OmniSistem PR Orland Follow Spot User Manual

ORLAND FOLLOW

PR-1211

This product manual contains important information about the safe installation and
use of this projector. Please read and follow these instructions carefully and keep this
manual in a safe place for future reference.

PR LIGHTING LTD.

Yingbin Road, Dashi Panyu, Guangzhou, 511430 China

http://www.pr-lighting.com

Orland Follow manual.doc

INDEX

SAFE USAGE OF THE PROJECTOR 3
OPERATION 4
FITTING THE LAMP 5
MASTER/SLAVE SYNCHRO MODE 5
MAINTENANCE 6
KEEPING THE PROJECTOR CLEAN 7
TROUBLESHOOTING 7
TECHNICAL DATA 7

Please note that as part of our ongoing commitment to continuous product development, specifications are subject to change
without notice. Whilst every care is taken in the preparation of this manual we reserve the right to change specifications in the
course of product improvement. The publishers cannot be held responsible for the accuracy of the information herein, or any
consequence arising from them.
Every apparatus has been tested completely and packed properly by the manufacturer. Please make sure the packing and / or
the apparatus is in good condition before your installation and use. Should there be any damage caused by transportation,
consult your dealer and do not use the apparatus. But any damage caused by improper use will not be assumed by the
manufacturer and / or dealer.

ACCESSORIES

THESE ITEMS ARE PACKED TOGETHER WITH THE PROJECTOR

5-PIN XLR plug(1PCS)

5-PIN XLR socket(1PCS)
3-Foot bracket (1 SET) (Optional)
This manual (1 PCS)

INTRODUCTION

Thank you for purchasing the product Orland Follow, PR-1211.
This product manual contains important information about the safe installation and use of this
projector. Please read and follow these instructions carefully and keep this manual in a safe place
for future reference.
The Orland Follow is an innovative projector with an elegant housing made from high quality
aluminiun-alloy and steel with an epoxy paint finish. The Orland Follow complies to CE norms and
standards and uses international protocol DMX-512.
The Orland Follow uses HMI 1200W lamp and high quality optical systems which produce bright
and beautiful light beam, and it can continuously adjust the brightness from 0% to 100% via the
mechanical device. The Orland Follow features effects of strobe, soft light beam, mixing colours
and rainbow, and the projector may be used in stand-alone mode or synchro mode, so it is
suitable for use in TV station, disc, singing and dancing stage, night club and so on.
The Orland Follow is controlled by dedicated manual controller, and the operation is easy and
convenient. The unit is installed on the 3-foot bracket, and the angle and the height of the body
are easy to be adjusted.
The projector has protection devices of auto thermal cut-off and lamp power cut-off in case you
directly open the cover for lamp replacement before switching off the general switch.

2/8

Orland Follow manual.doc

When unpacking and before disposing of the package check there is no transportation damage
before using the projector. Should there be any damage caused by transportation, consult your
dealer and do not use the apparatus. Keep the package well for your possible future
transportation.

The projector is for indoor use only, IP 20. Use only in dry locations. Keep this device away from
rain and moisture, excessive heat, humidity and dust. Do not allow to contact with water or any
other fluids, or metallic objects.

The projector is not designed or intended to be mounted directly on to inflammable surfaces.

The projector is only intended for installation, operation and maintenance by qualified personnel.
The projector must be installed in a location with adequate ventilation, at least 50cm from

adjacent surfaces. Be sure that all the cooling fans run normally and no ventilation slots are
blocked.

Do not project the beam onto inflammable surfaces, minimum distance is 3m. 3m
Avoid direct exposure to the light from the lamp. The light is harmful to the eye.
Do not attempt to dismantle and / or modify the projector in any way.
Electrical connection must only be carried out by qualified personnel.
Before installation, ensure that the voltage and frequency of power supply match the power

requirements of the projector. Only use the lamp with the specified type and rating.
It is essential that each projector is correctly earthed and that electrical installation conforms to all

relevant standards.
Do not connect this device to any dimmer pack.
Make sure that the power-cord is never crimped or damaged by sharp edges. Never let the

power-cord come into contact with other cables. Only handle the power-cord by the plug. Never
pull out the plug by tugging the power-cord.

Keep the lamp clean. Do not touch the lamp glass with bare hand.
The lamp used in this projector is an high power discharge lamp. After being switched off don’t

attempt to restart the projector until lamp has cooled, this will require approx 15 minutes.
Switching the lamp on and off at short intervals will reduce the life of both the lamp and the
projector. Occasional breaks will prolong the life of both the lamp and the projector.

Never run the projector without a lamp.
There are no user serviceable parts inside the projector, do not open the housing and never

operate the projector with the covers removed.

SAFE USAGE OF THE PROJECTOR

Always disconnect from the mains, when the device is not in use or before
cleaning it or before attempting any maintenance work.

If you have any questions, don’t hesitate to consult your dealer or manufacturer.

3/8