAN&TILT SWAP ON
SET DIMMER INVERT(Defaultaa:OFF)
DIMMER INVERT OFF
DIMMER INVERT ON
SET IRES INVERT(Defau ltaa:OFF)
IRES INVERT OFF
IRES INVERT ON
SET ZOOM INVERT(Defaultaa:OFF)
ZOOM INVERT OFF
ZOOM INVERT ON
:
STEP)
:
STEP)
:
ON)
:
ON)
RESET (Default
(CONTINUE)
:
OFF)
DISABLED
ENABLED AND LOAD ALL DEFAULTS
7/18
SOLO 1200 EN.doc
Page 8
DISPLAY MENU(Default:ON)
LCD OF PANEL DISPLAY MODE
LCD IS ON
LCD IS OFF AFTER DELY
LCD IS DARK
INFORMATION MEN U
DISPLAY LAMP'S USING TIME OR SET TO 0
DISPLAY PROJECTOR'S USING TI M E
RESET OR NOT
DISPLAY PROJECTOR'S USING TIME OR SET TO 0
DISPLAY PROJECTOR'S USING TI M E
DISPLAY TEMP ERAT URE
DISPLAY MAIN PCB'S TEMPERATUER
Ⅰ
DISPLAY DRIVER PCB
'S TEMP ERATURE
DISPLAY DRIVER PCB
DISPLAY PAN&TILT DRIVER PCB'S TE MPERAT URE
RESERVED
DISPLAY PROGRAM VERSION
DISPLAY MAIN PCB'S PROGRAM V E R.
DISPLAY MOTOR DRIVER PCB
DISPLAY MOTOR DRIVER PCB
DISPLAY PAN&TILT DRIVER PCB'S PROGRAM V E R.
DISPLAY POWER PCB'S PROGRAM V ER.
TEST ME NU
DEBUG MODE (Default:OFF)
EXIT DEBUG MODE AND RESET
ACCESS DEBUG MODE
SELF-TEST MODE (Def ault:OFF)
EXIT SELF-TEST MODE AND RESET
ACCESS SELF-TEST MODE
Ⅱ
'S TEMP ERATURE
Ⅰ
'S PROGRAM VER.
Ⅱ
'S PROGRAM VER.
LAMP MENU
(END)
(
Default:STAT
DISPLAY STATE OF LAMP
ON
OFF
)
8/18
SOLO 1200 EN.doc
Page 9
REPLACING GOBOS
Lock Tilt.
Loosen 4 screws of the front cover, you will see rotated gobo wheel and fixed gobo wheel.
(As shown in the above fi gure.)
For gobos replacement on the rotated gobo wheel: take an appropriate tool to tug up spring and take
out the rotating gobo with its holder; tug the head of retaining spring up and engage your another
hand to take the retaining spring out; take the gobo out; fit a new gobo and fit the retaining spring; fit
the holder. Notes: the gobo cannot be touched with bare hand; be careful of the gobo when the
replacement is underway and don’t drop it.
For gobos replacement on the fixed gobo wheel: turn the rotated gobo wheel to a proper position first;
take out a gobo from the fixed gobo wheel carefully; fit a new gobo. Note: if the gobo is a glass one, it
should be touched with glabrous, clean and soft tissue or cloth matted between hand and glass
instead of with bare hand.
Close the front cover with 4 screws and fasten 2 latch catches.
CHANGING BELTS
Pan’s belts
Free 2 screws on Pan assembly’s maintenance
door and open the door; change the belts;
close the door and fasten the screws.
Screws
Base
Tilt’s belts
The common users replacing the belts is not
recommended.
White.Note: stay 5 seconds while DMX value is 5, 6or 7, the function reset perform
9/18
Open the door
SOLO 1200 EN.doc
Page 10
DMX CONTROL CHANNEL FUNCTIONS
The SOLO 1200 uses 18 DMX channels. They are listed in the following table.
