OmniSistem PR Panda II (KB) User Manual

PANDA II

PR- 2100B

This product manual contains important information about the safe installation and
use of this projector. Please read and follow these instructions carefully and keep this
manual in a safe place for future reference.

PR LIGHTING LTD.

Yingbin Road, Dashi Panyu, Guangzhou, 511430 China

http://www.pr-lighting.com

INDEX

SECTION PAGE

SAFE USAGE OF THE PROJECTOR 3
INSTALLING THE PROJECTOR 4
FITTING THE LAMP 4
POWER SUPPLY – MAINS 5
OPERATION 5
STAND-ALONE MODE 5
XLR CONNECTORS AND TERMINATOR 5
MASTER/SLAVE SYNCHRO MODE 6
CONTROLLER MODE – DMX 512 OPERATION 7
REMOTE CONTROLER MODE 9
MAINTENANCE 9
KEEPING THE PROJECTOR CLEAN 9
TROUBLE SHOOTING 10
TECHNICAL DATA 10
ELECTRICAL DIAGRAM 11

Please note that as part of our ongoing commitment to continuous product development, specifications are subject to change

without notice. Whilst every care is taken in the preparation of this manual we reserve the right to change specifications in the

course of product improvement. The publishers cannot be held responsible for the accuracy of the information herein, or any

consequence arising from them.

Every apparatus is tested completely and packed properly by the manufacturer. Please make sure the packing and / or the

apparatus is in good condition before your installation and use. Should there be any damage caused by transportation, consult

your dealer and do not use the apparatus. But any damage caused by improper use will not be assumed by the manufacturer

and / or dealer.

THESE ITEMS ARE PACKED TOGETHER WITH THE PROJECTOR

Inner Bracket (1 PCS)
Outer Bracket (1 PCS)
M8 knobs for bracket (2 PCS)
Power-cord (1 PCS)
XLR plug (1 PCS)
XLR socket (1 PCS)
This manual (1 PCS)
Remote Controller (Optional)

Thank you for purchasing our product PANDA II PR-2100B.
This product manual contains important information about the safe installation and use of this projector.
Please read and follow these instructions carefully and keep this manual in a safe place for future
reference.
PANDA II adopts advanced procedure of design and manufacturing and uses international protocal
DMX 512 and compiles to CE norms. The figure of housing is elegant, lovable and portable, which
features its special character compared with conventional luminaire. PANDA II can be suspended from
the ceiling or be seated on the floor with the inner and outer brackets provided and the angle of the
body is easy to be adjusted, and the projector even can be carried by hand.
The programmes having been set in the PANDA II may be actived by sound or controller. The PANDA
II can be used as a stand-alone unit or linked with each other for multi-units or linked to a controller, so
it is suitable for many different applications. PANDA II uses an OSRAM ERF 15V/150W lamp with
adjustable lamp brightness via controller and uses 14 gobos and 14 colourful glass filters, so the
producing light beam is bright and sharp.
PANDA II will switch off the lamp automatically after 8 seconds of shutter, so it can effectively prolong
the life of the lamp. The gobo/colour wheel rotating quickly can produce rainbow or strobe effect. In
addition, you may use remote controller with a long distance to control the luminairs for shutter, strobe
and fast/slow action to audio.

ACCESSORIES

INTRODUCTION

2/12

panda II manual.doc

SAFE USAGE OF THE PROJECTOR

The following points are important for safety as well as for the smooth
installation and performance of the unit

When unpacking and before disposing of the carton check there is no transportation damage before
using the projector. Should there be any damage caused by transportation, consult your dealer and do
not use the apparatus.

The projector is for Indoor use only, IP20. Use only in dry locations. Keep this device away from rain
and moisture, excessive heat, humidity and dust. Do not allow contact with water or any other fluids, or
metallic objects.

The projector is not designed or intended to be mounted directly on to inflammable surfaces.

The projector is only intended for installation, operation and maintenance by qualified personnel.

The projector must be installed in a location with adequate ventilation, at least 50cm from adjacent
surfaces. Be sure that no ventilation slots are blocked.

Do not project the beam onto inflammable surfaces, minimum distance is 3m.

Avoid direct exposure to the light from the lamp. The light is harmful to the eye.

Do not attempt to dismantle and/or modify the projector in any way.

Electrical connection must only be carried out by qualified personnel.

Before installation, ensure that the voltage and frequency of power supply match the power
requirements of the projector.

It is essential that each projector is correctly earthed and that electrical installation conforms to all
relevant standards.

Do not connect this device to any dimmer pack.

Make sure that the power-cord is never crimped or damaged by sharp edges. Never let the power­cord come into contact with other cables. Only handle the power-cord by the plug. Never pull out the
plug by tugging the power-cord.

Never run the projector without a lamp.

There are no user serviceable parts inside the projector, do not open the housing and never operate
the projector with the covers removed.

Do not use any organic solvent, e.g. alcohol, to clean the lenses, dichroic colour filters, anti-heating
glass, reflector mirror or housing of the projector.

3m

Always disconnect from the mains, when the device is not in use or before cleaning it
or before attempting any maintenance work.

If you have any questions, don’t hesitate to consult your dealer.

3/12

panda II manual.doc

INSTALLING THE PROJECTOR

There are two ways to install the projector either hanging the projector from the ceiling or sitting on the
floor.
Mount the inner and outer brackets provided on the body of the projector. There are 2 M8 knobs
provided to tighten the body of the projector and the two brackets. When you want to adjust the angle
of the body of the projector, you only loosen the two M8 knobs carefully and then adjust the angle of
the body. After finishing that, it is recommended that you don’t forget to retighten the two M8 knobs.
Always ensure that the projector is firmly positioned to avoid vibration and slipping. For suspending the
projector always ensure that the structure to which you are attaching the projector is secure and is
able to support a weight of 6kg for each PANDA II.

FITTING THE LAMP

Remove the upper cover by loosening the 2 M4 taping screws and 1 M4 knurling screw.
Insert an EFR 15V/150W lamp in the lamp porcelain holder. (When replacing a lamp, you should
first pull out the old lamp from the lamp-bracket.)
Push the lamp into the position seat of the lamp-bracket carefully.

Install the upper cover again. (Note: Do not forget to connect the grounding-cord with the upper

cover.)
Retighten the 2 M4 screws and 1 M4 knurling screw.

4/12

panda II manual.doc