Channel Function DMX Value Description
000-009 Blackout
010-020 Open
021-034 Strobe 1
035-048
049-062
063-076
077-090
091-104
105-118
1 Strobe
2 Dimmer 000-255 0 to 100% dimming
3 Iris 000-255 Linear adjust iris from open to closed
4 Fixed Gobos
5 Pan rotation 000-255 Pan rotation from 0 to 540º
6 Tilt rotation 000-255 Tilt rotation from 0 to 270º
7 Focus 000-255 Linear adjust iris from near to far
8 Zoom 000-255 Linear adjust angle from narrow to wide
9 Colour Wheel
119-132
133-146
147-160
161-174
175-188
189-202
203-216
217-230
231-244 Strobe 16
245-255 Open
000-020 Clear
021-040 Gobo 1
041-060 Gobo 2
061-080 Gobo 3
081-100 Gobo 4
101-120 Gobo 5
121-140 Gobo 6
141-160 Gobo 7
161-167 Rotation speed 1 (slowest)
168-175
176-183
184-207
208-231 Reverse rotation speed 1 (slowest)
232-239
240-247
248-255
000-016
017-024 White/colour filter 1
025-032 Colour filter 1
Strobe 2
Strobe 3
Strobe 4
Strobe 5
Strobe 6
Strobe 7
Strobe 8
Strobe 9
Strobe 10
Strobe 11
Strobe 12
Strobe 13
Strobe 14
Strobe 15
Rotation speed 2
Rotation speed 3
Rotation speed 4 (fastest)
Reverse rot ation speed 2
Reverse rot ation speed 3
Reverse rotation speed 4 (fastest)
White.Note: stay 5 seconds while DMX value
is 5, 6or 7, t he function reset perform
10/18
SOLO 1200 EN.doc
Page 11
10 Rotated Gobo Wheel
11 Gobo Rotation
033-040 Colour filter 1/colour filter 2
041-048 Colour filter 2
049-056 Colour filter 2/colour filter 3
057-064 Colour filter 3
065-072 Colour filter 3/colour filter 4
073-080 Colour filter 4
081-088 Colour filter 4/colour filter 5
089-096 Colour filter 5
097-104 Colour filter 5/colour filter 6
105-112 Colour filter 6
113-120 white /Colour filter 6
121-127 White
128-133 Rotation speed 1
134-139
140-145
146-151
Rotation speed 2
Rotation speed 3
Rotation speed 4
152-157 Rotation speed 5
158-163
164-169
170-175
Rotation speed 6
Rotation speed 7
Rotation speed 8
176-181 Rotation speed 9
182-187
Rotation speed 10
188-195 Stop rotating
196-201 Reverse rotat i on s p e e d 1
202-207
208-213
214-219
Reverse rot ation speed 2
Reverse rot ation speed 3
Reverse rot ation speed 4
220-225 Reverse rotat i on s p e e d 5
226-231
232-237
238-243
Reverse rot ation speed 6
Reverse rot ation speed 7
Reverse rot ation speed 8
244-249 Reverse rotat i on s p e e d 9
250-255
Reverse rot ation speed 10
000-043 White
044-085 Gobo 1
086-128 Gobo 2
129-170 Gobo 3
171-212 Gobo 4
213-255 Gobo 5
000-120 0~540º index
121-127 Rotation speed 1
128-135
136-143
144-151
152-159
160-167
168-175
176-183
Rotation speed 2
Rotation speed 3
Rotation speed 4
Rotation speed 5
Rotation speed 6
Rotation speed 7
Rotation speed 8
184-191 Stop rotating
11/18
SOLO 1200 EN.doc
Page 12
192-199 Reverse rotation speed 8
200-207 Reverse rotation speed 7
208-215 Reverse rotation speed 6
216-223 Reverse rotation speed 5
224-231 Reverse rotation speed 4
232-239 Reverse rotation speed 3
240-247 Reverse rotation speed 2
248-255 Reverse rotation speed 1
000-051 Clear
052-102 Prism 1
12 Prisms
103-153 Prism 2
154-204 CTB
205-255 CTO
000-120 0~540º index
121-127 Rotation speed 1
128-135 Rotation speed 2
136-143 Rotation speed 3
144-151 Rotation speed 4
152-159 Rotation speed 5
160-167 Rotation speed 6
168-175 Rotation speed 7
13 Prism Rotation
176-183 Rotation speed 8
184-191 stop rotating
192-199 Reverse rotation speed 8
200-207 Reverse rotation speed 7
208-215 Reverse rotation speed 6
216-223 Reverse rotation speed 5
224-231 Reverse rotation speed 4
232-239 Reverse rotation speed 3
240-247 Reverse rotation speed 2
248-255 Reverse rotation speed 1
Pan & Tilt Speed
14
（Extended function）
000-255 Adjust Pan&Tilt speed from fast to slow
Pan Fine (16Bit)
15
（Extended function）
000-255 Adjust Pan in 16Bit resolution
Tilt Fine (16Bit)
16
（Extended function）
000-255 Adjust Tilt in 16Bit resolution
Gobo Rotation Fine
17
（Extended function）
000-255 Adjust gobo rotation in 16Bit resolution
000-048 Reserve
049-080 Reset
081-112 Reserve
113-144
Turn lamp off（stay 10 seconds）
145-223 Reserve
224-255
Turn lamp on（see remark below）
18
Control
（when extended functions
are invalid, shift this
channel to 15
th
channel.）
Remark:
If you intend to turn on/off the lamp via t he 18th channel of the controller, don’t attempt to push the
slide bar of 18
value 224-255 to wait it cooling. Under these 2 circumstances, the lamp can not be turned on. The
th
channel to value 224-255 immediately after turning it off, or push the slide bar to
12/18
SOLO 1200 EN.doc
Page 13
right operation is: turn it off---cool down---push the slide bar to turn it on.
LED INDICATION
Green: ON——DMX signal OK or Slave;
OFF——No DMX signal;
Flash——DMX signal error;
Red: Flash medium——Setting menu mode ;
Flash fast——Software or CPU fault ;
If the projector’s lens becomes damaged or broken it should be replaced. If the lamp becomes
damaged or deformed in any way it must be replaced. If the light from the lamp appears dim this
would normally indicate that it is reaching the end of its life and it should be changed at once, aged
lamps run to the extremity of their life might explode. If the projector does not function, check the
fuses on the power socket of the projector, they should only be replaced by fuses of the same
specification. Should these be damaged call a qualified technician before replacement. The projector
has thermal protection device that will switch off the projector in case of overheating, should either of
these operation, check that the fans are not blocked, and if they are dirty clean them before switching
on the projector again. Check that the fans are operational, if not call a qualified technician.
Any maintenance work should only be carried out by qualified technicians.
MAINTENANCE
LUBRICATION
To ensure the continuous rotation of the rotating gobos and linear motion of the lens for focusing, it is
recommended that the bearings for the rotating gobos and the 3 shafts for the focusing lens holder be
lubricated periodically, preferably every two months. Use only high quality, high-temperature resistant
grease instead of any type of oil. When lubricating the bearings, a syringe with a fine needle is the
easiest way to introduce the grease to the bearings around each gobo.
KEEPING THE PROJECTOR CLEAN
To ensure the reliability of the projector it should be kept clean. It is recommended that the fans
should be cleaned every 15 days. The lens and dichroic colour filters should also be regularly cleaned
to maintain an optimum light output.
Cleaning frequency depends on the environment in which the fixture operates: damp, smoke or
particularly dirty surroundings can cause greater accumulation of dirt on the unit’s optics. A soft cloth
and typical glass cleaning products should be used in cleaning. It is recommended to clean the
external optics at least once every 20 days and clean the internal optics at least once every 30 / 60
days.
Do not use any organic solvent, e.g. alcohol, to clean the reflector mirror, dichroic colour filters
or housing of the apparatus.
Do NOT use any type of solvent on dichroic colour filters.
13/18
SOLO 1200 EN.doc
Page 14
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE ACTION
The projector doesn’t switch
on
The lamp comes on but the
projector doesn’t respond to
the controller
The projector only func tions
intermittently
Defective projection
The projected image
appears to have a halo
The beam appears dim
-The power supply is not
present
-The lamp doesn’t work
-Wrong DMX configuration
and/or start address
- Defective DMX c abl e
-The fan has failed
-The lens is broken
-Dust or grease on lenses
-Installation of the lamp is not
correct
-Dust or grease contamination
on the optics.
-Dust or grease contamination
on the optics.
-The lamp is at the end of its
life
Check the fuse on the power
socket.
Replace the lamp.
Make sure that the projector is
correctly configured.
Replace or repair the DMX cable.
Make sure the fan is working and
not dirty.
Check the lenses are not broken.
Remove dust or grease from the
lenses.
Make sure the lamp is installed
correctly.
Carefully clean the optical group
lenses and the projector
components.
Check the optics is clean.
Replace with a new lamp of the
specified type and rating.
LIGHT OUTPUT
22.6°（ lux
16°（ lux
）
）
8625
11980
5402156 950
13302995 750
345
480
5m
4m
3m
2m
1m
0m
1m
2m
3m
4m
5m
DISTANCE (m)
16° DIAMETER (m)
22.6° DIAMETER (m)
22.6°
16°
0
0
5
1.41
2.00
0
10
2.82
4.00
15
4.23
6.00
20
6.64
8.00
25
7.05
10.0
14/18
SOLO 1200 EN.doc
Page 15
TECHNICAL DATA
VOLTAGES: 200/220/230/240V AC, 50Hz or 60Hz to order
POWER CONSUMPTION:
1400W
LAMP: Type: PHILIPS MSR 1200 SA/DE
Or OSRAM HMI 1200W/S
Colour Temperature: 6000ºK
Socket: GY22, single end
Manufacturers Rated Lamp Life: 750 Hours
COLOURS:
1 colour wheels, 6 dichroic colours plus white each wheel
Adjustable speed with rainbow effect
COLOUR TEMPERATURE CORRECTION:
1 colour temperature corrective filters
GOBOS:
Rotated gobo wheel
5 interchangeable gobos+white, indexical, bidirectionally rotatable in adjustable
speed respectively
Fixed gobo wheel
7 interchangeable gobos+white, bidirectionally rotatable in adjustable speed
wholly
Gobo diameter: 36.3mm
Gobo image diameter: 31.5mm
PRISM WHEEL:
1x white, 1x 2 facet prism, 1x 3 Facet prism, 1x CTO, 1x frost
FOCUS:
DMX controlled focus
SHUTTER:
Double shutter blades, 0-100% linearly adjustable
STROBE:
0.3~6 F.P.S.
HEAD MOVEMENT:
Pan 540º, Tilt 270º
BEAM ANGLE:
16º~ 22.6º
CONTROL:
DMX512, 18 Channels
HOUSING:
Composite plastic (IP20)
NET WEIGHT:
40
Kg
SIZES:
520
550
805
835
490
15/18
640
670
580
SOLO 1200 EN.doc
Page 16
ELECTRICAL DIAGRAM
LAMP
1200W
60Hz
50Hz
60Hz
Ignitor
Thermostat
70uF 370V
CAP2
70uF 370V
CAP1
50Hz
Ballast2
Ballast1
Push-SW2Push-SW1
230V
220V
Transformer
24VAC
Filter
0V
Delay Fuse
E
AC Plug
LN
View side o f no axletree
PRISM ROTATIO N
M2-6
View side o f no axletree
PRISM
M2-5
MOTOR6
H6
H5
H2
CAP
View of mark side
HALL 2-1
View of mark side
MOTOR5
HALL 2-2
LAMP
H4
H1
230VAC
DISPLAY P C B
TO BALLAST
FREQUENCY SE LECT
View side of no axletree
IRIS
M2-4
View side of no axletree
FOCUS
M2-3
View side of no axletree
GOBO ROTATION
M2-2
ROT-GOBO WHEEL
M2-1
View side of no axletree
MOTOR4MOTOR3
No Encoder Side
SLAVE #2 PCB
MOTOR2
MOTOR1
MOTOR6MOTOR5
SENS2
SENS1
GND
SENS4
SENS3
SENS6
SENS5
H10
GND
DMX-SENS2
DMX-SENS1
VCC
VCC
GND
GND
View of mark side
HALL 2-3
View of mark side
HALL 2-6
View of mark side
HALL 2-5
BOX FAN
POWER PCB
1/2 POWER
3/4 POWER
FAN4
FAN3
H9
H8
POWER
GND
POWER
FEEDBACK
HEAD FAN
GND
VCC
VCC
DMX-SENS2
DMX-SENS1
24VAC
FULL
FAN2
FEEDBACK
H3
FULL
FAN1
H7
DMXDMX
HEAD FAN HEAD FAN
DMX-IN
DMX-OUT
GND
GND
VCC
VCC
DMX-SENS1
DMX-SENS2
DISPLAY DR I VE PCB
DMX-IN
DMX-OUT
View of mark side
HALL 1-2
View of mark side
HALL 1-1
View side of no axletree
STROBE 2
M1-5
TILT2TILT1PAN2
PAN ENCODE
View side of no axletree
STROBE 1
M1-4
View side of no axletree
ZOOM
M1-3
View side of no axletree
COLOR
M1-2
FIXED GOBO
M1-1
View side of no axletree
MOTOR4
Encoder Side
SLAVE #1 PCB
MOTOR3
MOTOR2MOTOR1
SENS2
SENS1
View side of no axletree
Encoder motor
SENS4
SENS3
SENS6
SENS5
View of mark side
DMX-SENS2
DMX-SENS1
VCC
VCC
GND
HALL 1-3
GND
TILT1
PAN-Encoder
View side of no axletree
No encoder motor
PAN2
View side of no axletree
Encoder motor
PAN1
DBCA
TILT-Encoder
DMX-SENS2
DMX-SENS1
VCC
VCC
GND
GND
TILT ENCODE
16/18
SOLO 1200 EN.doc
Page 17
COMPONENT ORDER CODES
NAME PART NO. QUANTITY REMARK
TRANSFORMER
THERMOSTAT
CAPACITOR
BALLAST
IGNITOR
LAMP
PAN&TILT DRIVE BELT 290151221 3 HTD459-3M-6
FUSE
FAN
FAN
FAN
PAN MOTOR 030040089 2 23HS2039L 6.35*25
TILT MOTOR 030040089 1 23HS2039L 6.35*25
ZOOM MOTOR 030040094 1 17HD0013-35L 5*7
COLOUR WHEEL MOTOR 030040094 1 17HD0013-35L 5*7
FIXED GOBO WHEEL MOTOR 030040094 1 17HD0013-35L 5*7
PRISM MOTOR 030040094 1 17HD0013-35L 5*7
FOCUS MOTOR 030040093 1 17HD0013-33L 5*7
ROTATING GOBO WHEEL MOTOR 030040093 1 17HD0 013 -33L 5*7
STROBE MOTOR 030040112 2 17HD0013-38L 5*15
IRIS MOTOR 030040092 1 17HD0013-32L 5*7
PRISM ROTATION MOTOR 030040095 1 17HD0013-36L 5*7
GOBO ROTATION MOTOR 030040095 1 17HD0013-36L 5*7
PAN&TILT DRIVE PCB
MOTOR DRIVER PCB Ⅰ 230020160
MOTOR DRIVER PCB Ⅱ
DISPLAY PCB 230020096 1
DIGITAL DRIVER PCB
POWER PCB 230020098 1
NOTE: You may order all parts of the SOLO 1200 besides the table listed above. When ordering
please state the exact name and part no. Repairs must be carried out by a qualified technician.
040030053 1 220/230V
190010035
140010043 1 70µF/370V
040070059 2 230V/50-60Hz, 575W
040090036 1 575~1200W 3~5KV
100050054 1 PHILIPS MSR 1200 SA/DE
270041044 1 6.35x32 15A/250V
030060035 1 KD2409PTB1-6 24VDC
030060031 1 KD2406PTS1-6 24VDC\2.6w
030060039 2 DC24V 0.49A NMB
230020159 1
230020161
230020162 1
1
1
1
KSD020 120℃/15A/250V
17/18
SOLO 1200 EN.doc
Page 18
PR LIGHTING LTD.
No. 571, Yingbin Road, Dashi, Panyu, Guangzhou, China
Post-Code: 511430
TEL: +86-20-8478 1888
FAX: +86-20-8478 6023
P/N: 321010223
Last Revision: 07:05:2006
18/18
SOLO 1200 EN.doc
Loading...